193 not categorized PORSCHE 964 SOLD CARCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 TURBO/GT2 2007-09 (includes uncategorized and accessory items) 96434350301 This is the lower strut plate that retains the spring and sits on top of the adjusting nut. We recommend that you inspect and replace if necessary with any new shock install. This plate tends to suffer from corrosion as debris collects in it with time. Sold individually. Right or left side fitment. 2 necessary per car.
From $39.00
Make a selection 96434732202EQ The symptoms of a worn tie rod end include, clunking, rattling and squeaking when turning, poor alignment and premature tire wear. Have the rod ends inspected when servicing your suspension and proactively change them when noticing any of the symptoms. Sold individually. Left or right side fitment. 2 necessary per car.
$49.50
Make a selection 96453109500EQ This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.
$215.60
Make a selection FVD33396410 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of eibach pro kit springs. This suspension kit is meant for those who want the car to sit at the lowest possible ride height. This set up will allow you to lower the front axle by 2.4 inches (60 mm). This is a perfect kit for clubsport or race use where the surfaces are smooth and even. The stock rs ride height was 1.6 inches (40 mm) lower. So, this is a full 3/4 of an inch (20 mm) lower on the front axle. Sold as a complete kit. 1 kit is necessary per car. Please note: we recommend the b6 / ohlins suspension kits for those looking for more comfort for street use.
$2,726.50
Make a selection 964541225001 This genuine Porsche windshield seal is an integral part of keeping your cowl from rusting. It is critical that the gasket and windshield are properly installed to prevent corrosion. Sold individually. 1 needed per car. Please note: for the 911 models, this does not contain the trim frame slot for chrome / black trim like the earlier cars.
$406.00
Make a selection 964565035017EQ This is genuine targa top material sourced from Germany. It is as close to the original as possible and is cut and trimmed to fit perfectly. We also make sure that there is plenty of material to stretch out the sides so that there are no wrinkles when installed. Sold individually. 1 necessary per car.
$335.50
Make a selection 99336105700EQ Genuine quality wheel nut and lock set in black. The set includes a key. Please check the exact model designation for this part below. Sold as a set. 1 set necessary per car.
$106.70
Make a selection 96560612601EQ Oxygen or lambda sensors are critical to your engines health. If the sensor is faulty you may experience poor gas mileage, rough idling or engine pinging. High-quality replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Be sure to check the "fits these models" tab to make sure that this will work for your needs. Sold individually. 1 necessary per car.
$111.10
Make a selection 99310605180 Allows you to convert to one fan belt to run the fan and alternator like the factory rs versions. Oem part sourced in Germany to ensure quality, reliability and precise fitment. Once installed the alternator will run at the fan speed. That will lessen the inertial load and will add slightly more horsepower and acceleration. - includes fasteners (3 qty. M 6x35) - weighs .4 lbs ( .17 kg) please note: for 993 race car conversions or for cars without a/c we also recommend the corresponding crankshaft pulley, part # 99310205040 sold individually. 1 necessary per car.
From $152.90
Make a selection 99333167100 Sold individually. All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$581.90
Make a selection 993555032700EQ This is an original replacement door panel that is a perfect reproduction made in Germany. Features: period correct material with the correct graining water resistant fiberboard base layer of sound absorption foam perforations are die cut for superior fitment made in Germany sold individually. 1 necessary per car. If you would like a set, the driver's side is part # 993555031700eq
$345.40
Make a selection 993555031700EQ This is an original replacement door panel that is a perfect reproduction made in Germany. Features: period correct material with the correct graining water resistant fiberboard base layer of sound absorption foam perforations are die cut for superior fitment made in Germany sold individually. 1 necessary per car. If you would like a set, the passengers side is part # 993555032700eq
$345.40
Make a selection 96463141000 Sold individually. 1 necessary per car.
From $108.90
Make a selection 96453705700SET If you are hearing a crunching or creaking noise when you close your door, start by replacing your door check / door arrester. It prevents the door from opening to widely or slamming. As our cars age, they wear out and start to become very noisy. We also recommend replacing the door check bolt, and safety clip, so we have created an complete set for one door - repair sold individually. Left of right side fitment. 2 needed per car.
$64.13
Make a selection FVD20703500 This oil cooler kit is a must for engines that are modified. It reduces oil temperature and protects the engine. This kit can lower operating oil temperature up to 60* f. Simple installation without cutting or modifying. High quality behr cooler ensures reliability without sacrificing a/c performance as kit is mounted clear of the front a/c condenser. Can be mounted on cars with or without air conditioning. Sold as a complete kit, ready for installation.
$2,981.74
Make a selection FVD33150010 Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set. 1 kit is necessary per car. Please note: we recommend this kit for race use, as noise may resonate inside the cabin during street use. For those that are concerned about the noise, please order part # FVD3310212291
$704.00
Make a selection FVD6314051US Now we can offer you quality clear turn signals. . They will not fade and discolor with time like those on the market in the past. The set includes 2 qty., 12v 21 watt us spec. Amber bulbs to meet road regulations. Sold as a set. 1 necessary per car. Please note: these are euro spec turn signals, so the flat side reflectors hole for the bulb holder is not cutout. Us customers can drill / dremel out the reflector and install their bulb holder and 2 qty. Bulb part # 99963113890 . Looking for a cost effective h4 euro headlight conversion? Check out our part # FVD63191101
$319.73
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$715.00
Make a selection FVD33396411 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of eibach pro kit springs. This suspension kit is meant for those who want the car to sit at the lowest possible ride height. This set up will allow you to lower the front axle by 2.4 inches (60 mm). This is a perfect kit for clubsport or race use where the surfaces are smooth and even. The stock rs ride height was 1.6 inches (40 mm) lower. So, this is a full 3/4 of an inch (20 mm) lower on the front axle. Sold as a complete kit. 1 kit is necessary per car. Please note: we recommend the b6 / ohlins suspension kits for those looking for more comfort for street use.
$2,616.16
Make a selection FVD5550011RSKEV Great detail is taken to attempt to match the original weave size, color and polish. Whether you are adding carbon to the interior or matching existing pieces, this is high quality and is made in Germany so it is made to last, like the original. Sold as a set.
$805.45
Make a selection FVD637010KEV German made polished carbon door lock set. Perfect finishing touch for an updated interior or for a replacement of the original plastic locks. Great detail is taken to attempt to match the original weave size, color and polish. Whether you are adding carbon to the interior or matching existing pieces, this is high quality and is made in Germany so it is made to last, like the original. Please note: you must re-use your factory center knob. If you would like to replace those as well, please order part # 9285375810370b and the cap is part # 91153170300. Sold as a set. 1 necessary per car.
$368.45
Make a selection FVD803993VS0222 High quality, German made three-point replacement safety belt, designed to perform like the original. Features / specs: belt length: 300 cm (118 inches) 3 point inertia reel belt angle adjustable reel (max. Of 8 *) includes 22 cm (8.5 inch) buckle, installation hardware and caps. Din-en-iso 9001: 2000 quality standard manufactured, e-mark approved. The matching rear belt is part # FVD803993hr sold individually. 2 necessary per car.
$162.80
Make a selection FVD90155550 This 8-piece set includes the a-pillar, b-pillar and c-pillar linings. Original leatherette material, sourced and manufactured in Germany. Each is cut, sewn and trimmed for precise fitment. Sold individually. 1 necessary per car.
$72.60
Make a selection HEI964001005S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar - screwed in to the original seat belt points chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Retains full seat adjustability. Semi-gloss black finish. Cost effective for club sport ...(choose a part on the right to read more)
$1,284.80
Make a selection FVD803993VR0222 High quality, German made three-point replacement safety belt, designed to perform like the original. Features / specs: belt length: 300 cm (118 inches) 3 point inertia reel belt angle adjustable reel (max. Of 8 *) includes 22 cm (8.5 inch) buckle, installation hardware and caps. Din-en-iso 9001: 2000 quality standard manufactured, e-mark approved. The matching rear belt is part # FVD803993hr sold individually. 2 necessary per car.
$187.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |