Vehicles
Sections
113 not categorized PORSCHE 911 REAR SUSPENSIONCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 928 1983-86 (includes uncategorized and accessory items) 115900997TTCS The ultimate bilstein sport suspension for club racing and street performance! This suspension was developed under real racing conditions by bilstein with double world rally champion walter rohrl. - reduced weight via the use of an integrated reservoir. - 2 way damping adjustment (bound (red) and rebound (blue) independently). - dials with good visibility and scaling (from 1 to 10). - easy to adjust when installed with click screening and color coding. - bilstein mono-tube gas pressure technology. - adjustable aluminum uniball camber plates (rear). - TUV approved. - made in Germany. What's in the box: - adjustable dampers including double springs. - rear uniball camber plates. - spring tensioning key (tool). -...(choose a part on the right to read more)
$7,256.70
Make a selection 115900997BI Now you can enjoy the kind of precise suspension tuning formerly available only on race cars. The pss 9 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings, from comfort to competition. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. *** these pss9's are for models without Porsche active suspension management***
$3,914.90
Make a selection 115900997BIT011 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 150PB1027 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's 911 models from 1978-89 if fitted with an 18mm original rear sway bar.
$49.50
Make a selection 150PB100918 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 150PB100922 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 115900997BIT021 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 92833305116 Sach/boge suspension components have been standard equipment on Porsche for years. Buy with the knowledge that the factory uses sachs/boge parts and stands behind their quality and precision that they bring to everything the manufacture. Sachs/boge shocks and struts provide a taut, sporty ride while remaining a comfortable street ride. Sold each, two needed for the rear of your vehicle. View/Change Diagram
From $153.50
Make a selection BK7032 Originally published by floyd clymer this is a faithful reproduction of the 1969 publication of that manual. By far the most comprehensive manual ever published for the 912 Porsche it includes complete technical data, service and maintenance information and comprehensive detailed instructions for the repair and overhaul of all major and minor mechanical and electrical components, making it an invaluable resource for collectors and restorers of these classic automobiles. There are separate sections that deal with the repair and overhaul procedures for the engine, ignition system, fuel system, clutch, transmission, rear suspension, steering, front suspension, brakes, heater, exhaust and emission control system pl...(choose a part on the right to read more) General FitmentACCESSORY
$39.95
Make a selection BBI9965010002 • provides additional rear toe adjustment
$875.00
Make a selection FVD33150001 Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)
$243.10
Make a selection FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$154.00
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$451.96
Make a selection 92833305112 Bilsteins are original equipment on many Porsches and have won, for Porsche, countless races. Bilsteins are the highest quality shocks made and will last the lifetime of your Porsche. Bilstein sport shocks and struts are for the performance minded driver. Bilstein sport units deliver absolute mastery of the road surface. Designed to push a car's suspension to its performance peak, these super-firm units are well suited for use with special springs, anti-sway bars, and other suspension upgrades. As with other bilstein units, sports are uniquely self-adjusting. Sold each, two needed for the rear of your vehicle. View/Change Diagram
$273.96
Make a selection FVD33399600B6 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$2,442.00
Make a selection FVD33399600B8 Bilstein suspension featuring with upside/down technology. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$2,310.00
Make a selection FVD721T221 Camber adjuster needed to adjust toe - in of the rear suspension.
$15.40
Make a selection FVD33399602B8 Bilstein suspension featuring eibach springs. Lowering 35 mm front and 30 mm rear - giving it a GT3 stance
$1,944.80
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection 99335193901S Mintex silver brake pads contain a special metallic brake compound provides exceptionally long life, reduced brake rotor wear, and excellent heat dissipation for maximum performance under all driving conditions. This unique mintex silver composition provides unmatched brake "feel" while it eliminates annoying squeals and dusting. General Fitment911 1989-94928 1983-86 928 1987-91 944 1989-91 968 1992-95 928 1992-95 911 1978-83 911 1984-86 911 1987-89
$41.99
Make a selection 115910996032 Bilstein b4 OEM m030 (original m030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory m030 sport suspension. Nothing is better than the original! The b4 m030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model m030
$1,682.59
Make a selection FVD34391192SET Replace worn-out original front lower control arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Features: better handling reduces that sloppy steering feel makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 2 necessary per car.
$158.40
Make a selection 115910996034 Bilstein b4 OEM m030 (original m030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory m030 sport suspension. Nothing is better than the original! The b4 m030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model m030
$1,784.11
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |