Vehicles
Sections
448 not categorized PORSCHE 924S CHECK OUTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 930 1975-77 (includes uncategorized and accessory items) 911561051012EQ This is the top outer section of the cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers are made for modern electric tops with stronger frames for the 911 and 964. Sonnenland high quality material was originally used by Porsche and other top German manufacturers. Made in Germany. This would replace original part # 911 561 051 012xw sold individually. 1 necessary per car. Only f...(choose a part on the right to read more)
$1,141.80
Make a selection 91156419100 This is the felt or velvet sealing strip that protects the outer edge of the sunroof panel. It assists in keeping out moisture and protects the panel during operation. It can become brittle and will crack overtime so it is essential that it is in good order. It can also lose the plush black appearance with wax applications. Sold individually. 1 needed per car. View/Change Diagram
From $44.00
Make a selection 91157132032 For proper installation we recommend replacing the sealing ring, part # 49025001 and the fastening clamp, part # 90157191900 high-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. If your fan is in good working order, we also sell the blower motor without the fan, part # 911571320322 sold individually. 1 necessary per car. View/Change Diagram
From $105.00
Make a selection 91163111502 This is the seal that sits between the adjustment ring and the outer headlight trim ring. Sold individually. Driver's and passenger's side fitment. 2 necessary per car. View/Change Diagram
From $5.00
Make a selection 911631620AA Triangular 1975-76 model, these lights are often neglected until the cops stop you! Check yours today and remember, when connecting, brown is ground and connects to the body of the light. Note: remember that brown is ground and connected to the body of the license plate assembly. If you mis-connect the wires, you will burn out the wiring harness.
$6.99
Make a selection 91164190200 As your original instruments rubber ages, it dries out and becomes brittle. We recommend changing out your instrument rings when servicing your instruments or swapping your instrument faces. Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per car. View/Change Diagram
From $5.71
Make a selection 91462843300 T junction valve to route washer lines. Sold individually. View/Change Diagram
From $6.80
Make a selection 915300911550 If you are looking for a transmission oil cooler system that is simple to install, provides lasting results and is perfect for a driver, the weekender, or for track use look no further. This kit includes a sleek high-performance oil cooler that mounts simply to the transmission cover with the included bracket and hardware. The stainless braided lines seamlessly screw into the transmission housing drain / fill plug location, no modification required. The electric, self-priming, 12 v oil pump is made with helical bronze gears, a stainless-steel shaft and a nickel plated brass body for the reliability that you expect from your Porsche. The pump includes a bracket that allows for simple installation. Simply connect...(choose a part on the right to read more)
$1,529.00
Make a selection 92811014711EQ Today's fuel has a myriad of oxygenate additives to comply with more strict emissions standards. These additives can be detrimental to your investment. Certain additives can break down rubber components in the fuel system. Others like ethanol are hygroscopic, so they absorb water. Ethanol is also an alcohol, so it tends to clean out more impurities which tends to foul the fuel filter far more quickly than fuels of the past. So, keeping the above in mind, we suggest replacing your fuel filter far more regularly. This is a high-quality replacement filter sourced directly from Germany. Sold individually.
$52.80
Make a selection 93010190200EQ2 Quality aftermarket replacement, designed to perform like the original. Includes a threaded drain plug cut out and drain plug. We also recommend replacing the gaskets for installation, part # 93010139101 sold individually. 1 necessary per car.
$48.00
Make a selection 93010590201EQ Attention: the 911 SC 3.0 liter only for vehicles without oil drain cover. This kit contains everything needed for a valve adjustment. High-quality victor reinz gaskets with hardware, designed to perform like the original. We source this kit in Germany to ensure quality, reliability and precise fitment. Set includes: 2 qty. Lower valve cover gaskets 93010519507 2 qty. Upper valve cover gaskets 93010519404 34 qty. Valve cover nuts 34 qty. Valve cover washers sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$52.80
Make a selection 93011013900EQ Today's fuel has a myriad of oxygenate additives to comply with more strict emissions standards. These additives can be detrimental to your investment. Certain additives can break down rubber components in the fuel system. Others like ethanol are hygroscopic, so they absorb water. Ethanol is also an alcohol, so it tends to clean out more impurities which tends to foul the fuel filter far more quickly than fuels of the past. So, keeping the above in mind, we suggest replacing your fuel filter far more regularly. High-quality OEM Bosch replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually.
$51.70
Make a selection 93011601402 Made in Germany by sachs to original specifications. Direct replacement for the oe clutch disc. Torsion sprung. Discs with torsion springs function as a vibration damper between the engine and gearbox. They effectively lessen the harshness felt during re-engagement. Please note: we always recommend replacing the pressure plate, clutch disc, throw out bearing and starter ring gear at the same time. View/Change Diagram
From $248.60
Make a selection 93011606406 These helper springs tend to wear out with time and mileage which gives the sensation of a failing clutch. We recommend replacing this in conjunction with the clutch cable and any new clutch installation. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. View/Change Diagram
From $105.00
Make a selection 93034732200 If your outer tie rods are worn, you will experience sloppy steering response and knocking / creaking sounds. Your outer tie rods keep the steering centered, so failure can be dangerous and can seriously affect steering control. After replacing the tie rods, you will experience tighter, more precise feedback without noise. Tie rod end consists of: 1 qty. Ball joint end 1 qty. Dust bellows / boot 1 qty. Hexagon lock nut 1 qty. Lock nut washer 1 qty. Pin high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. We recommend replacing the right and left side tie rod ends at the same time....(choose a part on the right to read more) View/Change Diagram
From $13.95
Make a selection 93060201501 Complete distributor without an exchange. This distributor has been completely remanufactured, which includes a full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt, 3 German made top bearings, 1 German made lower bearing and a distributor pinion pin (part # 930 602 922 00). We also install new dust caps, Bosch rotors and Bosch cap. Clearances, timing and proper operation are then checked to ensure reliability.
$2,534.48
Make a selection 93060610500ATK The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, clean, degrease and rebuild to factory specifications. Remanufacturing is done in Germany, so the lead times can vary. Send us your original warmup regulator and we will have it remanufactured for you. We do not offer a core exchange on this part. Please note: please package your part as carefully as possible to ensure that damage is not caused en route to us.
$744.70
Make a selection 96410524609ST This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$1,441.00
Make a selection 96410524707GU This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$932.80
Make a selection 96434703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. This is ideally suited for use with our monoball inner tie rod, part # 96434705805sp for the 964 c2 / turbo look or 965 or part # 96434705804sp for the 964 c4 or rs. Please note: this is not for the wide body. Sold indiv...(choose a part on the right to read more)
$322.21
Make a selection 96434101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection 96434705804SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. We also suggest replacing your outer tie rods, part # 96434703200 (qty. 2 are needed) and now is also a good time to replace your worn out inner tie rod dust bellows, part # 96434719103. Please note: this is not for the ...(choose a part on the right to read more)
$196.90
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 964565035017EQ This is genuine targa top material sourced from Germany. It is as close to the original as possible and is cut and trimmed to fit perfectly. We also make sure that there is plenty of material to stretch out the sides so that there are no wrinkles when installed. Sold individually. 1 necessary per car.
$335.50
Make a selection 96453705700SET If you are hearing a crunching or creaking noise when you close your door, start by replacing your door check / door arrester. It prevents the door from opening to widely or slamming. As our cars age, they wear out and start to become very noisy. We also recommend replacing the door check bolt, and safety clip, so we have created an complete set for one door - repair sold individually. Left of right side fitment. 2 needed per car.
$64.13
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |