PORSCHE 356 SEAL ENGINECan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 - Engine (includes uncategorized and accessory items)
$40.91
Make a selection 99610090394 All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$632.50
Make a selection 91150411302EQ This one-piece seal is furthest from the rear bumper, we recommend replacing this when removing the motor for maintenance. We recommend replacing both the small and large engine seals, the large is part # 91150411102 sold individually. 1 necessary per car.
$16.50
Make a selection 029105245B Easily installed especially when doing a clutch job, make sure you check the crankshaft end play and have the appropriate three shims in place. View/Change Diagram
From $14.00
Make a selection
$44.58
Make a selection
$23.10
Make a selection 99610090391 All motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$808.50
Make a selection
$12.54
Make a selection 99970711341 Note: only for o.e. Type steel tubes. View/Change Diagram
From $1.00
Make a selection 00004301000 View/Change Diagram
From $51.90
Make a selection
$123.30
Make a selection 9997071124A Oil return tube o-ring for genuine oil tube. Will not work on aftermarket tubes. Sold individually. View/Change Diagram
From $1.35
Make a selection 021101343A Do not let anyone tell you that you do not need these! you do and four of them. often you can hear one that has failed as it sounds like a wet sheet flapping in the wind as you drive by a highway divider with the window down. it also sounds like compressed air leaking in puffs when the engine is turned over to start. make sure that the sealing surface is smooth before installation. View/Change Diagram
$4.75
Make a selection 039129707 This is the intake block that fits in between the intake runner pipes and the head. critical for insulating the injectors from engine head and for sealing the intake system from vacuum leaks! Two required per car. View/Change Diagram
From $9.50
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 029198009 All of the gaskets and seals to completely rebuild your engine except for the front and rear main seals! this kit is specifically for the 1974-75 914 1.8 but contains only muffler gaskets for the 74 muffler. Also order four muffler gaskets if you have a 75 model with the factory heat exchangers. General Fitment914 1970-76
$95.99
Make a selection 039906031 Multi port injector includes fuel hose fuel injector View/Change Diagram
From $99.89
Make a selection 021119957 This is an autoatlanta exclusive oil pressure switch boot for all 914-4 models. believe it or not your 914 had this factory installed. long gone on most engines by now this part is critical to seal in the cooling air. easily installed, this part fits behind the distributor. please check the oil pressure switch for leaks at the same time. View/Change Diagram
$13.00
Make a selection FVD123014ATK K-16/24 turbo (up to 555hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbocharg...(choose a part on the right to read more)
$2,976.60
Make a selection 021101341A If you notice a strange oil leak at the base of your cylinders, this is the culprit! also used to space the cylinders when building a high performance engine. four required for all stock applications and multiples for high performance applications. View/Change Diagram
From $2.00
Make a selection FVD123014 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection FVD123041ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection 022101559S One of the most required and necessary-to-replace parts in any 914 engine rebuild. This plate is the seal that fits the baffle windage tray into the bottom of the engine case. Super high-temperature made from that latest silicone rubber technology. General Fitment914 1970-76
$17.38
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |