Vehicles
Sections
224 not categorized PORSCHE 944S EXHAUST GASCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 (includes uncategorized and accessory items) FVD99710012M +27 crank hp & +22 crank tq gain on the 997.1 3.6 l, while offering ultra-smooth drivability and reliability that you expect from your Porsche. Package includes: - FVD my genius handheld flash tool (included). - FVD tuning software - part # FVD99761810mg - bmc sport filter - part # 47015601 - FVD m&m exhaust gmbh - sound version muffler - part # bes99715001s1 - FVD headers - part # 210111997 - FVD header and muffler installation kit - part # FVDmk997200 and part # FVDmk997001 FVD level 2 tuning: max. Power - 259kw (352hp) @ 7000rpm max. Torque - 400nm (295lbf ft) @ 4500rpm max. Speed - 300km/h max. Rpm - 7500rpm acceleration 0-100km/h (0-62.5 mph)* - 4.7s genuine: engine - 6 cylinder boxer capacity - 3596ccm co...(choose a part on the right to read more)
$6,056.60
Make a selection AP958170 Agency power is proud to release its super sport exhaust system for the 958 Porsche Cayenne s v8 2011 and up. the super sport exhaust is a axle system that gives your 4.8l v8 engine a real aggressive tone. made here in the usa, the exhaust saves close to 30lbs off the rear end of the vehicle. using 304 stainless steel and detail oriented tig welding, the exhaust system uses two small high flow mufflers which give it the sports car rumble. its reduced back pressure design gives the engine improved horsepower and torque with most noticeable improvement in throttle response. because of the reduced restriction, this exhaust horsepower gains can definitely be noticed in the mid to top rpm range.
$1,495.95
Make a selection 91411600001 Our 18-piece clutch package contains everything we use in our shop for a perfect clutch replacement. beware of lesser kits, you will need all of these parts! Included is the clutch installation manual. Kit includes: rear main seal, throwout bearing, 2 throwout bearing clips, flywheel, front trans. Seal, 2 cv joint gaskets, flywheel o-ring, ball stud cup, 2 muffler gaskets, needle bearing, cv joint bolt, clutch alignment tool, flywheel crush washer, felt washer, pressure plate, clutch disc, clutch installation manual. General Fitment914 1970-76
$924.32
Make a selection BES99710200SKGT - equal length headers with long tube design - 200 cell German hjs hf sport catalysts with u torque design - 2 3/4 tubing (70mm) - rsr style connections and quick release clamps - quad 3.5 (90mm) round tips - made in Germany -+ 21 hp & + 12 lb.-ft torque gain with exhaust system only. - weighs 62 lbs.(28,0 kg). Please note: this exhaust is a special order item ! Typically lead time is 2-3 weeks from Germany. Performance gains (includes FVD software, sport airfilter and exhaust):, based on the 3.8 l: max. Power - 283kw (385hp) @ 6500rpm max. Torque - 441nm (325lbf ft) @ 4000rpm max. Speed - 307km/h max. Rpm - 7900rpm acceleration 0-100km/h - 4.4s our Brombachersystem uses 2 ¾ inch (70mm) tubing and is modula...(choose a part on the right to read more)
$9,220.20
Make a selection BES99115000SKR + 11 hp & + 10 tq gain. - 2 3/4 tubing (70mm). - 18 lb. (8.5 kg)weight savings over OEM center muffler. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - replaces OEM center muffler and connects to OEM header and OEM side mufflers and OEM tips. Please note: this muffler is a direct replacement the 991 Carrera s (3.8l - us model) which comes standard with valves. It is also a direct replacement for the Porsche sport exhaust option. This center muffler bypass for the 991 is one of the most technically advanced for Porsche t...(choose a part on the right to read more)
$3,713.60
Make a selection RES98100000S A track favorite due to its performance gains and reliability. + 30 hp & + 25 tq gain. - catalytic bypass for track use. - weighs 59 lbs. (27,0 kg), OEM weighs 84 lbs. (38kg). - motorsport merge collector. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport muffler connections with a single gasket and flange at the header to ensure a leak free exhaust. - ecu programming (software) is necessary. The FVD Brombacherfull race exhaust system for the 981 and is one of the most technically advanced systems for Porsche to date. Our entire "brombacher" line of exhausts is manufactured to ou...(choose a part on the right to read more)
$5,710.10
Make a selection GR2012 Lubro moly lm 508 prevents seizing, galling and corrosion of threaded components and parts that are exposed to extreme temperatures. Insures accurate torquing during screw down. Permits destruction free disassembly later on! Lm 508 is an absolute must for exhaust parts, brake pad pins, and hardware. General FitmentACCESSORY
$6.85
Make a selection BES99725060SR Brombacher sport muffler for 997.2 GT3 / rs (sound version) with rsr style tips facts: - + 10 crank hp & + 10 crank torque - 2 3/4 tubing (70mm) straight through design for max. Power - weighs 28 lbs. (12.7 kg) - replaces stock side mufflers and stock center muffler - 36 lbs (16.3 kg) savings over stock system! - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability - 2 x 3.5 (90mm) rsr angle cut tips - includes all necessary clamps and mounting brackets - made in Germany - 105 db - intoxicating cup car growl at idle, partial throttle and wide open throttle - no interior resonance - no dme programming necessary, does not alter emissions, 50 state legal in the u.s. For reference: 997 GT3 OEM ...(choose a part on the right to read more)
$3,023.90
Make a selection FVD98010001 Kit includes: 2 x sport motronic dme (ecu) exchange 2 x sport airfilter genuine: engine - v10 cylinder capacity - 5733ccm compression ratio - 12,0:1 max. Power - 450kw (612hp) @ 8000rpm max. Torque - 590nm @ 5750rpm max. Speed - 330km/h max. Rpm - 8400rpm acceleration 0-100km/h - 3.9s tuning: max. Power - 478kw (650hp) @ 8000rpm max. Torque - 640nm @ 6000rpm max. Speed - 340km/h max. Rpm - 8600rpm acceleration 0-100km/h - 3.8s our Carrera GT ecu programming offers you not only more power and torque but phenomenal sound! Within the cgt end muffler is a flap-type mechanism fitted which is controlled by vacuum units. These vacuum units are also controlled by the ecu. Our programming modifies the control of these f...(choose a part on the right to read more)
$7,594.36
Make a selection FVD95761890MG Factory: engine - v8 twin-turbo capacity - 4806ccm compression ratio - 10,5:1 max. Power - 368kw (500hp) @ 6000rpm max. Torque - 700nm (516 lbf ft) @ 2250-4500rpm max. Speed - 275km/h max. Rpm - 6500rpm acceleration 0-100km/h - 5.1s tuning:* max. Power - 397kw (540hp) @ 6000rpm max. Torque - 780nm (575 lbf ft) @ 3500rpm max. Speed - 280km/h max. Rpm - 6700rpm acceleration 0-100km/h - 5.0s * only with sport exhaust system and sport air filter for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, ...(choose a part on the right to read more)
$1,094.50
Make a selection FVD424054 The perfect complement for a numeric racing short shift upgrade or a factory cable replacement. These numeric racing cables are motorsports quality that enhance the driving experience by providing a direct, mechanical connection to your car. They provide precision gear engagement that works seamlessly with the numeric racing short shift upgrade. Features: larger diameter steel spiral wound cable direct connection to each shift greater reliability precise engagement pre-lubricated for smooth operation billet aluminum and stainless-steel connectors eliminates excessive cable backlash for longevity billet aluminum rod ends thermo plastic jacket warranty included please note: professional installation is recommende...(choose a part on the right to read more)
$527.99
Make a selection FVD424052 The perfect complement for a numeric racing short shift upgrade or a factory cable replacement. These numeric racing cables are motorsports quality that enhance the driving experience by providing a direct, mechanical connection to your car. They provide precision gear engagement that works seamlessly with the numeric racing short shift upgrade. Features: larger diameter steel spiral wound cable direct connection to each shift greater reliability precise engagement pre-lubricated for smooth operation billet aluminum and stainless-steel connectors eliminates excessive cable backlash for longevity billet aluminum rod ends thermo plastic jacket warranty included please note: professional installation is recommende...(choose a part on the right to read more)
$535.69
Make a selection FVD424049 The perfect complement for a numeric racing short shift upgrade or a factory cable replacement. These numeric racing cables are motorsports quality that enhance the driving experience by providing a direct, mechanical connection to your car. They provide precision gear engagement that works seamlessly with the numeric racing short shift upgrade. Features: larger diameter steel spiral wound cable direct connection to each shift greater reliability precise engagement pre-lubricated for smooth operation billet aluminum and stainless-steel connectors eliminates excessive cable backlash for longevity billet aluminum rod ends thermo plastic jacket warranty included please note: professional installation is recommende...(choose a part on the right to read more)
$563.20
Make a selection FSPOR992SC Purchase disclaimer: fabspeed motorsport does not condone the use of emission defeat devices for any vehicles used on public streets or roadways. Fabspeed motorsport will not tamper, remove, disable, or bypass emissions equipment on a motor vehicle in accordance with 40 cfr section 86.1854.12(a)(3), clean air act 40 cfr 1068.101(b). This includes software, known as tunes, that reprogram a motor vehicles electronic control module to alter engine performance and enable the removal of filters, catalysts, and other critical emissions controls.
$3,695.95
Make a selection BES99125040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 25 hp & + 19 torque* - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes new clamps and muffler straps.* - made in Germany. - modular design for future 100 cell, 200 cell or cat bypass use. - more distinguished ...(choose a part on the right to read more)
$2,655.40
Make a selection BES99722240BES Brombacher 997.2 tt "sport " stainless steel, sport cat converter replacements for our bes- muffler facts: - + 21 crank hp & + 18 crank torque** - 200 cell "hd", tri metal German hjs sport catalysts - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress - 5 on a scale of 1-10 in volume (1 being stock). - reuses OEM v band style connecting hardware. - made in Germany. - available in 100 cell and cat bypass. Please ask your sales person for pricing. - more distinguished growl at idle, partial throttle and wide open throttle. - dme programming not necessary. - reuses OEM ti...(choose a part on the right to read more)
$4,303.20
Make a selection FVD99661831MG Genuine: engine - 6 cylinder boxer capacity - 3600ccm compression ratio - 11,7:1 max. Power - 265kw (360hp) @ 7200rpm max. Torque - 370nm (273lbf ft) @ 5000rpm max. Speed - 302km/h max. Rpm - 7600rpm acceleration 0-100km/h - 4.8s tuning: max. Power - 276kw (375hp) @ 7000rpm max. Torque - 390nm (288lbf ft) @ 5000rpm max. Speed - 310km/h max. Rpm - 7900rpm acceleration 0-100km/h - 4.6s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, making substantial gains in horsepower and torque, while re...(choose a part on the right to read more)
$1,204.50
Make a selection 220110981001 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)
$1,479.50
Make a selection BES99125020SK No need for Porsche sport exhaust (pse) envy with this muffler! This offers weight savings and a far more exotic sound than the pse, all without drone. It is the perfect compromise for you and your loved ones. Rich, deep, turbo motorsport tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english and is the best choice for a daily driver. Features: - + 16 crank hp & + 15 crank torque. - weighs 37 lbs. (17 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - direct bolt on replacement for the factory center muffler. - includes necessary installation hardware. - reduces turbo lag, backpressure and thermal lo...(choose a part on the right to read more)
$4,651.90
Make a selection BES99120040S Take your 991.1 or 991.2 turbo or turbo s to a new level with these muffler bypass pipes. They produce the wildest sound available on the market today and are a perfect upgrade for level 3 or 4 car used on the track. They produce loud, low, deep tones with exaggerated turbo whistling and sinister gurgling and crackling off throttle. By far the best sound you can get out of your turbo, not to mention being able to shoot flames! The only real drawback is the drone in the cabin which we try to minimalize by stepping down the diameter in 3 stages. Features: - + 35 crank hp & + 25 crank torque - 3 tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage. - weighs 7 lbs. (3,1 kg) - German v2a - x5crni1...(choose a part on the right to read more)
$585.20
Make a selection RES99701061S Race headers 997 GT3 cup, stainless steel - + 10 crank hp & + 8 crank torque - total weight is 14.1 lbs. (6,4 kg) FVD is proud to introduce our newest line of Brombacherrace exhaust systems. Brombacher race exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts are manufactured in Germany and are tested comprehensively for flow rate characteristics, thermal stress, resistance to cracking, and longevity. To further ensure quality, this race system meet's the standards of the fia and is registered with them directly. In addition, Brombacherrace exhausts systems are available for ultimate performance full titanium...(choose a part on the right to read more)
From $2,985.40
Make a selection BES99105040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 15 hp & + 12 torque - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes cone and v band style hardware to prevent exhaust leaks. - made in Germany. - modular desi...(choose a part on the right to read more)
$2,920.50
Make a selection BES99105060S - + 12 crank hp & + 12 crank torque - 2 3/4 tubing (70mm) straight through design for max. Power - weighs 18 lbs. (8.5 kg), which is a 3 lbs. Savings off of OEM center muffler. - replaces stock side mufflers and stock center muffler. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 2 x 3.5 (90mm) round tips. - includes all necessary clamps and mounting brackets. - made in Germany. - intoxicating cup car growl at idle, partial throttle and wide open throttle. - no dme programming necessary, does not alter emissions, 50 state legal in the u.s. Our 991 GT3 center muffler replacements are vastly different than the baffle plated mufflers stuffed with packing that are common in the after...(choose a part on the right to read more)
$2,337.50
Make a selection BES96405000S1 This muffler produces a glorious flat six race car with low deep tones that reminds us of the 964 cup. It is manufactured in Germany by m&m exhaust, gmbh. This muffler is ideal for anyone who wants a lower deeper tone with more decibels, whether they are just replacing the side muffler or are running cat bypass, sport cats or a cup pipe. + 14 hp (10 kw) & + 15 tq (20 nm) gain. - 2 3/4 tubing (70mm). - weighs 13.8 lbs (6.3 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions. - includes factory style hangars and new aero quip style clamps for simple installation. We recommend replacing your exhaust tip with this u...(choose a part on the right to read more)
$1,438.80
Make a selection BES99110200SK1 "brombacher" stainless steel sound switch exhaust system complete for the 991 3,4l. + 25 hp & + 20 tq gain. - 200 cell hjs "hd" sport catalysts. - 25 lb. Weight savings over OEM system (weighs 59 lbs. (27,0 kg), OEM weighs 84 lbs. (38kg). - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - motorsport merge collector. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport connections without gaskets or flanges to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. Please note: the 991 Carrera s (us or canadian model) comes standard with valves! Power...(choose a part on the right to read more)
$9,556.80
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |