PORSCHE 356 B CONTROL CAMCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 - Front Axle/Steering (includes uncategorized and accessory items)
From $15.90
Make a selection 91433153304 Wonder why your rear wheels are out at the bottom and in at the top? The swing arms have twisted, the springs have sagged and/or the rear end needs alignment! Get the negative camber removed (each mm reduces negative camber by 10 minutes). Listing is for one 3mm shim plate. View/Change Diagram
$15.90
Make a selection
From $15.90
Make a selection BBI9974010001 Features
$1,895.00
Make a selection BBI9964010006 Finally, a solution that allows you to safely increase without the risk of damaging your front axles. as you add GT3 shims to your front Porsche 996/997 turbo lower control arms, you move the cv joints beyond their safe range of motion, risking failure and expensive damage. These 10mm thick precision spacers, used with 16mm of lca shims will provide an additional -1.7 deg. Of camber, while maintaining the factory cv joint and axle relationship. the spacer design features a concentric lip that positively and accurately locates it to the cv joint for perfect balance and no vibration. Each kit includes two spacers and all the needed hardware in high class 10.9 grad
$375.00
Make a selection FVD33150045 Original rubber replacement bushing (65 shore hardness value) for the rear control arms (camber link and caster link). This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$64.90
Make a selection ER911MNT If you need more front camber adjustment range, these elephant racing offset camberplates are for you. the monoball and mounting holes are offset, allowing up to 3/4 degree of additional camber adjustment range. just the ticket for your race car. These plates use the same spherical bearing technology as our front monoball cartridges and replace the entire factor camberplate. For even more negative camber, combine with our de-cambered ball joints. Combine with polybronze control arm bearings to achieve a rigid front suspension geometry that maintains alignment under hard braking and cornering loads. General Fitment914 1970-76
$499.00
Make a selection ER2081500 Need more camber?elephant racing de-cambered ball joints provide up to 3/4 degree additional negative camber per side. track is widened up to 1/2 inch. The ball joint stud is non-concentric with the housing, effectively lengthening the control arm and pushing the bottom of the strut (and tire) out resulting in added negative camber. Construction includes a true spherical bearing monoball for low-friction, freedom of movement and zero deflection. fully weather-sealed, de-cambered ball joints are a true bolt-in using factory ball joint hardware. General Fitment911 1970-73911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76
$470.00
Make a selection BBI9964010002 Finally, a complete solution to properly widen the front track width of a Porsche 996 and 997 turbo. To help increase front end grip, this kit allows full negative camber adjustment without binding the axles and fitment of wider wheel/tire combinations and GT3 cup car fenders. Each kit includes lower control arms, thrust arms, axle spacers, upper mounts, and camber shims.
$3,695.00
Make a selection FVD33150045R Replace worn-out soft rubber (65 shore hardness value) control arm bushings (camber link and caster link) with sportier rubber (75 shore hardness value) that is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$69.30
Make a selection
© 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |