PORSCHE 356B CAR MATSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 - Transmission (includes uncategorized and accessory items) 90134722303R The original rubber bushing is proven to be a weak link that can fail prematurely, allowing chassis geometry to be compromised. Symptoms include suspension movement during acceleration, braking and cornering. The powerflex black series bushing is manufactured of a more dense rubber than the original. It is a 95 shore compound that is more resistant to load than standard rubber which provides better control of chassis geometry for track use. Features: designed for track use improved track handling more precise and accurate alignment constant steering geometry increased tire life better steering feedback longer service life of suspension components less nvh (noise vibration hardness) than polyurethane bushings pl...(choose a part on the right to read more)
$37.40
Make a selection 44404480062 High quality polished center console set that includes a polished carbon handbrake, the upper switch and lower switch covers made ready for installation. Each piece is a carbon overlay, meant to be adhered to your original plastic trim covers. We recommend adhering the carbon overlays to your originals with würth bond and seal (sold separately).
$1,460.80
Make a selection 96434705804SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)
$196.90
Make a selection 911561051012EQ This is the top outer section of the cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers are made for modern electric tops with stronger frames for the 911 and 964. Sonnenland high quality material was originally used by Porsche and other top German manufacturers. Made in Germany. This would replace original part # 911 561 051 012xw sold individually. 1 necessary per car. Only f...(choose a part on the right to read more)
$1,141.80
Make a selection 9117310316003 Quality German aftermarket replacement for original part # 911 731 031 60. This is designed to perform like the original and is made from period correct material. Sold individually. 1 necessary per car. Please note: drivers side sun visor for a left-hand drive car only (lhd). The matching right side is our part # 9117310326003
$112.20
Make a selection 911561053003EQ Rear window cabrio top section, manufactured in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers for the mechanically operated tops. Sonnenland high quality material was originally used by Porsche and other top German manufacturers. Made in Germany. Sold individually. 1 necessary per car.
$984.50
Make a selection 9117310326003 Quality German aftermarket replacement for original part # 911 731 032 60. This is designed to perform like the original and is made from period correct material. Sold individually. 1 necessary per car. Please note: drivers side sun visor for a left-hand drive car only (lhd). The matching right side is our part # 9117310316003
$112.20
Make a selection 445552159001 High quality polished tray complete with rubber insert. Great detail is taken to attempt to match the original weave size, color and polish. Whether you are adding carbon to the interior or matching existing pieces, this is high quality and is made in Germany so it is made to last, like the original. Sold individually.
$547.38
Make a selection 47070901 Bmc sport air filters were originally developed in association with the ferrari f1 team. Bmc is one of the most recognized brands in the automotive industry and is the most successful filter in many types of racing. Oem filters only require a total particle filtration efficiency up to a minimum size of 10 microns. Oem air filters function primarily to protect the engine, so they are cost effectively produced in paper. Paper filters have high resistance to airflow that reduces the inlet pressure and consequently engine performance. A bmc sport filter contains an outer epoxy coated alloy mesh with internal layers of cotton gauze that have been immersed in a low viscosity oil. That technique ensures protection fro...(choose a part on the right to read more)
$214.50
Make a selection 444552985051 This is a carbon overlay, meant to be adhered to your original plastic instrument trim. We recommend adhering the carbon overlay to your original with wurth bond and seal (sold separately). Great detail is taken to attempt to match the original weave size, color and polish. Whether you are adding carbon to the interior or matching existing pieces, this is high quality and is made in Germany so it is made to last, like the original. This cover is a carbon overlay to be adhered to the original black plastic piece, part # 911 552 550 00 700 for reference. Sold individually.
$640.20
Make a selection 47041616 Bmc sport air filters were originally developed in association with the ferrari f1 team. Bmc started producing their filters in 1973 and is one of the most recognized brands in the European automotive industry, they are also a member of the vdat German tuning association. Oem filters only require a total particle filtration efficiency up to a minimum size of 10 microns. Oem air filters function primarily to protect the engine, so they are cost effectively produced in paper. Paper filters have high resistance to airflow that reduces the inlet pressure and consequently engine performance. Bmc filtration systems yield more engine performance, both in terms of power and torque without compromising reliability. A bm...(choose a part on the right to read more)
$117.70
Make a selection 44455298599RL This set includes a high quality instrument surround, radio cover, ignition cover, and glove box covers. Each piece is a carbon overlay, meant to be adhered to your original plastic trim covers. We recommend adhering the carbon overlays to your originals with wurth bond and seal (sold separately). Great detail is taken to attempt to match the original weave size, color and polish. Whether you are adding carbon to the interior or matching existing pieces, this is high quality and is made in Germany so it is made to last, like the original. Sold as a complete set. Please note: this is for cars without air bags!
$3,668.50
Make a selection BES98115000S This is a forum favorite for the best sound with minimal drone! This muffler really does everything so well. Civilized while cruising, a beast under load and cup car gurgles and crackles off throttle. + 11 hp & + 10 tq gain. - weighs 35.4 lbs - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 1/2 tubing (63.5 mm). - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin (200 rpms worth) compared to the competition's mufflers. This can be verified on the forums like ...(choose a part on the right to read more)
$3,314.30
Make a selection BBI9912020003 The bbi autosport 997 & 991 GT3 / rs exhaust side bypass is a direct replacement for the factory primary side mufflers. The primary mufflers are weigh approximately 44 pounds total while the bbi pipes are 4 pounds in comparison. For durability and protection against corrosion, each system is meticulously tig welded using 304 aerospace grade stainless tubing with lower carbon content. The result is a substantial reduction in weight behind the rear axle which significantly improves handling and less restriction to produce a much more aggressive exhaust note.
$950.00
Make a selection 96455550800EQ A-pillar lining made of original leatherette material, sourced and manufactured in Germany. Each is cut, sewn and trimmed for precise fitment. We go to extra lengths to ensure that our linings are as similar to the originals as possible. Replaces original part # 964 555 508 00 05t made in Germany. Sold individually. 1 necessary per car.
$94.60
Make a selection BEC911930BB Brombacher exclusive covers are completely manufactured in the south of Germany in baden wurtemberg, between stuttgart and our local mountains in the southern black forest. The materials chosen is environmentally friendly production and each stich is made with care. 100% Germany quality, perfect, personalized appearance for every taste, even in the covered state a mixture of cotton and polyester nano-coated on the outside which makes it so dirt and water repellent, completely paint-friendly, with very breathable construction. Price includes: cover color selection, color selection of trim, custom embroidered logo and a matching bag with a small custom logo, in the same colors. Please let us know what model, year...(choose a part on the right to read more)
$793.10
Make a selection BES99305040S FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts are manufactured in Germany and are tested comprehensively for flow rate and characteristics, thermal stress, resistance to cracking, and longevity. Brombacher mufflers outer shell dampens and eliminates unwanted frequencies and ensures no resonance or drone in the cabin. The end result is a strong, linear, firing-order dominated flat-6 Porsche sound. In addition, Brombacherexhausts systems are available for ultimate performance full titanium. Our titanium system's are nearly...(choose a part on the right to read more)
$1,820.50
Make a selection BES99725060SR Brombacher sport muffler for 997.2 GT3 / rs (sound version) with rsr style tips facts: - + 10 crank hp & + 10 crank torque - 2 3/4 tubing (70mm) straight through design for max. Power - weighs 28 lbs. (12.7 kg) - replaces stock side mufflers and stock center muffler - 36 lbs (16.3 kg) savings over stock system! - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability - 2 x 3.5 (90mm) rsr angle cut tips - includes all necessary clamps and mounting brackets - made in Germany - 105 db - intoxicating cup car growl at idle, partial throttle and wide open throttle - no interior resonance - no dme programming necessary, does not alter emissions, 50 state legal in the u.s. For reference: 997 GT3 OEM ...(choose a part on the right to read more)
$3,023.90
Make a selection 964564201007EQ This is the perforated sunroof lining, it is made in Germany with original material. It is as close to the original as possible and is cut and trimmed to fit perfectly. This part replaces original part # 964 564 201 007 00 sold individually. 1 necessary per car.
$127.60
Make a selection 96433105980 Our spring plates are manufactured in europe by an OEM supplier to Porsche using the finest materials (high carbon steel, 7075 t6 aluminum and 65 shore rubber - oe spec). Sold individually. Left side fitment. 1 qty. Required.
$680.00
Make a selection 96434703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. This is ideally suited for use with our monoball inner tie rod, part # 96434705805sp for the 964 c2 / turbo look or 965 or part # 96434705804sp for the 964 c4 or rs. Please note: this is not for the wide body. Sold indiv...(choose a part on the right to read more)
$322.21
Make a selection 96437502301ATK Send us your OEM transmission mount bracket and we will restore it to better than new condition! Our service includes removal of the old mount, media blasting, proper installation of the new mount and protective seal coating. Our mount is remanufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Simply order and send us your OEM bracket, we will take care of the rest. Approximate lead time is estimated between 3-6 weeks.
$178.20
Make a selection 98656300501 Special order factory hardtop. Snugfitting aluminum top has a heated rear window and fabric roof lining. Painted to exactly match your Boxster. Provide color code from your car and allow 2-3 weeks for delivery. Truck freight.
$3,805.15
Make a selection 96534703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM part number, 965 347 032 00. Sold individually. 2 needed per car. We also suggest replacing your inner tie rod, we have a uniball option, our part # 96434705805sp (qty. 1 is needed) and now is also a good time to replace your worn out inner tie...(choose a part on the right to read more)
$251.90
Make a selection 96433106080 Our spring plates are manufactured in europe by an OEM supplier to Porsche using the finest materials (high carbon steel, 7075 t6 aluminum and 65 shore rubber - oe spec). Sold individually. Right side fitment. 1 qty. Required.
$680.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |