Vehicles
Sections
214 not categorized PORSCHE BOXSTER BUSHINGSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 912 1965-69 (includes uncategorized and accessory items) FVD205993001VA H&r front sway bar with a 26 mm diameter. 2-way adjustable. This is the front sway bar from our kit, part # FVD205993001. Includes bushings. Sold individually. 1 needed per car.
$473.00
Make a selection 90110313101 This bushing is located in the small end of the connecting rod on the wrist pin side. Be sure to inspect and replace when refreshing the motor as worn wrist pin bushings can create piston slap which is inefficient and can cause engine damage. Sold individually. 6 necessary per car. View/Change Diagram
From $7.07
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection 99334101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install original control arm bushings. . Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part. Sold individually....(choose a part on the right to read more)
$418.00
Make a selection 99334101702ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install original control arm bushings. . Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part. Sold individually....(choose a part on the right to read more)
$418.00
Make a selection ER2051500 High performance bushing replacement, no squeaks! Want to experience precision driving, faster lap times, improved road feel and feedback? These patented elephant racing polybronze suspension bearings set a new standard for performance, ride quality and ease-of -installation. Polybronze have a rigid bronze bearing core that does not deform. The polyurethane jacket absorbs mount irregularities while the bronze inner bearing remains true, providing a free-moving machined-fit that rides on a precision race. provided grease fittings make re-lubrication a breeze and a figure 8 groove keeps grease in place. The combination delivers zero squeaks and friction-free suspension movement. well suited to street or track, ...(choose a part on the right to read more) General Fitment911 1965-69912 1965-69 914 1970-76 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$288.00
Make a selection 91142402404 Does your car have a broken or stripped shift coupler? a brand new coupler is the answer to your issues. if you have issues shifting into gear or catching the correct gear, try a new coupler. This is for a 911. Can also be used for a 914 by removing the black portion. View/Change Diagram
From $111.00
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 96434307181ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$194.70
Make a selection 96434101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 018 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 96434101707AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 017 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 99333105280 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $764.50
Make a selection 91442413100 Spring, 32 mm and 42 mm ends. Fits 356c, 911 1965-77, 912, and 914. interior shifter mechanism tension spring. keep your shifter operating at full efficiency the way it should with a brand new replacement. while replacing this, make sure to replace the shifter bushings at the same time for optimal results. View/Change Diagram
$5.00
Make a selection 91110190160EQ Oem (original equipment manufacturer) complete set of bearings (including # 8) sourced in Germany to ensure quality, reliability and precise fitment. Set includes: 1 qty. Crankshaft main bushing sleeve - bushing viii - oversize +0.25mm 12 qty. Crankshaft main bearing shells ii-vii (half) - oversize +0.25mm 2 qty. Crankshaft main bearing shells i (half) - oversize +0.25mm sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$692.05
Make a selection 90162892301 This is the female of the two required bushings per wiper shaft. easily installed with the rack removed. View/Change Diagram
From $15.81
Make a selection 901423015RB Tried to dismantle your pedal cluster to install new bushings and found that it is impossible to drive out the roll pin? Join the crowd! Time for a rebuilt cluster. All of our rebuilt clusters are completely dismantled, sand-blasted, painted, new parts used if needed, and reassembled with silicone bronze bushings. the only complete cluster available from anywhere! Includes brake light switch, brake push rod, throttle pivot, and rubber pedal pads. Ready to be installed! core charge...(choose a part on the right to read more) General Fitment914 1970-76911 1965-69 930 1975-77 911 1974-77 911 1970-73 912 1965-69
$425.00
Make a selection 90134379202
View/Change Diagram
From $7.57
Make a selection 90160342101 High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: for 911 models after 1975 this fits engine codes: 911.41/42/46/47/83 View/Change Diagram
From $26.00
Make a selection 90133300309 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on. Features: made from ¼ inch spring steel includes new OEM spec. (65 shore) rubber bushings made in Germany sold individually. Left or right-side fitment. 2 necessary per car. View/Change Diagram
From $306.90
Make a selection FVD10099902 With the roll bar camera mount and your video camera, you can have it all. 3-axis adjustment lets you capture any view - study strategies, document infractions, refine your technique, even tape yourself as you drive. Special vibration-absorbing urethane bushings assure a clear picture. No drilling required easy installation. Security strap included. General FitmentALL
From $157.94
Make a selection
$21.85
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |