Vehicles
Sections
471 not categorized PORSCHE 986 CONTROLCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 TURBO/GT2 2007-09 (includes uncategorized and accessory items) 99761353501A05
$153.53
Make a selection 99752163303V05 Known as: galvano silver View/Change Diagram
$50.26
Make a selection 99763118300
$946.20
Make a selection 99911341840 Known as: gasket g5050 1k00695>> g5050 2k00539>> / gasket / gasket 13,02 x 16,4 View/Change Diagram
From $2.52
Make a selection BBI9974010001 Features
$1,895.00
Make a selection BBI9964010002 Finally, a complete solution to properly widen the front track width of a Porsche 996 and 997 turbo. To help increase front end grip, this kit allows full negative camber adjustment without binding the axles and fitment of wider wheel/tire combinations and GT3 cup car fenders. Each kit includes lower control arms, thrust arms, axle spacers, upper mounts, and camber shims.
$3,695.00
Make a selection 99764220100A05 Known as: black mat for control part see technical information gr. 9 . Nr. 6/04 View/Change Diagram
From $10.00
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$451.96
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection BESKLS000002 This remote will allow you to control the valved exhaust with the touch of a button on your key chain. Our remote control unit is compatible with the FVD valved mufflers and exhaust systems as well as the FVD retro fit valve kit bes kls 000 001 . General Fitment911 GT3 2007-11911 TURBO/GT2 2007-09 911 2009-12 911 2005-08 911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05 911 1994-98 CAYMAN 2009-12 CAYMAN 2006-08 BOXSTER 2009-11 BOXSTER 2005-08 CAYENNE 2003-06
$401.74
Make a selection 9975223220001C
$3.31
Make a selection FVD34101702RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and r...(choose a part on the right to read more)
$440.00
Make a selection FVD33150045R Replace worn-out soft rubber (65 shore hardness value) control arm bushings (camber link and caster link) with sportier rubber (75 shore hardness value) that is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$69.30
Make a selection FVD34101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD34199691 Allows greater camber adjustment possibilities at the front using the 2-piece split control arm set. Includes 1, 2, 3, and 10mm shims to cover a wide range of camber adjustment. A must for track and club sport vehicles. General Fitment911 TURBO/GT2 2007-09911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
From $1,849.17
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD34105304BU1 Diese buchse ersetzt an ihrem vorderen querlenker die mittlere buchse. Es handelt sich bei dieser buchse um einen hartegrad von 85 shore wie original bei den rs -modellen ( GT3 rs, GT2 rs ) preis pro stuck, pro querlenker wird ein stuck benotigt.
$115.50
Make a selection FVD34199690 Allows greater camber adjustment possibilities at the front using the 2-piece split control arm set. General Fitment911 TURBO/GT2 2007-09911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
$2,638.72
Make a selection FVD34101802RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and re...(choose a part on the right to read more)
$440.00
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD33150045 Original rubber replacement bushing (65 shore hardness value) for the rear control arms (camber link and caster link). This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$64.90
Make a selection FVD631997TLED This works on FVD bromacher led's, part # FVD 631 997 03 to make the daytime running lights dim when the headlights are turned on. This is also mandatory for FVD 631 997 fled if you want to have the daytime running lights dim when you turn the headlights on. General Fitment911 GT3 2007-11911 TURBO/GT2 2007-09 911 2005-08
From $477.00
Make a selection FVD99161801R01
$1,608.20
Make a selection
$307.70
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |