PORSCHE 924 S SILL RIGHTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 968 1992-95 - Electrical (includes uncategorized and accessory items) FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection 99335140787 This was the rotor used on the 964 cup / rsr / 964 cup / rsr / 993 cup / rsr / GT2 evo. This disc is a genuine motorsports replacement part. It is drilled and vented. Sold individually. The corresponding right side is part # 99335140887 all motorsport and racing parts are special order items. Special order items must be paid for in advance. Special order items are sold on a non-cancelable, non-exchangeable, non-returnable, non-refundable basis and do not carry any warranty. No exceptions.
$721.60
Make a selection GR5006 Leather upholstery belongs in all fine cars. It just smells and feels right. Preserve your expensive handsome interior with the best! Lexol cleaner is ph balanced, so even with its fantastic cleaning abilities, it will not cause your leather to dry or crack. A good cleaning should then be followed with lexol conditioner to restore the suppleness and keep the leather from drying out (especially in the summer sun). General FitmentACCESSORY
$13.49
Make a selection FVD512997TTRS 997 GT3 rear spoiler fits all 997 tt includes: deck lid, aluminum upright, 3rd brake light housing and wing (l= 145cm, b=28cm, h=7 cm) with end plates. Material: aluminum, fiberglass. Also available with wing blade in kevlar / carbon FVD512997gt3rs2 tech tip: facelift models (2009- ), the 3rd brake light can usually be assumed. If necessary please order the 3rd brake light 99763105201 separately. The holes for the intake fan on the rear deck lid must be drilled prior to installation (model variations). Please note wing is fixed and is not adjustable. The air inlet of the rear is not included. Please order 99751262592g2x
$5,407.60
Make a selection FVD20798700 This FVD motorsports oil pump kit is a must for 987.1 Caymans and Boxsters driven on the track. Our kit includes a second return oil pump and our FVD motorsports oil pan. The issue: the 987.1 Boxster/Cayman from 2005 to 2008 has the factory return oil pump located on the right rear side. On the left side, the return oil pump located in front. So when driven fast in right turns, the oil from the camshaft case (rear left) does not flow back quickly enough into the oil pan. When the oil pan is starved of oil, the oil pump sucks in air and over time the motor will seize. The solution: our tandem return oil pump draws oil from the camshaft housing in (rear left, 3rd cylinder) and feeds it back into the oil pan so th...(choose a part on the right to read more)
$3,274.30
Make a selection GR6031 Nothing ruins the appearance of a sharp set of wheels like dirty, corroded calipers lurking from behind. General FitmentALL
$40.95
Make a selection GR6032 Nothing ruins the appearance of a sharp set of wheels like dirty, corroded calipers lurking from behind. General FitmentALL
$40.95
Make a selection CB43201B Corbeau 2 inch double release harness belts are unique in that they have a disconnect feature between the front shoulder straps and the rear tail strap. This feature allows for easy access to the rear seat as you can disconnect that rear strap without taking the belts out. They also have the rare ability to be bolted to all your factory provided mounting points. What that means is all our hardware was manufactured to bolt right up to your factory bolt holes. In most cases no drilling or modifications are necessary, they just bolt right in. Corbeau 2-inch double release harness belts are available in a 3 point style with bolt-in mounting. General FitmentALL
$169.00
Make a selection FVD34307201 Our direct replacement, OEM quality link uses rubber with a shore hardness value of 85. That is the same value as the rennsport models from Porsche. This link will offer superior performance under high cornering loads, more durability and are still forgiving for street use. Road noise not compromised with our links either. Facts: made in Germany. Crafted from high carbon steel and 7075 t6 aircraft aluminum. Weather sealed. Sold individually. Please note: we recommend buying these as a set, please purchase the left link, our part # FVD34307101
$93.50
Make a selection FVD424049ER If you are using numeric racing performance cables on your race car, then we suggest upgrading your rod ends to these steel ends which will take far more abuse at the track. These are recommended for race cars only as metal on metal contact means increased noise and vibration in the cabin. Sold individually.
$22.00
Make a selection FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection 91153170202 As a striker plate ages, it will start to rattle and can potentially be a safety risk. We recommend securing them with new oval head screws, part # 99921900800. 2 screws are needed per plate. We also recommend adding new striker plates gaskets, either 90153170323 or 90153170324 depending on what thickness you need. This line is a high-quality replacement part, sourced in Germany and designed to perform like the original. Sold individually. 1 necessary per car.
From $133.10
Make a selection 115343993008R If you are looking for a shock to combine with lowering springs or firmer springs the bilstein b8 is the ideal solution. These offer more performance than the b6 as the valving is more firm. These will pair well with h&r or eibach lowering springs, however you can also run them with euro mo30 (row) springs and mo33 springs. The product benefits at a glance: shortened high-performance shock absorbers for virtually every lowering spring set. Marked improvement in safety and sportiness with additional spring changes (lowering). Sporty feel, yet still comfortable. Offers precise handling and optimum control. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Road-tested an...(choose a part on the right to read more)
$524.70
Make a selection FVD34101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection 91163194000EQ If you are restoring or replacing a rear taillight, you may want to consider this. It is a lightweight, high-quality OEM replacement, designed to perform like the original. Perfect for a race application, or for a lightweight street car. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. Passenger's side fitment. 1 necessary per car.
$320.10
Make a selection 92834102833ATK By ordering this part number you get after previous sending in your wishbone overhauled with new silent blocs back. Should it not be repairable, we will inform you immediately.
$342.10
Make a selection 96434307281ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$194.70
Make a selection 99333105280 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $764.50
Make a selection 96453109600EQ This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.
$215.60
Make a selection 96455550800EQ A-pillar lining made of original leatherette material, sourced and manufactured in Germany. Each is cut, sewn and trimmed for precise fitment. We go to extra lengths to ensure that our linings are as similar to the originals as possible. Replaces original part # 964 555 508 00 05t made in Germany. Sold individually. 1 necessary per car.
$94.60
Make a selection FVD123048 FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$6,413.00
Make a selection FVD11104001 These headers are meant to replace the original 993 GT2 r (993 111 039 83) headers that are no longer available. They will reduce turbo lag and add horsepower and torque. Made of t316 stainless. Primaries are 42mm (1.65 ). Merge into a 50mm (2 ) motorsports collector. Manufactured by m&m exhaust in Germany.
$1,835.90
Make a selection 150PT356912 This model is the first of a brand new product line for perma-tune. We have combined our accumulated knowledge of Porsche ignition over the last 48 years and applied it to the very latest electronics technology to produce a state of the art electronic ignition module that is period correct looking. Made to look like an old school electrical relay, it blends right into the engine bay of a 356 or an early 911. No crimps, no mess, no headaches plug and play features eliminate the need for wire crimps and complicated wiring diagrams. Wires are cut and stripped, then inserted into the wire bus for a secure, plug in connection without the need for special tools or wire crimps. Simple, four wire installation. There is...(choose a part on the right to read more)
$762.30
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |