Vehicles
Sections
139 not categorized PORSCHE 944 TURBO ORDS OCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 930 1975-77 (includes uncategorized and accessory items) FVD351997GT2CS2 This kit convert's the 997 turbo GT2's / 997gt3 rs pccb rotors to 997 GT3 cup car steel rotors with green cup car pads ( for cars with central lock only ) this system is complete with everything that you need to install. Do not ruin your expensive ceramic brake discs on the track. Get ready for racing with the original and much cheaper Porsche motorsport steel brake discs! What's in the box: 4 x 2-piece brake discs (380 x 34 mm - front / 350 x 28 mm - rear) 4 x wear sensors 8 x cup brake pads (racing green) 8 x screws for brake caliper 8 x damping plates technical tip: also order stainless steel brake lines (FVD b96 355 97) and racebrake fluid (012 145 ca).
$7,309.50
Make a selection FVD10397506 Carrillo is one of the most respected connecting rod manufacturers in competitive motor sports. Carrillo rods are constructed from their propriety alloy and forged to their custom specifications. The rods are then fully machined to guarantee the removal of all surface imperfections. After heat treatment, each connecting rod is magnaflux inspected and hardness checked, then machined to final size. Each set is balanced and then shot-peened to achieve the ultimate in strength and fatigue properties. General Fitment911 1970-73911 1974-77 930 1975-77
$2,434.30
Make a selection 930123002X This remanufactured turbo is a direct replacement for original part # 930 123 002 00. The remanufacturing is completed in Germany by kkk/borg warner certified technicians. This ensures reliability, superior performance and cost effectiveness. The remanufacturing process includes: complete disassembly. All parts are cleaned, inspected and measured for tolerances. Turbine wheels are replaced. Thrust bearings are replaced. All new seals are installed. Internals are reconditioned. Parts are balanced (static & dynamic) according to balancing protocol. For a complete installation we recommend adding a gasket, part # 93012319105 an intake sleeve, part # 93011015801 and be sure to have a few spare studs on hand, part #...(choose a part on the right to read more)
From $2,981.74
Make a selection 96450520180 Original rsr spoiler flaps fits all turbo or wide body's. For 964 (narrow body) please order 964 505 201 81.
$401.50
Make a selection 96434705804SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)
$196.90
Make a selection 93042340109 The clutch cable disengages the clutch in order to safely shift the transmission. A failing clutch cable can produce the same symptoms as a failing clutch, so we recommend replacing the cable / cables when installing a new clutch. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This part number supersedes part numbers 930 423 401 02 / 03 / 05. Sold individually. 1 necessary per car. Please note: this fits the 1978 930 3.3 l turbo model from chassis # 930 880 0192 on.
From $27.00
Make a selection 93034703101 Standard on 930/911 turbo, a good upgrade for regular 911 and 914 models. Beacuse they are longer than regular tie rods, they are stronger and have more adjustment, leading to a better-dialed in feel. View/Change Diagram
From $43.91
Make a selection 99310117054 This is the original stud used in the rennsport and turbo (m64.20 / 60) models. We recommend them for your next engine rebuild. Sold individually. 24 necessary per car.
From $53.90
Make a selection 99312301352ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, install new waste gates, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turboc...(choose a part on the right to read more)
$2,194.50
Make a selection 99911321840 High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car. Please note: this only fits the wide body / turbo look 911 with the m491 wide body option. Please check the model fitment tab to ensure accurate fitment. View/Change Diagram
From $28.60
Make a selection FPOR0120 B&b headers w/ heat exchangers 1 3/4 inch Porsche 930 turbo 75-89 General Fitment930 1975-77
$3,430.53
Make a selection 99919234350EQ Belts undergo a lot of friction and wear. They are cost effective to change and will keep your alternator and engine in good condition. Be sure to follow recommended service and replacement intervals set by Porsche on belts. For 964 c2 tip trans. / 993 tip trans. / 993 c2/ s manual trans. And the 993 turbo. Sold individually. 1 necessary per car.
$11.00
Make a selection 99312301452ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turbocharger. After receiving y...(choose a part on the right to read more)
$2,194.50
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,544.10
Make a selection BES98215000S The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$3,367.10
Make a selection BES98215000SK Brombacher edition valved mufflers are the perfect compromise for you and your loved ones. Rich, deep race car tones with the exhaust valve open and soft subtle, nearly stock sounds with it closed. + 17 hp & + 13 tq gain. - 2 x 3.5 (90 mm) round tips. - includes a pierburg vacuum actuated exhaust valve. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - intoxicating growl at idle, partial throttle and wide open throttle with the valves open. Factory quiet with them closed! - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport muffler connections to ensure a leak free exhau...(choose a part on the right to read more)
$5,309.70
Make a selection BES99125010SK Are you one of those that are looking for more sound from your Porsche sport exhaust (pse)? Perhaps it's not quite as aggressive as you would like, or your last Porsche just sounded so much better? Don't worry, we have you covered, and the beauty is, you don't have to touch the catalytic converters which is a big no, no with Porsche dealers. With the valves open you receive a far more exotic, rich, deep, turbo motorsport tone and with the valves closed, soft subtle, completely stock sounds. So, absolutely no compromise and you will be thinking, the car really should have left the factory like this! Features: - + 10 crank hp & + 8 crank torque. - weighs 29 lbs. (13 kg) - German v2a - x5crni18-10 - 1.4301 stai...(choose a part on the right to read more)
$4,312.00
Make a selection CARP30ET4LE Since the mid 80's cargraphic has been developing, testing and producing exhaust systems made from the highest grade premium stainless steel. Cargraphic is a specialist supplier for various car company's, high-end tuning and racing teams throughout the world and they thrive off their own development, testing and production departments. Cargraphic's main production line in the south-west of england is fully equipped with modern machinery along with a highly qualified workforce, who together work hand in hand with their German partners. They are committed solely to select materials of the highest standards for a sublime optical-finish and an unmistakeable sound. General Fitment930 1975-77
$2,220.08
Make a selection BES99715040S2 Quiet version with catalytic bypass and 4x80mm end tips these versions of FVD sport exhaust system is specifically made for increased performance vehicles. Designed for tolerable, pleasant and sonorous sound (especially for the turbo cabriolet). The elimination of the catalysts reduced drastically the back pressure and increases the performance and throttle response to the max! - stainless steel exhaust system - catalytic bypass - 4x80mm end tips - 2 3/4 tubing (70mm) straight through design for maximum power - weighs 39 lbs. (18,1 kg) - made in Germany - dme programming necessary (catalytic adaption) - stock tips will fit. Tech tip: order also repair / gasket set FVD mk9 970 02
$2,928.20
Make a selection FPOR0200 B&b exhaust muffler oval cut edge tip Porsche 930 turbo 75-89 General Fitment930 1975-77
$1,313.37
Make a selection CARP30ETTO Since the mid 80's cargraphic has been developing, testing and producing exhaust systems made from the highest grade premium stainless steel. Cargraphic is a specialist supplier for various car company's, high-end tuning and racing teams throughout the world and they thrive off their own development, testing and production departments. Cargraphic's main production line in the south-west of england is fully equipped with modern machinery along with a highly qualified workforce, who together work hand in hand with their German partners. They are committed solely to select materials of the highest standards for a sublime optical-finish and an unmistakeable sound. General Fitment930 1975-77
$1,477.58
Make a selection CARP30ET4 Since the mid 80's cargraphic has been developing, testing and producing exhaust systems made from the highest grade premium stainless steel. Cargraphic is a specialist supplier for various car company's, high-end tuning and racing teams throughout the world and they thrive off their own development, testing and production departments. Cargraphic's main production line in the south-west of england is fully equipped with modern machinery along with a highly qualified workforce, who together work hand in hand with their German partners. They are committed solely to select materials of the highest standards for a sublime optical-finish and an unmistakeable sound. General Fitment930 1975-77
$2,220.08
Make a selection FSPOR911TIC Product details: General Fitment911 1987-89911 1984-86 911 1978-83 930 1975-77
$2,395.00
Make a selection FPOR0216 B&b exhaust muffler right side exit w/ wastegate pipe Porsche 930 turbo 75-89 General Fitment930 1975-77
$1,640.68
Make a selection FVD721883081 High quality, German made brake bleeder and vacuum pump kit. Ideal for use on brakes, clutches, hvac, bleeding the fuel system or testing vacuum on a turbocharged system. Vacuum can be tested up to 0.9 bar and pressure up to 4 bar. The kit is complete with a variety of hose ends for various connections. Sold individually. General FitmentACCESSORY
From $246.40
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |