Vehicles
Sections
407 not categorized PORSCHE 356 A SUSPENSIONCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 928 1978-82 (includes uncategorized and accessory items) FVD33391101SET These bushings are manufactured from higher density, rs specification rubber (85 shore). Rs bushings are more durable than OEM 65 shore, provide more positive suspension location and are still quiet and compliant for street use. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$154.00
Make a selection BES98115000S This is a forum favorite for the best sound with minimal drone! This muffler really does everything so well. Civilized while cruising, a beast under load and cup car gurgles and crackles off throttle. + 11 hp & + 10 tq gain. - weighs 35.4 lbs - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 1/2 tubing (63.5 mm). - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin (200 rpms worth) compared to the competition's mufflers. This can be verified on the forums like ...(choose a part on the right to read more)
$3,314.30
Make a selection BK7032 Originally published by floyd clymer this is a faithful reproduction of the 1969 publication of that manual. By far the most comprehensive manual ever published for the 912 Porsche it includes complete technical data, service and maintenance information and comprehensive detailed instructions for the repair and overhaul of all major and minor mechanical and electrical components, making it an invaluable resource for collectors and restorers of these classic automobiles. There are separate sections that deal with the repair and overhaul procedures for the engine, ignition system, fuel system, clutch, transmission, rear suspension, steering, front suspension, brakes, heater, exhaust and emission control system pl...(choose a part on the right to read more) General FitmentACCESSORY
$39.95
Make a selection BK7033 Re-issue of autobooks manual covering engine, fuel & cooling systems, ignition, heating, exhaust emissions, clutch, transmission, rear axle, suspension, steering gear, brakes, electronics, and bodywork. This is a manual that will help keep 912 on the road. A must for any 912 owner. General FitmentACCESSORY
$32.00
Make a selection FVD33150001 Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)
$243.10
Make a selection 115910987013 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber set (4 pieces) for your Porsche with standard suspension, pasm and manual transmission. The b4 dampers from bilstein are the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
$2,088.24
Make a selection BES98215000S2 The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$2,816.00
Make a selection BES981C5000SKGT Gt4 clubsport ++ with the valves open. Completely civilized at low rpms and while cruising. + 11 hp & + 10 tq gain. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - 2 3/4 tubing. - 2 x 3.5 (90 mm) round tips. - intoxicating growl at idle, partial throttle and wide open throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - minimal resonance / drone in the cabin. - "aero quip" style motorsport muffler connections to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. Please note: gaskets a...(choose a part on the right to read more)
$5,362.50
Make a selection 99333105280 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $764.50
Make a selection 99634304347 Serie production spring seat must be used! Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber for your Porsche with standard suspension. The b4 damper from bilstein is the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
From $431.07
Make a selection FVD34101702RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection BBI9964010001 Features
$525.00
Make a selection 99333105180 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $764.50
Make a selection 99633305151 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber for your Porsche with standard suspension. The b4 damper from bilstein is the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
$460.88
Make a selection 99633305153 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber for your Porsche with standard suspension. The b4 damper from bilstein is the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
$460.88
Make a selection 99633305146 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber for your Porsche with standard suspension. The b4 damper from bilstein is the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
$460.88
Make a selection 96434307001SP Replace your old drop links to reduce body roll and rejuvenate your cars handling in the corners. Sport-version with 85 shore 964 c2 only with m030 factory sport suspension sold individually. 1 necessary per car.
$238.70
Make a selection 90134722303R The original rubber bushing is proven to be a weak link that can fail prematurely, allowing chassis geometry to be compromised. Symptoms include suspension movement during acceleration, braking and cornering. The powerflex black series bushing is manufactured of a more dense rubber than the original. It is a 95 shore compound that is more resistant to load than standard rubber which provides better control of chassis geometry for track use. Features: designed for track use improved track handling more precise and accurate alignment constant steering geometry increased tire life better steering feedback longer service life of suspension components less nvh (noise vibration hardness) than polyurethane bushings pl...(choose a part on the right to read more)
$37.40
Make a selection 91134732204EQ The symptoms of a worn tie rod end include, clunking, rattling and squeaking when turning, poor alignment and premature tire wear. Have the rod ends inspected when servicing your suspension and proactively change them when noticing any of the symptoms. Quality European aftermarket replacement designed to perform like the original. Sold individually. Left or right-side fitment. 2 necessary per car.
$64.90
Make a selection 184584002X Containing absolutely everything a 911sc owner needs to know, every model and version is included. Engines, transmissions, suspension, and how to improve the performance are covered. This book really is the essential companion for the 911sc owner or would-be owner. 416 pages. General FitmentACCESSORY
$118.50
Make a selection 150SPB976 Replace worn-out spring plate bushings with these longer lasting poly-graphite plastic bushings. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This includes the inner and outer bushing for the 2-piece adjustable spring plate. Sold individually. 2 necessary per car.
$39.60
Make a selection 150PB10134 Replace worn-out original sway bar drop link bushings with this longer lasting poly-graphite plastic bushing set. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. The set includes 4 complete bushings and 4 sleeves (8mm inner diameter). Sold as a set. 1 necessary per car.
$73.70
Make a selection 150PB1027 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's 911 models from 1978-89 if fitted with an 18mm original rear sway bar.
$49.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |