209 not categorized PORSCHE 356C EXHAUST SYSTEMCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 2009-12 (includes uncategorized and accessory items) BES98115001SK This is our jekyll and hyde version ! The perfect compromise for you and your loved ones. Rich, deep race car tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english, and is the best choice for a daily driver. + 11 hp & + 10 tq gain. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 1/2 tubing (63.5 mm). - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin (200 rpms worth) compared t...(choose a part on the right to read more)
$5,197.50
Make a selection AP958170 Agency power is proud to release its super sport exhaust system for the 958 Porsche Cayenne s v8 2011 and up. the super sport exhaust is a axle system that gives your 4.8l v8 engine a real aggressive tone. made here in the usa, the exhaust saves close to 30lbs off the rear end of the vehicle. using 304 stainless steel and detail oriented tig welding, the exhaust system uses two small high flow mufflers which give it the sports car rumble. its reduced back pressure design gives the engine improved horsepower and torque with most noticeable improvement in throttle response. because of the reduced restriction, this exhaust horsepower gains can definitely be noticed in the mid to top rpm range.
$1,495.95
Make a selection BBI9912020003 The bbi autosport 997 & 991 GT3 / rs exhaust side bypass is a direct replacement for the factory primary side mufflers. The primary mufflers are weigh approximately 44 pounds total while the bbi pipes are 4 pounds in comparison. For durability and protection against corrosion, each system is meticulously tig welded using 304 aerospace grade stainless tubing with lower carbon content. The result is a substantial reduction in weight behind the rear axle which significantly improves handling and less restriction to produce a much more aggressive exhaust note.
$950.00
Make a selection 150BP1027 Book description: publication date: january 15, 1999 inside this manual you will find routine maintenance, tune-up procedures, engine repair, cooling and heating, air conditioning, fuel and exhaust, emissions control, ignition, brakes, suspension and steering, electrical systems, and wiring diagrams.
$82.50
Make a selection 99611198200 Beautiful chrome-plated exhaust tail pipe tips made of stainless steel and featuring a larger, oval cross section for a more powerful appearance. Also fits the sport exhaust system for the final finishing touch. Priced per each.
$495.89
Make a selection 220110932ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original 2.4-inch (63 mm) to a 2.6-inch (66.5 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. FVD thrott...(choose a part on the right to read more)
$485.10
Make a selection 22011090102ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original to a 2.7-inch (70.5 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. Each throttle body is reman...(choose a part on the right to read more)
$589.60
Make a selection 21011125PSE Only for vehicles with Porsche standard sports exhaust system 200 cell, hjs tri-metal, hf (high flow) hjs catalytic cores with "u-torque" design, manufactured by m in Germany. The u-torque design compensates for the backpressure loss while running the high flow cats. The design minimizes the loss of low end torque and adds 10-15 ft-lbs of torque in the mid and top range of the rpms. Why settle for the traditional cross over cat design when you can add more torque in the mid-range and minimize the loss of torque down low where the 997's need it most! Please note: these fit the OEM mufflers and Porsche sport exhaust (pse) mufflers. Tech tip:add one of our installation kits FVD mk 997300
$3,311.00
Make a selection 100211022SSIRE This heat exchanger is engineered for the discerning Porsche 911 owner. Ssi heat exchangers are made from superior t 304 grade (18% cr, 8%+ ni) stainless steel. Ssi has become an industry standard for Porsche 911 heat exchangers due to the exceptional materials, craftsmanship and durability. This is critical when considering heat exchangers, as exhaust leaks caused by poor materials can lead to carbon monoxide entering the cabin via the heating system. Features: t304 stainless steel (18% cr, 8%+ ni) backpressure reduction bolt on replacement reduces the thermal load on the motor sold individually. 1 necessary per car.
$728.20
Make a selection 150BP264 Book description: publication date: january 15, 1999 inside this manual you will find routine maintenance, tune-up procedures, engine repair, cooling and heating, air conditioning, fuel and exhaust, emissions control, ignition, brakes, suspension and steering, electrical systems, and wiring diagrams.
$108.90
Make a selection 100211021SSI This heat exchanger is engineered for the discerning Porsche 911 owner. Ssi heat exchangers are made from superior t 304 grade (18% cr, 8%+ ni) stainless steel. Ssi has become an industry standard for Porsche 911 heat exchangers due to the exceptional materials, craftsmanship and durability. This is critical when considering heat exchangers, as exhaust leaks caused by poor materials can lead to carbon monoxide entering the cabin via the heating system. Features: gains of +10-15 hp and +10-20 tq t304 stainless steel (18% cr, 8%+ ni) increased pipe diameter for backpressure reduction connects to "early style" dual inlet mufflers bolt on replacements reduces the thermal load on the motor includes custom torque w...(choose a part on the right to read more)
$2,864.40
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |