PORSCHE CAYMAN DEL SOLCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 944 1985-88 - Front Axle/Steering (includes uncategorized and accessory items) FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection BES97005080S11 Brombacher panamera s & 4s "sound version" sport muffler - 10 crank hp & + 9 crank torque. - 2.5'' tubing (63,5mm) straight through design for maximum power. - 11 lb. Weight savings. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - quad 4'' (100mm) round tips sold separately for basic OEM systems (without Porsche sport exhaust)* - tips can be individually adjusted for personal taste. - deeper tonal quality and louder volume which enhances 4.8 l Porsche sound.** - no ecu (software) programming necessary. - will work with OEM exhaust components. - absolutely no drone in the cabin. - does not interfere with emissions and will not trigger the check engine light. - made in Germany...(choose a part on the right to read more)
$2,476.10
Make a selection FVD11GK181GF Motorsport quality grp (glass-reinforced plastic) front bumper bar. Features: - produced by an German motorsport manufacturer. - lightweight 5.7 lbs. (2.6 kg) - made of high strength, grp (glass-reinforced plastic) sold individually. 1 necessary per car. Please note: please provide us with the year / model. These are motorsport quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. All grp products must properly be fitted and completely prepared prior to paint.
$559.90
Make a selection FVD10699710 This radiator is produced by the racing & high-performance division of csf who design, engineer and manufacture the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers all aluminum high performance radiators that are a direct-fit replacement for Porsche racecars and streetcars. Csf radiators improve cooling efficiency by 10-20 % over the factory radiators. Each radiator is stamped to the same geometry and includes aluminum end tanks that offer more reliability than the factory plastic end tanks. Each csf end tank features quality welding and is generally considered the strongest tank design in the industry. If you are planning to upgrade or replace your radiators, we highly re...(choose a part on the right to read more)
$526.90
Make a selection BES98215000SK Brombacher edition valved mufflers are the perfect compromise for you and your loved ones. Rich, deep race car tones with the exhaust valve open and soft subtle, nearly stock sounds with it closed. + 17 hp & + 13 tq gain. - 2 x 3.5 (90 mm) round tips. - includes a pierburg vacuum actuated exhaust valve. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - intoxicating growl at idle, partial throttle and wide open throttle with the valves open. Factory quiet with them closed! - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport muffler connections to ensure a leak free exhau...(choose a part on the right to read more)
$5,309.70
Make a selection FVD34101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$154.00
Make a selection FVD3310212291 Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. -includes press tools and grease for easier assembly. Sold as a set. 1 kit is necessary per car. Please note: this fits the 964 c2 / c4 and rs america. Not keen on installing or having the bushings installed at a shop? Please check out our part # FVD33399603b8 and FVD33399603b8, we wil...(choose a part on the right to read more)
$902.00
Make a selection 99157362300 A clean cabin air filter reduces dust, dirt, allergens and odor. It will also increase the airflow from the cabin vents. Be sure to replace yours as recommended to keep consistent air quality. High-quality mann OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment since this fits multiple models / applications. We also recommend replacing the exterior cabin air filter, part # 99157237100
From $22.25
Make a selection 129T851852 The rh turbo style Porsche wheel is a classic design perfectly suited for any Porsche model. The center section is cast aluminum and finished in a silver paint. The wheels come with standard rh center cap and accept factory Porsche wheel bolts and center caps. The wheels are offered in 17 and 18 with a variety of offsets to fit narrow and wide body Porsche applications. These wheels are made to order and take between 1-3 weeks to deliver. We recommend ordering a set of rh valves, part # 12945281 when ordering this wheel. Please note: if you are installing these on a 928, body work will be required. Sold individually.
$342.10
Make a selection FVD201911964993 Looking to update your fuel cap? This is a cost effective, sporty, aluminum alternative to the factory cap. It resembles the tequipment cap available on the water-cooled models. It is a quality tuning product manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Oem non-locking, screw type fuel cap sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary ...(choose a part on the right to read more) General FitmentACCESSORY
$136.40
Make a selection FVD361900715EU This fuchs replica is a classic design perfectly suited for any Porsche model. The center section is cast aluminum and finished black with a layer of clear coat. TUV approval documentation is standard with each wheel. The wheel accepts factory Porsche wheel bolts and center caps. Center caps sold separately, part # 190361035 or 190361033 sold individually.
$410.30
Make a selection FVD33399300 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of TUV certified eibach springs. This suspension kit will lower the front axle to a maximum of 35 mm (1.37 inches) and the rear axle to 30 mm (1.18 inches), like the European rennsport model. The height is adjustable as the dampers are threaded. They are a cost effective solution for clubsport use and will be well mannered on the street. Sold as a complete kit. 1 kit is necessary per car.
$11,872.30
Make a selection FVD207052 This is meant for g models with 3.0 l rs/ rsr front bumpers. It is ready for installation with oil cooler, oil hoses and mounting brackets. The oil cooler is a high-quality OEM replacement, designed to perform like the original. We source these parts in Germany to ensure quality, reliability and precise fitment. Sold as a kit. 1 necessary per car.
$1,887.60
Make a selection FVD10699701 This radiator is produced by the racing & high-performance division of csf who design, engineer and manufacture the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers all aluminum high performance radiators that are a direct-fit replacement for Porsche racecars and streetcars. Csf radiators improve cooling efficiency by 10-20 % over the factory radiators. Each radiator is stamped to the same geometry and includes aluminum end tanks that offer more reliability than the factory plastic end tanks. Each csf end tank features quality welding and is generally considered the strongest tank design in the industry. If you are planning to upgrade or replace your radiators, we highly re...(choose a part on the right to read more)
$548.90
Make a selection FVD50399101MM The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)
$3,631.10
Make a selection FVD50501901 When installing a lightweight bumper or bumper bar for racing use, you want to remove as much weight as possible. Don't forget to remove your heavy factory supports. This is a lightweight aluminum alternative, made in Germany. Weighs: 140 grams / .13 kilograms / .3 lbs. Sold individually. Please note: please check the model fitment tab to ensure accurate fitment.
$141.90
Make a selection FVD72269500LGW This simple FVD Brombachertow hook installs in seconds and folds down to eliminate protrusion from the car's bodywork. It fits all Porsche's with factory left hand thread, screw-type tow hooks. It has a two-inch towing eye, which is required for track events. It is precision cnc machined stainless steel, tig-welded, has a polished shaft and a rubber locking rod to prevent loosening. Features: stainless steel light weight: 1.6 lbs. Fits any Porsche listed in our fits these models tab. Installs in seconds, simply remove the bumper plug and screw into the tow hook hole. Made in Germany. Includes FVD Brombacherlogo. Sold individually.
$137.50
Make a selection RES98720000SS Having to weld up cracks regularly on your current aftermarket racing exhaust? If you are looking for a racing exhaust that can handle abuse at the track, look no further. This exhaust system is manufactured by m&m exhaust, gmbh in Germany. They manufacture a multitude of Porsche motorsport and racing exhausts. Each system is designed for reliability and performance gains throughout the entire rev range. Not to mention, you directly benefit from everything m&m learns at the track, so their systems designs are never static. Also, each system is tested comprehensively for flow characteristics / rate, thermal stress, cracking, and longevity. Features: + 20 hp & + 19 tq catalytic bypass pipes weighs 55 lbs. (23 kg)...(choose a part on the right to read more)
$5,082.00
Make a selection FVD50193500 Steel, prime coated floor pan repair panel made by dansk. They offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to European standards to ensure the quality that you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. 1 necessary per car. Please note: due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$316.80
Make a selection FVD51299124MM The moshammer stormforce evo rs rear spoiler for the 991.2 model blends a bit of Porsche ducktail heritage into its design to increase rear downforce and reduce front axle uplift. The contours of this spoiler have a step effect which seamlessly blends into both rear quarter panels. When viewed at a standstill it has a subtle factory like appeal that complements the cars lines. When deployed the rake angle takes on a more aggressive appearance evoking thoughts of the much beloved ducktails. Like a majority of the moshammer offerings, this spoiler is a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looki...(choose a part on the right to read more)
$1,455.30
Make a selection FVD50599102MM The moshammer evo 2 front chin spoiler blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce. Porsche active aerodynamics remains fully functional in all 3 positions and the evo 2 chin spoiler secures seamlessly into the factory locations. The evo 2 spoiler's design offers a more aggressive look but also blends perfectly with other design elements like the side skirts and rear spoiler. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of either the evo rs (991.2 turbo/s) or downforce rs...(choose a part on the right to read more)
$1,386.00
Make a selection FVD362041002 High quality wheel nut and lock set. The set includes a key and teflon insert for your lug tool so the nuts will not be marred when removed. Please check the exact model designation for this part below. Sold as a set. 1 necessary per car.
$35.20
Make a selection RES99600060SC Race exhaust system 996 GT3 cup, stainless steel, cat bypass with tips facts: - + 25 crank hp & + 19 crank torque - catalytic bypass - long tube headers 3 x 50mm (1.97") tubes into a 70mm (2.75") collector for max. Torque - does not exceed 106db - weighs 51 lbs. (24 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability - cone style connection design to prevent exhaust leaks - includes aeroquip quick release clamps - made in Germany - can be ordered with race cats. Please ask your FVD sales representative for details. FVD is proud to introduce our newest line of Brombacherrace exhaust systems. Brombacher race exhausts are engineered for the discerning Porsche owner and offer unmatche...(choose a part on the right to read more)
$6,350.30
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |