Vehicles
Sections
176 not categorized PORSCHE 930 PROPSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 930 1975-77 (includes uncategorized and accessory items) STP240 This dial gauge holder is needed to properly measure crank shaft flywheel and pulley end-play. Can also be universally to check clearances and run-out. Applicable: most every Porsche and vw air-cooled engine. Please call our office for availability. General Fitment356 1950-59912 1965-69 914 1970-76 911 1965-69 911 1994-98 911 1989-94 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$125.55
Make a selection 1002110212DA This is a high-quality replacement for original number, 911 211 021 14 manufactured by dansk. It is manufactured in stainless steel and includes the necessary brackets and tabs for a direct bolt on replacement. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911101 sold individually. 1 necessary per car. Please note: the corresponding right side i...(choose a part on the right to read more)
$1,603.80
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 1002110221DA This is a high-quality replacement for original number, 911 211 022 10 manufactured by dansk. It is manufactured in stainless steel and includes the necessary brackets and tabs for a direct bolt on replacement. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911100 sold individually. 1 necessary per car.
$1,329.90
Make a selection 10050305503GFK Made in europe by one of the manufacturers to Porsche. Extremely high-quality grp (glass-reinforced plastic) rear bumper that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 9.7 lbs. (4.4 kg) - made of high strength, grp (glass-reinforced plastic) sold individually. 1 necessary per car. Please note: this only fits in conjunction with widebody / rsr rear fenders, part # FVD503930001 . Please provide us with the year / model. These are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. All grp products must proper...(choose a part on the right to read more)
$1,265.00
Make a selection 1150002LI These are made with club sport events in mind. They work with stiffer springs and lowering springs (we recommend h&r or eibach) and have a fully threaded body for individual lowering like the original 993 cup suspension. Lowering is adjustable to 35 mm (1.37 inches) sold individually. For matching club sport shocks, please order part # 1150002re for the right and 2 qty. Part # 1150009 for the rear. For a properly spec'd complete kit including front and rear club sport shocks with lowering springs and rear drop links, please order part # FVD33399300.
$517.00
Make a selection 99918200336 If you are planning to install new wheels new lug nuts are the finishing detail that is necessary. This lug nut is quality made in Germany and is the perfect replacement for your worn originals. Head length: 19 mm overall length: 32 mm material: lightweight aluminum alloy includes proper Porsche wheel nut rounded shoulder / ball seat made in Germany. Sold individually. View/Change Diagram
From $8.75
Make a selection 170211014 This steel heat control box is a quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 91121129700 clamp, part # 90121105222 and connecting piece, part # 91165911900 sold individually. 1 necessary per car.
$140.80
Make a selection 170211015 This stainless-steel heat control box is a quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 91121129700 clamp, part # 90121105122 and connecting piece, part # 91165911900ssi sold individually. 1 necessary per car.
$177.10
Make a selection 1150009 These are made with club sport events in mind. They work with stiffer springs and lowering springs (we recommend h&r or eibach) and have a fully threaded body for individual lowering like the original 993 cup suspension. You will need to run our drop links for the sway bar, part # FVD333900. Lowering is adjustable to 30 mm (1.18 inches) left or right side fitment. Sold individually. For matching front club sport shocks, please order part # 1150002li for the left and part # 1150002re for the right. For a properly spec'd complete kit including front and rear club sport shocks with lowering springs and rear drop links, please order part # FVD33399300.
$382.80
Make a selection 17021102103 This is a high-quality replacement heat exchanger manufactured by dansk. It is manufactured in steel and includes a corrosion resistant protective coating. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk930100 sold individually. Right or left side fitment. 2 necessary per car.
$837.10
Make a selection 240981351RSL1 Pagid yellow rsl1 are from the rsl line of endurance racing brake pads. They are a high friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl1 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and have good friction stability vs. Temperature. Applications include: GT cars, touring cars, prototype racing and in spring racing. Features at a glance: high friction coefficient high bite high fade resistance high pad and disc life high modulation pagid is one of the leading manufacturers of racing brake pads and is successful at the world's most demanding racetracks. They offe...(choose a part on the right to read more)
$734.80
Make a selection 17021101401 This steel heat control box is a quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 91121129700 and clamp, part # 99951234902 sold individually. 1 necessary per car.
$156.20
Make a selection 170211033SS This is a high-quality replacement heat exchanger manufactured by dansk. It is manufactured in stainless steel. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk930100 sold individually. Right or left side fitment. 2 necessary per car.
$1,144.00
Make a selection 99919217350EQ A severely worn a/c belt will no longer be able to grip the pulleys and will start to slip and cause a loud squealing noise when the a/c is turned on. Belts undergo a lot of friction and wear. They are cost effective to change and will keep you're a/c functioning properly. Be sure to follow recommended service and replacement intervals set by Porsche on belts. High-quality OEM Bosch replacement belt, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$18.70
Make a selection FVD721T223 Synchro removal tool kit needed for the proper removal of synchro rings from the gear. For Porsche 930 turbo's w/4speed 76-88 3rd, 4th gears.
$223.30
Make a selection 17092102S This cross over connector replaces original part # 930 111 157 01, it is a quality stainless steel replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 93011119307 and sealing ring, part # 91111118903 sold individually. 1 necessary per car.
$82.50
Make a selection 27021102901 This is a high-quality replacement for original number, 930 211 029 01 manufactured by dansk. It is manufactured in stainless steel. It is a replacement part dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911103 sold individually. Right or left side fitment. 2 necessary per car.
$1,417.90
Make a selection 240991352GRST1 Pagid red rst 1 are from the rst line of circuit racing / sprint racing brake pads. They are a high friction coefficient compound with high initial bite. Rst 1 pads have high temperature resistance, a progressive torque curve and are very fade resistant. They are a semi metallic resin bonded material containing steel and acrylic fibers. Rst 1 pads offer medium pad life and relatively high disc life with moderate modulation. They are suitable for heavy cars where high torque is necessary. Applications include: rally tarmac, GT cars, touring cars, nascar and high downforce formula cars. Features at a glance: very high friction coefficient high initial bite progressive torque curve very fade resistant medium modul...(choose a part on the right to read more)
$680.90
Make a selection
$33.00
Make a selection 240991351GS Pagid yellow rsl 29 are from the rsl line of endurance racing brake pads. They are a medium friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl 29 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and offer excellent release characteristics. Rsl29 pads offer low heat conductivity and work well with abs systems. They offer excellent modulation and controllability. They offer lower disc wear rates and are fade resistant up to a temperature of 650*c (1,202*f). Applications include: club racing, track days, touring cars, prototype endurance racing and GT cars. Features at a...(choose a part on the right to read more)
$708.40
Make a selection 240991352GS Pagid yellow rsl 29 are from the rsl line of endurance racing brake pads. They are a medium friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl 29 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and offer excellent release characteristics. Rsl29 pads offer low heat conductivity and work well with abs systems. They offer excellent modulation and controllability. They offer lower disc wear rates and are fade resistant up to a temperature of 650*c (1,202*f). Applications include: club racing, track days, touring cars, prototype endurance racing and GT cars. Features at a...(choose a part on the right to read more)
$654.50
Make a selection 96434101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection 91150301605KEV Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar headlight bucket. Features: - produced by an OEM manufacturer. - lightweight .6 lbs. (.3 kg) - made of high strength kevlar. - metal mounting ring is cast inside the bucket for mounting. Sold individually. 1 necessary per car. Please note: requires drilling for wiring, etc. This is a high-quality part that takes time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world.
$774.40
Make a selection 91150514704EQ This impact strip suffers from uv rays and wax residue, it detracts from your cars appearance and should be changed when servicing the front bumper. Be sure to add a clamping plate for proper installation, part # 91150514902 any of our OEM replacement parts are designed to appear and perform like the originals. We source these parts in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$165.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |