Vehicles
Sections
26 not categorized PORSCHE 924 S INJ LINECan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 (includes uncategorized and accessory items) 99951225502 This is the common non intrusive hose clamp for all 7 mm id fuel line common on the Porsche 914. Hard to install but factory required as not to hurt the hose and cause a fuel leak! norma 13 View/Change Diagram
$3.23
Make a selection 043133387 Authorized by the factory in the "ho" campaign, these elbows replace the cloth covered ones affixed to your injectors. (cut off the old crimped fitting with wire cutters or a hacksaw blade and replace with a factory hose clamp) impervious to battery acid, these are the final solution to fuel leaks. sold each. General Fitment914 1970-76
$11.83
Make a selection FVD11091111002
$266.11
Make a selection RESMK911002 This kit is necessary when installing any of our racing / street exhaust systems manufactured by m exhaust gmbh whose part number begins with res 911 or bes 911 kit contains: - modified oil lines - straps - header / heat exchanger gaskets - additional heating hoses - air injection plug
$525.07
Make a selection K1347 A good upgrade for slightly modified engines. Convert fuel injected 2.0 engines to weber 40 mm (40 idf) dual throat carbs. Each kit contains two carburetors, cast aluminum manifolds, fuel line, clamps and all necessary gaskets. The special mounting hardware for the linkage arms is made from an aluminum alloy casting that is much stronger and more rigid than a thin metal stamping. The throttle arms ride in individually adjustable heim (ball) joints for easier adjustment and smoother throttle response. This kit is for off-road and racing use only, and must never be used on the highways in california. When switching from fuel injection to carburetors, each kits require a lower-pressure fuel pump (part number run7...(choose a part on the right to read more) General Fitment914 1970-76912 1965-69
$1,294.92
Make a selection K297 Progressive carburetor w/electric choke redline 32/36 progressive carburetor conversion. Kit comes complete with new 32/36 dfev carburetor, manifold, linkage, chrome air cleaner, hardware kit and fully illustrated instructions. This kit is for off-road and racing use only, and must never be used on the highways in california. When switching from fuel injection to carburetors, each kits require a lower-pressure fuel pump (part number run7304815) and a different distributor (part number r0231178009) General Fitment914 1970-76912 1965-69
$655.54
Make a selection 906632 All momo steering wheels require the use of a hub adapter. This is because each wheel is a universal wheel and the correct spline is required to fit different manufacturers. It s also important to set the wheel at the correct distance from the driver and clearance for things like the wiper and turn signal stalks. General Fitment356 1960-65911 1970-73 911 1965-69 912 1965-69 914 1970-76
$129.06
Make a selection MB24287 This is one of the most important diagnostic gauges for your 914. Especially for 914 2.0 fuel injected models, owners of which are lucky enough to have factory original adjustable fuel pressure regulators. Now you can see the benefit of your tuning efforts. Easily splices into the existing rubber fuel lines. The ends of the adapter are a little larger than stock to ensure a snug fit. Tapered adapter prongs can be slightly filed away to simplify your installation. We recommend lubricating the adapter ends for an easy insertion. The fuel pressure gauge installs right into the adapter. Use teflon tape for the gauge threads. Set includes 0-100 gauge (picture shows 0-15 which is incorrect), adapter, and two hose cla...(choose a part on the right to read more) General Fitment914 1970-76
$74.36
Make a selection K1295 If you are building a high performance 914 engine or have had an engine fire, carburetion is for you! Recommended only for 2.0l engines and big bore engines that are running at least 3/4 cam. Each kit contains two carburetors, cast aluminum manifolds, fuel line, clamps and all necessary gaskets. The special mounting hardware for the linkage arms is made from an aluminum alloy casting that is much stronger and more rigid than a thin metal stamping. The throttle arms ride in individually adjustable heim (ball) joints for easier adjustment and smoother throttle response. Kit comes complete with two new 44 idf carburetors, manifolds, linkage, chrome air cleaner, hardware kit and fully illustrated instructions. When...(choose a part on the right to read more) General Fitment914 1970-76
$1,269.00
Make a selection 022129637B 1.7 and 1973-74 2.0. this is necessary equipment for 73-74 1.7 & 2.0 fuel injected cars. it fits onto the plentium, on the passenger side, and connects to the vacuum line going to the oil filler pcv valve and also the decel valve small front fitting. View/Change Diagram
$26.33
Make a selection FSPOR992SC Purchase disclaimer: fabspeed motorsport does not condone the use of emission defeat devices for any vehicles used on public streets or roadways. Fabspeed motorsport will not tamper, remove, disable, or bypass emissions equipment on a motor vehicle in accordance with 40 cfr section 86.1854.12(a)(3), clean air act 40 cfr 1068.101(b). This includes software, known as tunes, that reprogram a motor vehicles electronic control module to alter engine performance and enable the removal of filters, catalysts, and other critical emissions controls.
$3,991.63
Make a selection GR089091 Cleans throttle bodies inside and outside without dismantling or disconnecting the fuel line. Does not contain methylene chloride, chlorinated solvents, chloroflourocarbons, lead, phosphorus or silicone. General FitmentACCESSORY
$10.66
Make a selection AAA133000 In the early 1970s the factory authorized a recall of all 914s for replacement of the cloth covered upper fuel lines with high pressure rubber covered ones impervious to battery acid. Now you too can duplicate the factory procedure with this high pressure kit including the pre-bent injector elbows and special nonintrusive clamps. General Fitment914 1970-76
$157.64
Make a selection GS246 Finally, a durable high-performance speaker that will fit the stock speaker housings of your 914. The gs series of speakers is a more aggressive and more comprehensive line with a size to fit almost any mobile audio application. The silver poly injection cones give the gs series the versatility to accurately reproduce sound while the butyl rubber surrounds allow them to stand up to a beating - over and over. General Fitment914 1970-76
$81.00
Make a selection 022133315B Beautiful refinished in yellow zinc plating fuel rail for the left drivers side with a tap for a fuel pressure gauge or the 2.0 cold start fuel injector line View/Change Diagram
$62.96
Make a selection 1002110212DA This is a high-quality replacement for original number, 911 211 021 14 manufactured by dansk. It is manufactured in stainless steel and includes the necessary brackets and tabs for a direct bolt on replacement. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911101 sold individually. 1 necessary per car. Please note: the corresponding right side i...(choose a part on the right to read more)
$1,764.18
Make a selection 170211021MEC This is a high-quality replacement for original number, 911 211 021 14 manufactured by dansk. It is manufactured in steel and includes a corrosion resistant protective coating. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911101 sold individually. 1 necessary per car. Please note: the corresponding right side is our part # 170211022
$1,443.42
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |