Vehicles
Sections
213 not categorized PORSCHE 930 BUSHINGSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 924 1976-79 (includes uncategorized and accessory items) 98711691325 Tech tip: renew the ims bearing when replacing/renewing the clutch or all 100,000 km.
$521.40
Make a selection FVD33300902AT Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this only fits cars with the g50 transmission.
$261.80
Make a selection FVD33391101SET These bushings are manufactured from higher density, rs specification rubber (85 shore). Rs bushings are more durable than OEM 65 shore, provide more positive suspension location and are still quiet and compliant for street use. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD33391100SET Replace worn-out original spring plate bushings to return your car to its intended ride quality and performance. This is a high-quality OEM 65 shore density bushing set, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD33394401SET Replace worn-out original spring plate bushings to return your car to its intended ride quality and performance. This is a high-quality OEM 65 shore density bushing set, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This set is a direct replacement for the rear axle strut bushings from original part # 477 511 201 and 477 511 202 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection NLA10202502 Made by scat replaces 61610202502
$66.00
Make a selection FVD37504332R Replace the worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushings. These are manufactured of rubber with an 85-shore hardness value. 85-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings. Rubber has a shore hardness value of 85 (like rs models) made in Germany sold as a set. 1 necessary per car.
$152.90
Make a selection
$315.87
Make a selection
$48.18
Make a selection
$30.80
Make a selection
$2.95
Make a selection
$307.70
Make a selection 477871763A Known as: threaded sleeve View/Change Diagram
$8.86
Make a selection 90162892301 This is the female of the two required bushings per wiper shaft. easily installed with the rack removed. View/Change Diagram
From $15.81
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection P904784 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All performance products torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment924 1976-79924 1980-85 924 1986-88 944 1982-85 944 1985-88 944 1989-91 968 1992-95
$347.95
Make a selection FVD34791130 Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)
$222.24
Make a selection 96434101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection P904785 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All performance products torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment924 1976-79924 1980-85 924 1986-88 944 1989-91 944 1985-88 944 1982-85 968 1992-95
$375.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |