PORSCHE 356A BUSHINCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 924 1976-79 - Body (includes uncategorized and accessory items) FVD34391101SET Replace worn-out original front lower control arm bushings to return your car to its intended suspension geometry and steering feedback. Features: better handling reduces that sloppy steering feel does not produce any noise like the teflon bushings. Rubber has the original shore hardness value of 65 (like oem) fit's like oem, simple installation made in Germany if you are looking for a sportier upgrade we suggest our sport lower control arm set, part # FVD34391192set. Set is sold per axle. 2 necessary per car.
$152.90
Make a selection FVD33391100SET Replace worn-out original spring plate bushings to return your car to its intended ride quality and performance. This is a high-quality OEM 65 shore density bushing set, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection
$30.80
Make a selection
$48.18
Make a selection FVD33300902AT Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this only fits cars with the g50 transmission.
$261.80
Make a selection 477871763A Known as: threaded sleeve View/Change Diagram
$8.86
Make a selection FVD34791130 Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)
$222.24
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection 91110190160EQ Oem (original equipment manufacturer) complete set of bearings (including # 8) sourced in Germany to ensure quality, reliability and precise fitment. Set includes: 1 qty. Crankshaft main bushing sleeve - bushing viii - oversize +0.25mm 12 qty. Crankshaft main bearing shells ii-vii (half) - oversize +0.25mm 2 qty. Crankshaft main bearing shells i (half) - oversize +0.25mm sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$692.05
Make a selection FVD205993001HA H&r rear sway bar with a 24 mm diameter. 2-way adjustable. This is the rear sway bar from our kit, part # FVD205993001. Includes bushings. Sold individually. 1 needed per car.
$401.50
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection 911FDLNK Upgrade your stock front swaybar with this simple bolt in replacement for the factory drop links.
$205.00
Make a selection FVD34101702RAT We will send you a reconditioned control arm, kindly send back your old part, or core . The reconditioned control arm has been full inspected, disassembled, degreased and we have properly installed FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. This part is sold on an exchange basis, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and r...(choose a part on the right to read more)
$440.00
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection 99333104503ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install the bushings. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part.
$254.10
Make a selection 96434101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 99334101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install original control arm bushings. . Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part. Sold individually....(choose a part on the right to read more)
$418.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |