Vehicles
Sections
130 not categorized PORSCHE 356 A A ARM BUSHINGSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 TURBO/GT2 2007-09 (includes uncategorized and accessory items) FVD205993001VA H&r front sway bar with a 26 mm diameter. 2-way adjustable. This is the front sway bar from our kit, part # FVD205993001. Includes bushings. Sold individually. 1 needed per car.
$473.00
Make a selection FVD33150040R Replace worn-out original rear sub frame (side panel) bushings with our FVD clubsport series. They are made of rubber with an 85 shore hardness value, that is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. We also sell the entire right and left rear sub frames with these bushings already installed, please order our part # FVD331993001.
$429.00
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection FVD34101702RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$451.96
Make a selection FVD205996003VAG These bushings are made for h&r front sway bars with 25 mm diameters. They are a direct replacement for our part # . These will also work on any bar with a 25-mm diameter. If you would also like to replace the rear, please use part # FVD205996003hag sold as a front set. 1 set needed per car.
$58.30
Make a selection FVD33391100SET Replace worn-out original spring plate bushings to return your car to its intended ride quality and performance. This is a high-quality OEM 65 shore density bushing set, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD34101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD33394401SET Replace worn-out original spring plate bushings to return your car to its intended ride quality and performance. This is a high-quality OEM 65 shore density bushing set, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This set is a direct replacement for the rear axle strut bushings from original part # 477 511 201 and 477 511 202 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD37504332R Replace the worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushings. These are manufactured of rubber with an 85-shore hardness value. 85-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings. Rubber has a shore hardness value of 85 (like rs models) made in Germany sold as a set. 1 necessary per car.
$152.90
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection 99711608690 Includes bushings. Oem specifications. We recommend our part # FVD116999 which includes this clutch fork and everything needed for installation. Not sure which clutch parts are right for your car? We have pre-packaged kits that include everything that you need for installation. Check them out under the clutch kits category. View/Change Diagram
From $143.58
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection SPLDB996 Spl titanium rear camber links allow for an increased range of rear camber adjustment, necessary for lowered street cars and performance alignments for racing. The next generation nct motorsports bearing feature a carbon fiber teflon liner to provide quiet operation, lower friction, smoother articulation and eliminates bushing deflection under load. the injection-molded slot-loaded liner is also self-lubricating and self-cleaning, offering robust reliability for street and track use. Pair with the spl titanium rear toe links and spl eccentric lockout kit for total rear camber and toe alignment with "zero-slip". General Fitment911 1998-05911 TURBO/GT2 2001-05 911 2005-08 911 GT3 2007-11 911 TURBO/GT2 2007-09 911 2009-12 911 TURBO/GT2 2010-13
$943.65
Make a selection FVD424041 Ok, we know you are a driving enthusiast if you are shopping for a short shifter for your manual transmission. Driving enthusiasts appreciate a more direct connection to the car, transmission and road surface. If you are trying to clean up those long shifts and side to side play on the factory shifter you are certainly on the right track with this upgrade. This numeric racing short shift kit uses precision ball bearings on all axis' which produce 35% shorter throws with an almost gated like action. Short gated like throws increase your driving experience by enhancing a more direct, mechanical connection to your car. Once installed you will find joy with every shift and this will easily become one of your favor...(choose a part on the right to read more)
$808.50
Make a selection
From $138.80
Make a selection 477511201BU
$108.90
Make a selection 61610314252SET8
$148.50
Make a selection 61610314262SET8
$89.10
Make a selection 150SPB968
$35.20
Make a selection 91410314100SET High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 necessary per car.
From $103.40
Make a selection 91410314150SET High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 necessary per car.
$148.50
Make a selection 92810314315SET
$114.40
Make a selection 90134378300EQ High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 4 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$6.60
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |