Vehicles
Sections
349 not categorized PORSCHE 924 DEL SOLCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 928 1983-86 (includes uncategorized and accessory items) 9A112601105 A failing a/c compressor elevates cabin temperatures, emits loud sounds as the bearing fails and the internal clutch can even seize. If you experience any of these signs, replace your a/c compressor with this quality denso OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: this is meant for r134a refrigerant. Please check the model fitment tab to ensure accurate fitment.
From $1,042.80
Make a selection 99919233850EQ Belts undergo a lot of friction and wear. They are cost effective to change and will keep your alternator and engine in good condition. Be sure to follow recommended service and replacement intervals set by Porsche on belts. Please note: specific model fitment information below. Sold individually. 1 necessary per car.
$14.30
Make a selection 9A110221200 High-quality ina OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This part includes the protection cap, bearing and roller housing. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
From $19.25
Make a selection 9A160410300EQ If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually, you will hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter, be sure to check the protection cap on the terminal for cracks which allows moisture in and causes pre-mature failure. High-quality denso OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$485.10
Make a selection 964541225001 This genuine Porsche windshield seal is an integral part of keeping your cowl from rusting. It is critical that the gasket and windshield are properly installed to prevent corrosion. Sold individually. 1 needed per car. Please note: for the 911 models, this does not contain the trim frame slot for chrome / black trim like the earlier cars.
$406.00
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,544.10
Make a selection F8764121000294C Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to ensure that you select a high-quality product like your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night-time shading and include the original die cut notches for easy installation. Each set varies, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match interior or exterior color schemes. Don't see the color or combination that is right for your car? Or perhaps you want a custom logo in the tach? Kindly ...(choose a part on the right to read more)
$658.90
Make a selection BES98215000SK Brombacher edition valved mufflers are the perfect compromise for you and your loved ones. Rich, deep race car tones with the exhaust valve open and soft subtle, nearly stock sounds with it closed. + 17 hp & + 13 tq gain. - 2 x 3.5 (90 mm) round tips. - includes a pierburg vacuum actuated exhaust valve. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - intoxicating growl at idle, partial throttle and wide open throttle with the valves open. Factory quiet with them closed! - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport muffler connections to ensure a leak free exhau...(choose a part on the right to read more)
$5,309.70
Make a selection BES99125020SK No need for Porsche sport exhaust (pse) envy with this muffler! This offers weight savings and a far more exotic sound than the pse, all without drone. It is the perfect compromise for you and your loved ones. Rich, deep, turbo motorsport tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english and is the best choice for a daily driver. Features: - + 16 crank hp & + 15 crank torque. - weighs 37 lbs. (17 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - direct bolt on replacement for the factory center muffler. - includes necessary installation hardware. - reduces turbo lag, backpressure and thermal lo...(choose a part on the right to read more)
$4,651.90
Make a selection F8764121004PDK Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to ensure that you select a high-quality product like your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night-time shading and include the original die cut notches for easy installation. Each set varies, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match interior or exterior color schemes. Don't see the color or combination that is right for your car? Or perhaps you want a custom logo in the tach? Kindly ...(choose a part on the right to read more)
$603.90
Make a selection F8764121007MTIP Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to ensure that you select a high-quality product like your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night-time shading and include the original die cut notches for easy installation. Each set varies, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match interior or exterior color schemes. Don't see the color or combination that is right for your car? Or perhaps you want a custom logo in the tach? Kindly ...(choose a part on the right to read more)
$603.90
Make a selection FVD361900815EU This fuchs replica is a classic design perfectly suited for any Porsche model. The center section is cast aluminum and finished black with a layer of clear coat. TUV approval documentation is standard with each wheel. The wheel accepts factory Porsche wheel bolts and center caps. Center caps sold separately, part # 190361035 or 190361033 sold individually.
$476.30
Make a selection FVD105911930 This kit contains everything needed for a valve adjustment. High-quality victor reinz gaskets with hardware, designed to perform like the original. We source this kit in Germany to ensure quality, reliability and precise fitment. Set includes: 2 qty. Lower valve cover gaskets 93010519507 2 qty. Upper valve cover gaskets 93010519404 2 qty. Oil strainer / sump plate gaskets 93010139101 2 qty. Sealing rings 90012311830 8 qty. M6 nuts 8 qty. Chain case washers 34 qty. Valve cover nuts 34 qty. Valve cover washers sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$71.18
Make a selection FVD11401214 Hailing from the baden wurttemberg region in Germany, speaking the language and dealing with lead engineers from the OEM and motor sport manufacturers for more than 30+ years has many advantages. We are able to source this flywheel from an elite German motorsports manufacturer who delivers the highest quality available. Features: quicker acceleration 9 bolt scalloped design precision machined billet steel computer balanced made in Germany replacement for original number 93010220201 sold individually. 1 necessary per car. Please note: this only fits 930 turbo models from 1978-79.
$526.90
Make a selection FVD11GK181GF Motorsport quality grp (glass-reinforced plastic) front bumper bar. Features: - produced by an German motorsport manufacturer. - lightweight 5.7 lbs. (2.6 kg) - made of high strength, grp (glass-reinforced plastic) sold individually. 1 necessary per car. Please note: please provide us with the year / model. These are motorsport quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. All grp products must properly be fitted and completely prepared prior to paint.
$559.90
Make a selection FVD201911964993 Looking to update your fuel cap? This is a cost effective, sporty, aluminum alternative to the factory cap. It resembles the tequipment cap available on the water-cooled models. It is a quality tuning product manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Oem non-locking, screw type fuel cap sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary ...(choose a part on the right to read more) General FitmentACCESSORY
$136.40
Make a selection FVD33150046R Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$66.00
Make a selection FVD20799601 Scavenging and aeration in the oil pan have been identified as a problem in 996 and Boxster models experiencing high g-forces on the racetrack. This oil pan spacer provides a simple solution. This spacer increases sump capacity by half a liter, providing more reserve to ward off starvation. Thisoil pan spacer clears all factory options including the rear skid plate. Added oil capacities as well as increased oil pan surface area increase oil cooling and engine performance. *oil pan and sump baffle are OEM parts and do not need to be purchased material: 6061 t6 aluminum alloy finish: clear anodized weight: n/a models: Boxster, Boxster s, and 996 models (excludes GT3 and turbocharged models) installation: for best...(choose a part on the right to read more)
$283.80
Make a selection BBI9974010001 Features
$1,895.00
Make a selection FVD331993001 Our new rear sub frames contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. FVD clubsport sub frame facts: - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. - new sub frames with inserts installed. Sold as a set. 1 kit is necessary per car.
$1,758.90
Make a selection FVD33399300 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of TUV certified eibach springs. This suspension kit will lower the front axle to a maximum of 35 mm (1.37 inches) and the rear axle to 30 mm (1.18 inches), like the European rennsport model. The height is adjustable as the dampers are threaded. They are a cost effective solution for clubsport use and will be well mannered on the street. Sold as a complete kit. 1 kit is necessary per car.
$11,872.30
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD34307201 Our direct replacement, OEM quality link uses rubber with a shore hardness value of 85. That is the same value as the rennsport models from Porsche. This link will offer superior performance under high cornering loads, more durability and are still forgiving for street use. Road noise not compromised with our links either. Facts: made in Germany. Crafted from high carbon steel and 7075 t6 aircraft aluminum. Weather sealed. Sold individually. Please note: we recommend buying these as a set, please purchase the left link, our part # FVD34307101
$93.50
Make a selection FVD361900715EU This fuchs replica is a classic design perfectly suited for any Porsche model. The center section is cast aluminum and finished black with a layer of clear coat. TUV approval documentation is standard with each wheel. The wheel accepts factory Porsche wheel bolts and center caps. Center caps sold separately, part # 190361035 or 190361033 sold individually.
$410.30
Make a selection FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$154.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |