Vehicles
Sections
401 not categorized PORSCHE 944 IMS CHECKCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 944 1982-85 (includes uncategorized and accessory items) 95B615601GBZ Die zimmermann bremsscheibe black z wurde auf basis der erfahrungen von serienfahrzeug-bremsscheiben in verbindung mit dem einsatz im rennsport, speziell in der vln, entwickelt. Die bremsperformance erfullt die hohen anspruche aus dem rennsport und kann nun auch im strassenbetrieb erlebt werden. Wie bei allen zimmermann-scheiben werden auch hier nur hochwertigste gussqualitaten eingesetzt. Die vorteile:•schnelleres ansprechen der bremse durch die optimierte ableitung von wasser •besseres nassbremsverhalten •gebrauchsmuster geschutztes nutbild sorgt fur optimale warmeableitung und damit verbesserung der bremsleistung •bremsenfading wird vermieden •coolere optik •bessere optik ...(choose a part on the right to read more)
$185.90
Make a selection 96410541903EQ When working on your cylinder head, we recommend replacing the valves, valve seat rings, guides, springs, retainers and temperature sensor at the same time to reduce future labor costs. Cost effective, German made exhaust valve for the 964 c2 / c4 and rs that have the m64.01/02/03 motors. Sold individually. 6 necessary per car.
$64.90
Make a selection 95B615601GSPORT Die zimmermann sport-bremsscheibe wurde auf basis der erfahrungen von serienfahrzeug-bremsscheiben in verbindung mit dem motorsport entwickelt.durch die kombination hochwertiger gussmaterialien mit einer gelochten bremsflache wird eine optimierung des bremssystems erzielt.die vorteile: besseres nassbremsverhalten bremsstaub und wasser werden permanent abgefuhrt sportlichere optik spurbare verbesserung der bremsleistung ihres fahrzeuges bremsenfading wird vermieden die ansenkung der bohrungen dient gleichzeitig als verschleissanzeiger austausch der originalscheibe 1:1 moglich
$129.80
Make a selection 96434101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection 96434101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 018 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 96434307181ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$194.70
Make a selection 96434705805SP We are committed to Porsche cars and are very happy to release an inner tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 058 05. We also suggest replacing your outer tie rods, we have a uniball option, our part # 96534703200sp or the OEM style, narrow body is part # 96434703200 or wide body is part # 96434703201 (qty. 2 are needed) and now is also...(choose a part on the right to read more)
$207.90
Make a selection 96434101707AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 017 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 96437502301RATK Send us your OEM transmission mount bracket and we will restore it to better than new condition! Our service includes removal of the old mount, media blasting, proper installation of the new mount and protective seal coating. Our transmission mount is manufactured in europe by an OEM supplier using the finest materials (high carbon steel, 7075 t6 aluminum and 85 shore rubber - rs spec). Simply order and send us your OEM bracket, we will take care of the rest. Approximate lead time is estimated between 3-6 weeks.
$176.00
Make a selection 96450204100EQ Quality replacement part for original number, 964 502 041 00 grv. This is made by dansk, they offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality, factory fitment and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. The inner mount is adjustable to properly attach / adjust the striker plate. We recommend adding new striker plates and striker plate gaskets, left side striker plate is part # 99353102901 and the gasket is either 90153170323 or 90153170324 depending on what thickness you need. ...(choose a part on the right to read more)
$107.80
Make a selection 96450113500EQ Quality replacement part for original number, 964 501 135 00 grv. This is made by dansk, they offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality, factory fitment and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. Driver's side fitment. Fits 911 models from 1966-94. Please note: due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$133.10
Make a selection 96450501800 This support assists in absorbing impacts and supports the bumper reinforcement bars. Sold individually. 2 necessary per vehicle.
From $103.40
Make a selection 964541225001 This genuine Porsche windshield seal is an integral part of keeping your cowl from rusting. It is critical that the gasket and windshield are properly installed to prevent corrosion. Sold individually. 1 needed per car. Please note: for the 911 models, this does not contain the trim frame slot for chrome / black trim like the earlier cars.
$406.00
Make a selection 96455550700EQ A-pillar lining made of original leatherette material, sourced and manufactured in Germany. Each is cut, sewn and trimmed for precise fitment. We go to extra lengths to ensure that our linings are as similar to the originals as possible. Replaces original part # 964 555 507 00 05t made in Germany. Sold individually. 1 necessary per car.
$94.60
Make a selection 96455583200LIL Attention to detail is what distinguishes our parts from the competition. We source these door pulls in Germany to ensure that the material and stitching are made as closely to the originals as possible. This is a shade similar to the original rs lila (German). Sold individually.
$18.70
Make a selection 964561005016HA This is a complete cabrio top made in Germany with original sonnenland material. It is as close to the original as possible and is cut and trimmed to fit perfectly. Includes a trapezoidal pvc plastic rear window with a zipper like the original. If the window gets hazy simply unzip, remove and add a new window. Sonnenland material consists of 3 layers, dyed acrylic twill weave top layer, elastomeric rubber inner layer and polyester woven base layer. It provides increased strength against abrasion, increased fade resistance and the tighter woven layers are made for modern electric tops with stronger frames, like the 911 and 964. Sonnenland high quality material was originally used by Porsche and other top German ...(choose a part on the right to read more)
$2,201.10
Make a selection 96534703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM part number, 965 347 032 00. Sold individually. 2 needed per car. We also suggest replacing your inner tie rod, we have a uniball option, our part # 96434705805sp (qty. 1 is needed) and now is also a good time to replace your worn out inner tie...(choose a part on the right to read more)
$251.90
Make a selection 98633305130 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber for your Porsche with m030-sportsuspension. The b4 damper from bilstein is the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
From $367.50
Make a selection 98634304136 Bilstein b4 OEM (original equipment manufacturer) replacement shock absorber for your Porsche with m030-sportsuspension. The b4 damper from bilstein is the perfect replacement for your Porsche. Facts: - constant damping power under any load - high power reserves for maximum safety - ride like it's the first time, every time - OEM quality - bilstein gas pressure technology
From $326.69
Make a selection 99157311104 Condensers release heat from the a/c system, by transforming gas into liquid to absorb heat. Condensers can suffer from internal clogging, seams leaking or can be plugged or damaged by road debris. Be sure to replace as needed to keep the hvac system operating perfectly, especially after a compressor failure. When replacing the condenser, we also recommend replacing o-rings, part # 99970755741 this is a high-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. Left or right-side fitment. 2 necessary per car. Please note: need a part that is not listed on our site? Si...(choose a part on the right to read more)
From $223.30
Make a selection 99310541906EQ Exhaust valve for 993 models from 1996-98 with m64.21/22/23/24 motors. 8 mm stem, 43.5 mm, weighs .22 lbs. (.1 kg). Sold individually. 6 necessary per car. When working on your cylinder head, we recommend replacing the valves, valve seat rings, guides, springs, retainers and temperature sensor at the same time to reduce future labor costs.
$73.70
Make a selection 99312301352ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, install new waste gates, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turboc...(choose a part on the right to read more)
$2,194.50
Make a selection BES99104060S + 11 hp & + 10 tq gain. - 2 3/4 tubing (70mm). - weighs 35.2 lbs (16 kgs) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - includes block off plates & caps to use with either the OEM center muffler or an aftermarket center muffler bypass (with 2 inlets). - replaces the OEM valved side mufflers. Connects to OEM header and catalytic flange and connects to OEM center muffler or bypass. - can be used with bes99107060s1 for an even more aggressive growl. * please note - you will no longer have use of your valves ! Our 991 GT3 side muffler replacements are vastly different than the baffle plated mufflers stu...(choose a part on the right to read more)
$1,788.60
Make a selection 99334101702ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install original control arm bushings. . Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part. Sold individually....(choose a part on the right to read more)
$418.00
Make a selection 99335512901EQ Classic Porsche flexible brake hoses can suffer from dry rot and can eventually split and leak fluid, creating a serious safety concern. This line is a high quality replacement, designed to perform like the original and has the same length and threaded ends. It also includes a rubber support grommet and shield just like the original. We recommend inspecting all of your brake lines and hoses the next time you change your brake pads. Sold individually. 2 necessary per car. For 1995 -1998 models.
$19.80
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |