Vehicles
Sections
244 not categorized PORSCHE 356A MENS RINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 912 1965-69 (includes uncategorized and accessory items) 91511608705 On the flywheel side, the guide tube facilitates the movement of the thrust bearing in order to engage / disengage the clutch. On the gearbox side it provides a seal between the gearbox and driveshaft. These two functions are critical, so we recommend replacing the guide tube with any thrust bearing or clutch replacement. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
From $115.01
Make a selection 91442413100 Spring, 32 mm and 42 mm ends. Fits 356c, 911 1965-77, 912, and 914. interior shifter mechanism tension spring. keep your shifter operating at full efficiency the way it should with a brand new replacement. while replacing this, make sure to replace the shifter bushings at the same time for optimal results. View/Change Diagram
$5.00
Make a selection 91442321100 A worn bell crank bushing / bearing sleeve can cause binding. Several are commonly used on the accelerator pedal linkage. When they fail the pedal will bind up causing poor throttle response and a sticky pedal feel. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. View/Change Diagram
From $2.63
Make a selection 91163193900EQ If you are restoring or replacing a rear taillight, you may want to consider this. It is a lightweight, high-quality OEM replacement, designed to perform like the original. Perfect for a race application, or for a lightweight street car. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. Driver's side fitment. 1 necessary per car.
$320.10
Make a selection 93010734714 This part is sourced in Germany to ensure quality, reliability and precise fitment. This will fit all the vehicles listed in the fitment tab and those that have been updated to pressure fed tensioners. This line requires that you also purchase part # 93010734706 . We also recommend purchasing 1 qty. Union nut, part # 90010400303 and 1 qty. Cutting ring sleeve, part # n0208251 for installation. Also need the right side? Please order part # 93010734812 for the 911 3.2 l and 930 3.3l. Order part # 93010734815 for the 965 3.3 l. Sold individually. 1 necessary per car.
From $41.80
Make a selection 93010734706 This oil pipe is necessary when installing the oil line for the tensioner hose to camshaft carrier, part # 93010734714 we recommend purchasing, 1 qty. Banjo bolt n0210731 and 2 qty. Sealing rings, part # 90012311530 to complete the installation. This part is sourced in Germany to ensure quality, reliability and precise fitment. This will fit all the vehicles listed in the fitment tab and those that have been updated to pressure fed tensioners. Sold individually. 1 necessary per car.
From $24.75
Make a selection 93010501304 Genuine intermediate shaft and gear, sourced in Germany to ensure quality, reliability and precise fitment. We recommend ordering 6 qty. Oil pump lock plates part # 99903900100 for installation. Please note: please check the model fitment tab to ensure accurate fitment. Sold individually. 1 necessary per car.
From $1,612.60
Make a selection 93060290401A Distributor caps are often overlooked as the source of ignition issues. If yours is failing or cracked, you can experience shaking at idle, poor starting in the cold, stalling and backfiring. Be sure to replace it if you see any signs of cracking. This is a high-quality beru replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
From $26.40
Make a selection 930105136001 Genuine gear, sourced in Germany to ensure quality, reliability and precise fitment. We recommend ordering 6 qty. Oil pump lock plates part # 99903900100 for installation. Please note: please check the model fitment tab to ensure accurate fitment. Sold individually. 1 necessary per car.
$401.50
Make a selection 93012321001 Turbocharger wastegate membrane diaphram
$220.00
Make a selection 93021162201 Each hose sold seperately. These long-lasting aircraft quality heater hoses conduct only the hottest heat to the front of your Porsche, while providing flex during engine movement! Order 4 hose clamps as well! Fit under the car near the engine and connect between the heater control valve and the body. 60 x 330 mm View/Change Diagram
From $23.10
Make a selection 91110190170SET Oem (original equipment manufacturer) complete set of bearings that does not include #8, sourced in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$645.70
Make a selection 99334703104 If your outer tie rods are worn, you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod consists of: 1 qty. Tie rod 1 qty. Hexagon nut (m14 x 1.5) 1 qty. Inner axial joint 1 qty. Lock nut 1 qty. Dust bellows / boot we recommend replacing the right and left side tie rods at the same time. Sold individually. 2 necessary per car.
$216.29
Make a selection 99334101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install original control arm bushings. . Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part. Sold individually....(choose a part on the right to read more)
$418.00
Make a selection 91110190100EQ Aftermarket complete set of bearings that does not include #8, sourced in Germany. Sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$148.50
Make a selection 9A160410300EQ If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually, you will hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter, be sure to check the protection cap on the terminal for cracks which allows moisture in and causes pre-mature failure. High-quality denso OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$485.10
Make a selection 9A160410400EQ If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually, you will hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter, be sure to check the protection cap on the terminal for cracks which allows moisture in and causes pre-mature failure. High-quality denso OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$506.00
Make a selection 99960701000 Fuses protect your wiring and electrical equipment. If you notice that something is not working check your fuse box first. This is a direct replacement blade type fuse. We recommend traveling with a few spares. Sold individually.
$2.20
Make a selection 99970159640 High-quality victor reinz replacement o-ring. Victor reinz has been supplying German auto manufacturers and Porsche for decades. They are a trusted name in gaskets and sealing products. Sold individually. View/Change Diagram
From $1.00
Make a selection 96434307281ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$194.70
Make a selection 96433106080 Our spring plates are manufactured in europe by an OEM supplier to Porsche using the finest materials (high carbon steel, 7075 t6 aluminum and 65 shore rubber - oe spec). Sold individually. Right side fitment. 1 qty. Required.
$680.00
Make a selection 96433105980 Our spring plates are manufactured in europe by an OEM supplier to Porsche using the finest materials (high carbon steel, 7075 t6 aluminum and 65 shore rubber - oe spec). Sold individually. Left side fitment. 1 qty. Required.
$680.00
Make a selection 99310541906EQ Exhaust valve for 993 models from 1996-98 with m64.21/22/23/24 motors. 8 mm stem, 43.5 mm, weighs .22 lbs. (.1 kg). Sold individually. 6 necessary per car. When working on your cylinder head, we recommend replacing the valves, valve seat rings, guides, springs, retainers and temperature sensor at the same time to reduce future labor costs.
$73.70
Make a selection 90110113803 High-quality OEM (original equipment manufacturer) main bearing replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment. View/Change Diagram
From $165.00
Make a selection 964347009BXATK This steering rack is a remanufactured part with a core, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. The remanufacturing process includes full inspection and testing for structural integrity. We then disassemble and bead blast to remove corrosion. Internals are micro-finished to OEM specifications. Sealing surfaces are carefully checked and restored prior to installing new premium seals and o-rings. Each unit is then carefully tested for full functional...(choose a part on the right to read more)
$1,633.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |