Vehicles
Sections
167 not categorized PORSCHE 930 PRESSURE PINCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 912 1965-69 (includes uncategorized and accessory items) BES99102240SHDO + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$4,383.50
Make a selection BES99120040S Take your 991.1 or 991.2 turbo or turbo s to a new level with these muffler bypass pipes. They produce the wildest sound available on the market today and are a perfect upgrade for level 3 or 4 car used on the track. They produce loud, low, deep tones with exaggerated turbo whistling and sinister gurgling and crackling off throttle. By far the best sound you can get out of your turbo, not to mention being able to shoot flames! The only real drawback is the drone in the cabin which we try to minimalize by stepping down the diameter in 3 stages. Features: - + 35 crank hp & + 25 crank torque - 3 tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage. - weighs 7 lbs. (3,1 kg) - German v2a - x5crni1...(choose a part on the right to read more)
$585.20
Make a selection BES99125010SK Are you one of those that are looking for more sound from your Porsche sport exhaust (pse)? Perhaps it's not quite as aggressive as you would like, or your last Porsche just sounded so much better? Don't worry, we have you covered, and the beauty is, you don't have to touch the catalytic converters which is a big no, no with Porsche dealers. With the valves open you receive a far more exotic, rich, deep, turbo motorsport tone and with the valves closed, soft subtle, completely stock sounds. So, absolutely no compromise and you will be thinking, the car really should have left the factory like this! Features: - + 10 crank hp & + 8 crank torque. - weighs 29 lbs. (13 kg) - German v2a - x5crni18-10 - 1.4301 stai...(choose a part on the right to read more)
$4,312.00
Make a selection BES99722040S81 Brombacher 997.2 tt "sport stock" stainless steel, cat bypass for OEM muffler facts: - + 21 crank hp & + 18 crank torque** - reuses OEM muffler, perfect for those looking for more sound and power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress - 6 on a scale of 1-10 in volume (1 being stock). - reuses OEM v band style connecting hardware. - made in Germany. - available in 100 cell or 200 cell. Please ask your sales person for pricing. - more distinguished growl at idle, partial throttle and wide open throttle. - dme programmin is necessary. - reuses OEM tips. FVD i...(choose a part on the right to read more)
$859.10
Make a selection BES99722240BES Brombacher 997.2 tt "sport " stainless steel, sport cat converter replacements for our bes- muffler facts: - + 21 crank hp & + 18 crank torque** - 200 cell "hd", tri metal German hjs sport catalysts - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress - 5 on a scale of 1-10 in volume (1 being stock). - reuses OEM v band style connecting hardware. - made in Germany. - available in 100 cell and cat bypass. Please ask your sales person for pricing. - more distinguished growl at idle, partial throttle and wide open throttle. - dme programming not necessary. - reuses OEM ti...(choose a part on the right to read more)
$4,303.20
Make a selection FVD0069118489 Decals are commonly overlooked when completing a restoration or refreshing the paint. They are often a key detail that sets a car apart when being judged at an event or being purchased by a keen aficionado. Contains: 1 qty. Valve clearance adjustment decal / sticker - 90100650300 1 qty. Engine oil level decal / sticker - 93000650402 1 qty. Tire / tyre pressure decal / sticker - 93770112700 1 qty. Firing order decal / sticker - 93000650901 sold individually. 1 is necessary per car. Did you know that we are restoration aficionado's at FVD? Be sure to browse the spare parts / restoration portion of our website to see what else we can help you with. If you don't see what you're looking for just give us a call. W...(choose a part on the right to read more)
$43.29
Make a selection FVD11691312 Quicker acceleration, leight weight. Kit contains the following part: pressure plate, disc, release bearing, flywheel,starter ring gear, guide tube, bolts. Clutch kit rated at up to 890 nm.
$3,168.25
Make a selection FVD1169013 Kit contains the following part: pressure plate, disc organic-torsion, release bearing, grease 260 nm
$1,264.89
Make a selection FVD123013 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection FVD116987 Hailing from the baden wurttemberg region in Germany, speaking the language and dealing with lead engineers from the OEM and motor sport manufacturers since 1984 has many advantages. This FVD exclusive clutch kit is culmination of zf sachs race engineering gmbh parts and an aasco motorsports lightweight flywheel that have been developed to work together without compromise. This kit offers a silky-smooth release, superb drivability, can handle more torque than comparable clutch kits. We specifically chose a clutch disc with torsion springs that function as a vibration damper between engine and gearbox that is necessary when removing the factory dual mass flyweel (dmfw). It also means that you will experience an ...(choose a part on the right to read more)
$2,638.90
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$2,976.60
Make a selection FVD123042ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection FVD123041ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection FVD33396401 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,538.69
Make a selection FVD33396400 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,708.92
Make a selection FVD12399600R Silicone boost hose kit FVD's direct replacement boost hose kit eliminates common boost hose "blow outs" on modified turbo's. Facts: tested to withstand over 75 psi (5 bar) boost pressure.fuel and oil resistanttemperature range between - 50 to + 180 degreesbolt on kit over time the OEM boost hoses tend to expand and contract under higher load, which leads to leaks, or "blow outs". Also, the OEM aluminum end does not secure properly into the intercooler, which causes boost leaks, and boost hose blowouts. Our machined billet ends are a perfect secure fit and our silicone hose is designed not to expand under boost pressure. The hose kit is a complete bolt on kit.
$590.70
Make a selection FVD3522P38056AS The brembo gran turismo s (gt-s) braking system is ideal for clubsport and sprint type track events. The GT-s type iii system utilizes brembo type iii aggressive face type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. Gt-s systems contain advanced calipers that include racing style radiators, dual inner piston seals, an inner pressure seal and an outer wiper seal. This innovative design provides the best combination of performance and long-lasting track use. The calipers are hard anodized in black (machined brembo logo in red) for resistance to corrosion and...(choose a part on the right to read more)
$4,174.50
Make a selection FVD50499101MM The moshammer side inlet set is a striking design that enhances performance and efficiency. The inlets create a ram air effect by scooping in a larger volume of air, which delivers up to 10% more air pressure into the intercoolers. These sets are available in satin black, gloss black or high gloss carbon. This is another versatile moshammer offering for a leased vehicle or for those looking to return the car to its original appearance in the future. This set complements the entire moshammer downforce rs (991.1 turbo/s) or evo rs (991.2 turbo/s) aero packages and benefits the mighty GT2 rs as well. Features: striking design increased performance added efficiency direct bolt on available in satin black, gloss bla...(choose a part on the right to read more)
$1,082.40
Make a selection FVDB2435500 FVD Brombacherstainless steel brake lines for Porsche are manufactured in europe and are approved for all abs systems. They consist of a ptfe teflon inner liner surrounded by a stainless steel (inox) braided cover. They are also coated in a uv resistant pvc jacket to protect the wire and inner hose from the elements, chemicals and abrasion. This construction ensures minimal expansion inside the hose core and eliminates that "spongy" brake feel that is commonly found in the OEM brake lines. FVD Brombacherhas been tuning Porsche vehicles for over 30 + years now, so rest assured that our lines are a direct bolt on replacement for each Porsche application. Our lines are DOT approved by conforming to the fmvss 1...(choose a part on the right to read more)
$158.40
Make a selection FVD36203400 Premium German made metal valve stem with a high quality seal to prevent leaking. Valve hole diameter: 11.3 mm (.44 inches) shaft: 5 mm (.47 inches) weight: 31 grams made in Germany sold individually. Please note: these are not meant to be used with tire pressure monitors or hollow spoked wheels.
$9.90
Make a selection FVDB7035500 FVD Brombacherstainless steel brake lines for Porsche are manufactured in europe and are approved for all abs systems. They consist of a ptfe teflon inner liner surrounded by a stainless steel (inox) braided cover. They are also coated in a uv resistant pvc jacket to protect the wire and inner hose from the elements, chemicals and abrasion. This construction ensures minimal expansion inside the hose core and eliminates that "spongy" brake feel that is commonly found in the OEM brake lines. FVD Brombacherhas been tuning Porsche vehicles for over 30 + years now, so rest assured that our lines are a direct bolt on replacement for each Porsche application. Our lines are DOT approved by conforming to the fmvss 1...(choose a part on the right to read more)
$169.40
Make a selection FVD72147951 The engine leakage tester drv 05 detects engine defects quickly. Inlet valve or outlet valve defects,piston/pistonrings defects,cylinder head gasket defects . Pressure of compressed air between 6 and 12 bar ! Made in Germany (hazet)
$485.10
Make a selection K1347 A good upgrade for slightly modified engines. Convert fuel injected 2.0 engines to weber 40 mm (40 idf) dual throat carbs. Each kit contains two carburetors, cast aluminum manifolds, fuel line, clamps and all necessary gaskets. The special mounting hardware for the linkage arms is made from an aluminum alloy casting that is much stronger and more rigid than a thin metal stamping. The throttle arms ride in individually adjustable heim (ball) joints for easier adjustment and smoother throttle response. This kit is for off-road and racing use only, and must never be used on the highways in california. When switching from fuel injection to carburetors, each kits require a lower-pressure fuel pump (part number run7...(choose a part on the right to read more) General Fitment914 1970-76912 1965-69
$1,150.00
Make a selection FVDB9135500 FVD Brombacherstainless steel brake lines for Porsche are manufactured in europe and are approved for all abs systems. They consist of a ptfe teflon inner liner surrounded by a stainless steel (inox) braided cover. They are also coated in a uv resistant pvc jacket to protect the wire and inner hose from the elements, chemicals and abrasion. This construction ensures minimal expansion inside the hose core and eliminates that "spongy" brake feel that is commonly found in the OEM brake lines. FVD Brombacherhas been tuning Porsche vehicles for over 30 + years now, so rest assured that our lines are a direct bolt on replacement for each Porsche application. Our lines are DOT approved by conforming to the fmvss 1...(choose a part on the right to read more)
$192.50
Make a selection FVD721801046 Flaig tire gauges are high quality German gauges that are the standard for accuracy in the industry. Measurements range from 0 to 55 psi (0 to 4 bar). Pressure is adjusted via fingertip release and the read out is held until released so that each tire can be perfectly adjusted. General FitmentALL
$48.40
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |