PORSCHE 356A IMS KITCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 928 1983-86 - Pedal System/Levers (includes uncategorized and accessory items) 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 100555964CA This is a complete floor carpet kit for cabrio models. This set is a lightweight fine German velour that is trimmed in vinyl. Each is cut, sewn and trimmed to fit perfectly. Driver's side vinyl heel pad and side pads (like original) is also included. Made in Germany. Sold as a set. 1 necessary per car.
$1,544.40
Make a selection 911051 Porsche 911 ac compressor upgrade kit, 1984-89, lh drive model provides improved integrity with our kuehl barrier hose set, kuehl low- high pressure switch to help protect the system, a new denso factory compressor with clutch, new kuehl drier, complete o-ring kit, along with r134a charge port adapters. you can use either r12 or r134a with refrigerant with this complete kit. all barrier hoses match OEM configuration, have sae sae approved crimped fittings and each hose is labeled so you know where it goes.
$1,097.00
Make a selection 914911356GROMKIT This kit is for most of the rubber grommets in your car. made by the German manufacturer wurth, these substitute for the impossible to find factory original and aid in the reassembly of your car.
$52.47
Make a selection 100555111NB This is a rear carpet kit for a rs model or a rs tribute, without back seats. This set is a lightweight fine German velour that is trimmed in vinyl. Each is cut, sewn and trimmed to fit perfectly. We can also add special order script on the rear deck, just contact us and let us know what you have in mind. Made in Germany. Sold as a set. 1 necessary per car.
$716.10
Make a selection 100555100RS1ST This is a lightweight carpet kit for a rs model or a rs tribute, without back seats. This set is made from lightweight fine German perlon felt that is trimmed in fabric. We go to extra lengths to ensure that our carpets are made as closely to the originals as possible. Each is cut, sewn and trimmed to fit perfectly. Details: German lightweight perlon felt includes trim / edging made in Germany does not include floormats custom made to order sold as a set. 1 necessary per car. Please note: this set does not include floormats when placing your order, we require the year, model and a list of any interior upgrades like roll bars, etc. This kit is custom made to order.
$984.50
Make a selection F9164120104MES Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to ensure that you select a high-quality product like your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and include the original die cut notches for easy installation. Each kit varies, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. Don't see the color or combination that is right for your car? Or perhaps you want a custom logo in the tach? Kindly contact us f...(choose a part on the right to read more)
$858.00
Make a selection BBI9964010002 Finally, a complete solution to properly widen the front track width of a Porsche 996 and 997 turbo. To help increase front end grip, this kit allows full negative camber adjustment without binding the axles and fitment of wider wheel/tire combinations and GT3 cup car fenders. Each kit includes lower control arms, thrust arms, axle spacers, upper mounts, and camber shims.
$3,695.00
Make a selection FVD33396400 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,708.92
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection BBI9965010002 • provides additional rear toe adjustment
$875.00
Make a selection 99660610599 If you are noticing engine vibrations, misfires and even backfiring your crankshaft position sensor maybe bad. Your car's dme (ecu) uses the signal from the crankshaft position sensor to control ignition timing and fuel injection, so if your sensor is failing your engine is suffering from poor timing and is not running efficiently. This kit is complete and ready to install.
$132.77
Make a selection F6564120102 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high quality product similar to your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit is made for global distribution, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. This kit includes faces for: manual transmission / tiptronic transmission / kph / mph / celsi...(choose a part on the right to read more)
$603.90
Make a selection BBI9963010001 The bbi autosport Porsche 996/997 turbo clutch slave cylinder conversion kit is a direct replacement part that eliminates the problematic factory power-assist system for improved reliability and pedal feedback. The factory power-assisted clutch system has always been the achilles heel for the Porsche 997 turbo. Utilizing the power steering system to help reduce the force needed to depress the clutch pedal, it is a flawed design that delivers a mushy pedal feel with poor feedback, and is highly prone to failure.
$1,330.00
Make a selection BBI9964010001 Features
$525.00
Make a selection FVD33396500 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,730.94
Make a selection FVD1109114840 This replica high butterfly mfi throttle bodies system is for those looking for ultimate engine performance as well as an authentic rsr engine appearance. This kit keeps air consistently on tap for superior drivability. When the throttle is opened, there is an instant injection of air, providing a sharp, crisp throttle response. This efficient injection frees up more power and compliments larger displacements, high lift cams and full exhaust systems. This kit is engineered, precision machined, flow tested and manufactured in Germany. It is replicated to look as close to the original as possible. Intake trumpets (velocity stacks) are available in your choice of red or black. Includes: 6 individual stacks (48 mm ...(choose a part on the right to read more)
$7,456.90
Make a selection FVD123025ATK K24/26 exchange turbo (only OEM k24 exchange accepted) (up to 700 hp) power is focused on mid and top range rpm's. Facts: - modified compressor housing and backing plate - modified & lightened high flow compressor wheels. - remanufactured by kkk / borg warner certified technicians - free software update for those already running FVD software. FVD brombachers 996 k24/26 race turbos are new units created for those who are looking for ultimate in performance. Power is focused in the mid and top rpm range while keeping turbo lag low. They are completely bolt on and do not require custom headers or special modifications. The factory OEM turbocharger compressor housing is re-profiled and the compressor backing plate...(choose a part on the right to read more)
$2,976.60
Make a selection FVD123014ATK K-16/24 turbo (up to 555hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbocharg...(choose a part on the right to read more)
$2,976.60
Make a selection FVD12399600R Silicone boost hose kit FVD's direct replacement boost hose kit eliminates common boost hose "blow outs" on modified turbo's. Facts: tested to withstand over 75 psi (5 bar) boost pressure.fuel and oil resistanttemperature range between - 50 to + 180 degreesbolt on kit over time the OEM boost hoses tend to expand and contract under higher load, which leads to leaks, or "blow outs". Also, the OEM aluminum end does not secure properly into the intercooler, which causes boost leaks, and boost hose blowouts. Our machined billet ends are a perfect secure fit and our silicone hose is designed not to expand under boost pressure. The hose kit is a complete bolt on kit.
$590.70
Make a selection FVD1109115043 This replica high butterfly mfi throttle bodies system is for those looking for ultimate engine performance as well as an authentic rsr engine appearance. This kit keeps air consistently on tap for superior drivability. When the throttle is opened, there is an instant injection of air, providing a sharp, crisp throttle response. This efficient injection frees up more power and compliments larger displacements, high lift cams and full exhaust systems. This kit is engineered, precision machined, flow tested and manufactured in Germany. It is replicated to look as close to the original as possible. Intake trumpets (velocity stacks) are available in your choice of red or black. Includes: 6 individual stacks (50 mm ...(choose a part on the right to read more)
$7,456.90
Make a selection FVD347088CS The momo prototipo 6c is a classic wheel with a modern carbon twist, it uses the finest modern materials giving it the perfect blend of old and new. Made from top grain black leather that includes contrasting grey stitching to match the wrapped carbon cut-out spokes. The wheel also includes a momo horn button. The momo prototipo 6c is the excellent choice for those wishing to retain the character of their vehicle while refreshing the interior. Style: rally color: black material: leather spoke finish: wrapped polished carbon / cut out horn: matte black with gloss momo horn button diameter: 13.78 in (350 mm) rim diameter: 1.29 in (33 mm) dish: 1.4 inch (37 mm) weight: 2.86 lbs. (1.3 kg) please note: this kit is o...(choose a part on the right to read more)
$739.20
Make a selection FVD33399300 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of TUV certified eibach springs. This suspension kit will lower the front axle to a maximum of 35 mm (1.37 inches) and the rear axle to 30 mm (1.18 inches), like the European rennsport model. The height is adjustable as the dampers are threaded. They are a cost effective solution for clubsport use and will be well mannered on the street. Sold as a complete kit. 1 kit is necessary per car.
$11,872.30
Make a selection FVD123013 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection F91641202TU04S Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to make ensure that you select a high-quality product like your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and includes the original die cut notches for easy installation. Each kit varies, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. Don't see the color or combination that is right for your car? Or perhaps you want a custom logo in the tach? Kindly contac...(choose a part on the right to read more)
$1,021.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |