PORSCHE 911 ORDER PARTSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 - Engine (includes uncategorized and accessory items)
From $89.10
Make a selection 021119751 Connects to thermostat bellows and insures quick warmup. make sure that the thermostat is working properly as well collapsed when cold and expanded when hot. Remember that the cooling flaps spring open for maximum cooling when the thermostat wire breaks. order the other connecting parts as well. View/Change Diagram
From $23.85
Make a selection 021101397 This is the part that attached the rocker shafts to the head. They are very odd sized with a 7mm nut securing the rocker arm to the head. eight required, order valve cover gaskets and the 7mm nuts at the same time and inspect the valve adjusting lugs for damage. View/Change Diagram
$11.85
Make a selection QRS001 This fiberglass engine shroud is a great replacement for your missing or cracked factory piece. Note: this does not have the oil cooler duct; may not work with some models. Make sure to examine your existing shroud before ordering. This is a special order part. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76
$689.00
Make a selection FVD201911964993 Looking to update your fuel cap? This is a cost effective, sporty, aluminum alternative to the factory cap. It resembles the tequipment cap available on the water-cooled models. It is a quality tuning product manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Oem non-locking, screw type fuel cap sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary ...(choose a part on the right to read more) General FitmentACCESSORY
$136.40
Make a selection 113LM099FD Genuine bbs motorsport center cap finished in gloss black with a silver logo. This cap is used primarily on the bbs rs, rx, rm and le mans type 099 wheel.
$22.00
Make a selection 10050330000 This 9 inch front and 11 inch rear steel fender flare set is made in Germany, we offer a complete line of replacement bodywork to complement the entire Porsche model range. Sold individually. 1 necessary per car. Please note: for conversions, these flares will allow you to run 9 wide tires in the front and 11 wide in the rear. For the 964 / 965 models the torsion bar cut out must be filled. Due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$1,648.90
Make a selection 113915001 Genuine lightweight aluminum bbs motorsport valve stem. This is used predominantly on bbs motorsport wheels like the e30, e50, e26, e 28 and e88. It has a 28 mm length / 11-13 mm valve hole diameter. Bbs part # 09.15.001. Please check the fitment prior to placing your order. Sold individually.
$16.50
Make a selection 10055511176 Quality replacement perlon / felt carpet set manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to Porsche in Germany. Features: historically correct perlon / felt material original fitment molded / form fitted includes correct cut outs and button / snap holes manufactured in europe sold as a set of 3 pieces. 1 necessary per car. Please note: the cutout for the fuse box must be cut out separately.
$137.50
Make a selection 115000003 Support nut for our part # 115114 115115 and 115116 etc. Internal thread: 4.7cm total height of the ring: 2.2cm height of the upper part of the screw ring including the thread: 1.4cm sold individually
$38.50
Make a selection 1150002RE These are made with club sport events in mind. They work with stiffer springs and lowering springs (we recommend h&r or eibach) and have a fully threaded body for individual lowering like the original 993 cup suspension. Lowering is adjustable to 35 mm (1.37 inches) sold individually. For matching club sport shocks, please order part # 1150002re for the right and 2 qty. Part # 1150009 for the rear. For a properly spec'd complete kit including front and rear club sport shocks with lowering springs and rear drop links, please order part # FVD33399300.
$517.00
Make a selection 022906031A Our rebuilt fuel injection components are the highest quality available and replace no longer available parts. Your 914 fuel injection can again operate as it should for snappy performance, great gas mileage, and long engine life. View/Change Diagram
From $160.00
Make a selection 115000001 Support nut for our part # 115112 115113 115115 and 115116 etc. Internal thread: 4.7cm total height of the ring: 2.0cm height of the upper part of the screw ring including the thread: 1.2cm sold individually
$50.60
Make a selection 021105101CB When rebuilding, the deepest part of the engine always needs special attention. A precisely matching, crack-check and balanced crank is the solution to the highest oil pressure, least vibration and longest life. Order matched bearings for a precise fit. There is a core charge, which is refundable upon receiving your rebuildable part. General Fitment914 1970-76
$795.00
Make a selection 021101351B Our friends at high performance have come up with a very inexpensive way of buying 1.7 heads for your high performance applications. Remachined from commonly available 1.8 heads, these parts will give you 2.0 power at a fraction of the cost of factory 2.0 heads. This part requires a core charge, refundable upon receiving your rebuildable head General Fitment914 1970-76
From $460.00
Make a selection 021105101 When rebuilding, the deepest part of the engine always needs special attention. A precisely matching, crack-check and balanced crank is the solution to the highest oil pressure, least vibration and longest life. Order matched bearings for a precise fit. View/Change Diagram
From $316.25
Make a selection 10010303806 The 11.8:1 compression will provide you with more acceleration than kits with 11.3:1 compression. For track use we recommend more aggressive cam (maximum valve lift (tdc) of 2.1 mm) . Piston's has very deep pockets for use with sport valves. These are 107 mm in size so are slip fit and do not require modifications. This kit is ideal for track use but can also be used on the street, it will add 35+ hp (depending on your additional modifications). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resistance, they are nikasil coated which reduces wear and friction. We also have t...(choose a part on the right to read more)
$11,932.00
Make a selection 000043152124XR Genuine set of plush velour floor mats with nubuck edging that is custom tailored for your Porsche. Each is cut, sewn and trimmed to fit perfectly. They include a non-slip and waterproof rubber backing and are secured with a new updated fastening system. Limited availability due to color. If you don't see the color you require please contact an FVD parts specialist. Please note: these are for left hand drive models only.
From $204.08
Make a selection 1150002LI These are made with club sport events in mind. They work with stiffer springs and lowering springs (we recommend h&r or eibach) and have a fully threaded body for individual lowering like the original 993 cup suspension. Lowering is adjustable to 35 mm (1.37 inches) sold individually. For matching club sport shocks, please order part # 1150002re for the right and 2 qty. Part # 1150009 for the rear. For a properly spec'd complete kit including front and rear club sport shocks with lowering springs and rear drop links, please order part # FVD33399300.
$517.00
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 021198009D You can’t rebuild without an engine gasket kit, even if you are reusing the hard parts! Remember in addition to order four baffle plate seals, a front and a rear main seal and maybe a couple of cv joint gaskets! General Fitment914 1970-76
$76.56
Make a selection 039105101 When rebuilding, the deepest part of the engine always needs special attention. A precisely matching, crack-check and balanced crank is the solution to the highest oil pressure, least vibration and longest life. Order matched bearings for a precise fit. There is a core charge, which is refundable upon receiving your rebuildable part. General Fitment914 1970-76
From $391.50
Make a selection 1112P716059 Rennline's rubber grip aluminum pedal covers are the ultimate interior upgrade for any performance automobile. No other pedal on the market gives you the flexibility of adding and removing throttle extensions to fine tune your individual ergonomic preference. Rennline has taken this pedal design to the next level by utilizing rubber grips that can easily be replaced if needed. Each pedal set comes with 8 replacement rubber grips or can be purchased separately at any time. Rennline pedal sets are constructed of anodized aircraft grade aluminum and all stainless-steel hardware. Sold as a set of 4 pedals. Please note: gas pedal heel + toe extensions are sold separately. Please enquire. Order part # 1112 pe7071 fo...(choose a part on the right to read more)
$242.00
Make a selection 170211033SS This is a high-quality replacement heat exchanger manufactured by dansk. It is manufactured in stainless steel. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk930100 sold individually. Right or left side fitment. 2 necessary per car.
$1,144.00
Make a selection 190731901 Convert your current electrical mirrors to the factory aero mirror look available after the 1992 models. This kit will allow you to use your existing flag style mirror electrical motor to save cost. These parts are not factory reproductions, they are original parts. Quality is 100% factory. Please note: does not include adjusting motor. You would either reuse yours or must purchase it separately.
$1,694.54
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |