Vehicles
Sections
54 not categorized PORSCHE 924 FRONT MOUNTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 930 1975-77 (includes uncategorized and accessory items) 91160820600 Fuel pump mount (rubber mount with 6mm thread holes for front pump support bracket). 2 per car. View/Change Diagram
From $7.00
Make a selection 91153163100 This is the smaller base gasket for the door handle. When replacing this gasket, we recommend replacing the exterior large door handle gasket, part # 91153163200 and the securing nuts, part # 900 910 008 02 and washers, part # 900 025 003 02. Sold individually. Driver or passenger side fitment. View/Change Diagram
From $5.50
Make a selection 91150195500GRV Front floor with suspension mounts. Galvanized primed painted. One of the most abused part of the 911 are the floor panels. Years of exposure to moisture, salt, sand, and mud often takes a toll on the metal under your feel. If your Porsche floors have seen better days and are showing the ugly signs of corrosion, we have replacement panels. Each one is painstakingly made to duplicate the factory pieces and galvanized for long life. View/Change Diagram
From $598.40
Make a selection 115900944020CS Double spring suspension (racing) for 924 only for 20mm spring strut mounting this sport suspension was tuned and tested for racing use only (hockenheimring.net). Perfect handling, recommended for race and clubsport. Not for street use (racing suspension). The lowering is adjustable (30-70mm front and 30-60mm rear). By using springs at the rear axle instead of torsion bars you improve extreme the handling of your car. By removing the rear torsion bars is the weight saving approximately 25kg.
$2,633.40
Make a selection FVD20703500 This oil cooler kit is a must for engines that are modified. It reduces oil temperature and protects the engine. This kit can lower operating oil temperature up to 60* f. Simple installation without cutting or modifying. High quality behr cooler ensures reliability without sacrificing a/c performance as kit is mounted clear of the front a/c condenser. Can be mounted on cars with or without air conditioning. Sold as a complete kit, ready for installation.
$2,981.74
Make a selection FVD50599701MM For all Porsche 997 Carrera models with the standart front bumper! The mounting is very easy. With some screwing points under the Porsche front bumper. Not for models with the aerokit or turbo | GT2 | GT3 front bumper
$1,042.80
Make a selection FVD50399101MM The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)
$3,631.10
Make a selection FVD50599721MM For all Porsche 997 Carrera models with the standart front bumper! The mounting is very easy. With some screwing points under the Porsche front bumper. Not for models with the aerokit or turbo | GT2 | GT3 front bumper
$865.70
Make a selection FVD20798700 This FVD motorsports oil pump kit is a must for 987.1 Caymans and Boxsters driven on the track. Our kit includes a second return oil pump and our FVD motorsports oil pan. The issue: the 987.1 Boxster/Cayman from 2005 to 2008 has the factory return oil pump located on the right rear side. On the left side, the return oil pump located in front. So when driven fast in right turns, the oil from the camshaft case (rear left) does not flow back quickly enough into the oil pan. When the oil pan is starved of oil, the oil pump sucks in air and over time the motor will seize. The solution: our tandem return oil pump draws oil from the camshaft housing in (rear left, 3rd cylinder) and feeds it back into the oil pan so th...(choose a part on the right to read more)
$3,274.30
Make a selection SB809193 This system mounts like no other brace on the market. The dual bar design adds to the strength and resistance to deflection of the front suspension. The billet aluminum mounting brackets have been formed to perfectly fit the contour of your 911's strut towers, making installation a breeze. These truss style brackets have been engineered in a way that makes this brace not only one of the lightest, but one of the strongest braces on the market today. There is absolutely no alignment alterations or drilling required for installation. Fits all 911/912/930's from 1966-89. Silver in color. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$250.95
Make a selection SB809192B Most other 3 point braces require you to drill and attach the third leg into the flimsy cross member behind the gas tank. Rennline has manufactured a bracket that utilizes the same mounting studs used to attach the master cylinder bracket . This mounting area is one of the strongest points on the front of your 911, giving you the optimum rigidity needed to eliminate camber change in hard cornering. Both the upper and lower bars are fully adjustable allowing you to set the desired amount of pre-stress. Constructed entirely out of aircraft grade aluminum. Fits all 911/912/930's from 1966-89. Black in color, silver shown. General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 911 1965-69 912 1965-69
$265.95
Make a selection CB43201B Corbeau 2 inch double release harness belts are unique in that they have a disconnect feature between the front shoulder straps and the rear tail strap. This feature allows for easy access to the rear seat as you can disconnect that rear strap without taking the belts out. They also have the rare ability to be bolted to all your factory provided mounting points. What that means is all our hardware was manufactured to bolt right up to your factory bolt holes. In most cases no drilling or modifications are necessary, they just bolt right in. Corbeau 2-inch double release harness belts are available in a 3 point style with bolt-in mounting. General FitmentALL
$169.00
Make a selection FVDBRO1016003A Weight savings approximately 4kg (8.8 lbs) of rotating unsprung weight. Oem disk weight 10,8kg (23.8 lbs), brembo disk weight 8.9kg (19.69 lbs) rotors: (13") 330x34mm drilled discs bells / hats: precision milled billet aluminum hardware: brembo floating anti-rattle disc hardware by using an aluminum bell for the hub section of the disc, these rotor assemblies save a great deal of weight. Since this is both rotating and unsprung, it benefits the acceleration, braking, and handling of the vehicle. Secondly, it is better able to handle the large temperature changes that a brake disc experiences. The mounting system is designed to allow a specific amount of float in both radial and axial directions. Brembo has eng...(choose a part on the right to read more)
$1,815.00
Make a selection AFC11956 A necessary addition for any 911! This kit includes the components to install a mocal 19 row, 235 matrix (11"h x 6"w x 2"d) oil cooler in a factory "hard line" equipped car. This kit is especially good for replacing the factory "loop" oil device located in the front right fender, making it easy to upgrade to a mocal oil radiator at an economical price. Includes the cooler, two 90 degree 3/4 fitings, two 30mm straight fittings, and a 3/4 oil hose. This is our basic oil cooler kit. Note: for car that already have a factory oil cooler. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$423.50
Make a selection 914385 Brembo® GT brake systems were designed with one goal in mind, to maximize braking performance. These performance upgrades are a cost effective solution for those drivers who want to spend weekdays on the road and weekends at the track. Each kit comes complete with 4-piston brembo monobloc calipers with sequentially sized pistons, high performance ferodo brake pads, 323 x 28 mm (12.7“) one piece cross drilled brembo rotor, goodridge stainless steel braided lines, billet aluminum mounting brackets, and factory spec hardware. Requires 17” or larger wheels. Calipers are available in red, black, silver, or yellow; please indicate your color choice when ordering. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$2,299.00
Make a selection FVD35198001 Brembo direct replacement 2-piece rotors for the '04-'06 Porsche Carrera GT designed to be used with the vehicles OEM brake calipers. These include brembo's high thermal type iii rotors , billet aluminum bells, and anti-rattle floating hardware. The floating disc mounting system is designed to allow a specific amount of float in both radial and axial directions. Brembo has engineered special springs that are used on every other fastener in order to slightly preload the assembly.
$2,832.54
Make a selection 60380C This cage kit welded to an autopower roll bar makes a race legal 6 mounting point roll cage. Autopower will choose tubing size when you place your order. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$584.37
Make a selection 60340C This cage kit welded to an autopower roll bar makes a race legal 6 mounting point roll cage. Autopower will choose tubing size when you place your order. General Fitment911 1974-77930 1975-77 911 1978-83 911 1984-86 911 1987-89
$584.37
Make a selection FVD3511M39040A2 The brembo gran turismo (gt) braking system with type iii rotors is ideal for ideal for clubsport and sprint type track events. It utilizes brembo type iii aggressive face-type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with opposed pistons, a complete set of high-performance brake pads, abrasion and corrosion resistant goodridge braided steel brake lines and high-quality fastener hardware...(choose a part on the right to read more)
$5,054.50
Make a selection FVDBSK351997201 Brake-service-kit: pads,sensors brake discs no anti-squel shims mounted on this car.
$455.40
Make a selection FVD3511M19004A The brembo gran turismo (gt) braking system is ideal for use on the street and for light track use. This GT system expands upon the original drilled disc's face type made by Porsche. The cross drilled disc surface continuously refreshes the braking surface and offers the highest initial response of any disc type. So, you can confidently respond to sudden pedestrian or traffic movement with maximum braking performance. Drilled discs operate in a wide range of operating temperatures and environments and respond confidently in wet weather. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with op...(choose a part on the right to read more)
$5,054.50
Make a selection EL2030900 Triangulation bests the single bar braces by increasing rigidity. traditional braces tie strut towers together force them to move in parallel, sharing the cornering force of the loaded tire over both towers to reduce flex. Triangulation locks the towers rigidly in place to maintain camber settings – even through high g corners. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$240.90
Make a selection NLA80390105100 Comes complete with mounting hardware 2 req'd
$71.50
Make a selection KEV503031011 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon fender that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 5.9 lbs. (2.68 kg) - made of high strength kevlar and carbon. - mounting is just like factory, no modifications are necessary. Please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world.
$1,215.50
Make a selection AA914505083B Long needed item consists of all of the special bolts washers and lock washers necessary to mount the 70-74 front or rear 914 bumpers. please order two kits to mount both front and rear and do not forget our special valance, spoiler and rocker panel mounting kits as well as our 650 piece body hardware kit! Rybber "dog bones" available separately
$19.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |