Vehicles
Sections
151 not categorized PORSCHE 924 WIL VICan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 968 1992-95 (includes uncategorized and accessory items) 12637023CSR Power slot rear right cryogenic slotted rotors Porsche 964 Carrera 2 2s 90-94 General Fitment911 1989-94944 1985-88 944 1989-91 968 1992-95
$186.15
Make a selection 12637023CSL Power slot rear left cryogenic slotted rotors Porsche 964 Carrera 2 2s 90-94 General Fitment911 1989-94944 1985-88 944 1989-91 968 1992-95
$186.15
Make a selection 93061221102 When your pads reach a critical level, these sensors will trigger a warning to alert you that your pads need to be changed. Be sure to purchase these in conjunction with your new brake pads. High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 2 necessary per axle.
From $13.02
Make a selection 95037005 Stoptech brake lines consist of a ptfe (commonly referred to as teflon) inner line that carries the brake fluid, which is then covered with a layer of stainless steel woven braid. The ptfe tube is very resistant to expansion under pressure and will not degrade from exposure to brake fluid. every stoptech brake line is 100% tested in-house to a pressure of 4,500 psi. This is almost 4 times the typical line pressure exerted by a production vehicle's master cylinder. stoptech is a registered brake line manufacturer with the united states DOT and all stoptech stainless steel brake lines are manufactured to meet DOT compliance standards. Stoptech stainless steel lines also meet or exceed fmvss 106 and applicable...(choose a part on the right to read more) General Fitment944 1989-91968 1992-95
$112.74
Make a selection 220110908ATK 63,24mm ! (original 60mm) more air = more performance we will need for this rebuild your own part first to work on that. Please contact us before shipping for the rma number.
$485.10
Make a selection 21011123 Catalytic bypass pipe "x torque" design made by m&m in Germany. The x torque design in is a true x pipe design. It is open in the center to add backpressure for torque. Give's you 10-15 ft-lbs of torque in the mid range along with 10-15 hp in the higher rpms. Why settle for the traditional cross over cat design when you can add torque in the mid range where the 996's need it most! Dme programming is necessary. Without it you will get a check engine light (cel). Tech tip: for older cars repair-kit FVD mk 996300
From $764.50
Make a selection 150SPB976 Replace worn-out spring plate bushings with these longer lasting poly-graphite plastic bushings. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This includes the inner and outer bushing for the 2-piece adjustable spring plate. Sold individually. 2 necessary per car.
$39.60
Make a selection 4440448006005AK High quality polished switch cover. Send us your original cover and we will install the carbon for you. We do not offer a core exchange on this part. Great detail is taken to attempt to match the original weave size, color and polish. Whether you are adding carbon to the interior or matching existing pieces, this is high quality and is made in Germany so it is made to last, like the original. Please note: knob is not included. It is not necessary for you to send us your knob. Sold individually. We also recommend replacing your missing or broken switch cover clips, part # 94455255700. 2 are needed per switch cover. If you would also like to replace the knob, use part # FVD33399603b8
$553.41
Make a selection 21011196402 Say good bye to the days of having to weld and cut aftermarket sport cats to make them fit! We have our sport cats made in Germany to our specifications and that means that these are 100% bolt on without issue! - + 10 crank hp & +6 crank torque. - 200 cell, tri metallic German hjs sport catalysts. - large volume o 105 mm (4.1 inch diameter) high flow cat. - exhaust hanger brackets are included so that the heat shield does not have to be removed. - weighs 7.2 lbs. (3,2 kg). - direct bolt on replacement. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress. - made in Germany. - more distinguished flat 6 growl at wide open throttle. The FVD 200 cell...(choose a part on the right to read more)
$1,593.90
Make a selection 150PB10134 Replace worn-out original sway bar drop link bushings with this longer lasting poly-graphite plastic bushing set. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. The set includes 4 complete bushings and 4 sleeves (8mm inner diameter). Sold as a set. 1 necessary per car.
$73.70
Make a selection 190111043B For use on obd1 (94 and earlier) cars only! Only 1 o2 bung is provided. Call for 1995 application. Will not work with multiple o2 sensor cars, like north american cars. (96-98) does not include a TUV-certificate. We recommend using our catalytic installation kit, part # FVDmk993300b please note: not legal for use on california pollution controlled motor vehicles.
$556.60
Make a selection 190111043G For use on obd1 (94 and earlier) cars only! Only 1 o2 bung is provided. Call for 1995 application. Will not work with multiple o2 sensor cars, like north american cars. (96-98) does not include a TUV-certificate. We recommend using our catalytic installation kit, part # FVDmk993300g please note: not legal for use on california pollution controlled motor vehicles.
$705.10
Make a selection 150TBR900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the front of the control arm is part # 150tbf900 sold individually. 2 necessary per car.
$49.50
Make a selection 2009010233 Performance eproms can increase horsepower. After replacing the chip in your Porsche’s engine you will immediately notice the advantage. Some chips require that you send your dme and others are plug-ins. Please ask when ordering. General Fitment968 1992-95
$450.00
Make a selection 47085150 This is a universal air filter system that can replace your restrictive air box and filter. The carbon-air box improves the volume of air and increases the velocity. In some applications it can increase horsepower up to 25 ps (23 hp) and will also provide you with better throttle response. It is a universal filter and can be used on most vehicles in place of the original air box (with modifications, if necessary). This filter is not typically intended for street use and is designed for race use. Not for Boxster s, 993tt, GT2! Please note: sold individually. Dual intake systems will require two units. Specifications: 85mm, does not include a sensor cut out.
$354.20
Make a selection 1159029964WD The ohlins road & track suspension gives our customers a true racing experience, with their own cars, without losing comfort when commuting to work. Our unique dual flow valve (dfv) technology allows you to quickly change the stiffness of the shock absorber. When arriving to the racetrack, just turn the golden knob clockwise on the damper to set it in race mode this action changes all four areas in the damper; low and high speed compression and rebound damping. With ohlins road & track coil overs you will experience a car with blistering response times, improved bump absorption and a massive amount of grip to increase the safety when driving your car on the limit. The car will be easier to balance on the edge o...(choose a part on the right to read more)
$5,635.30
Make a selection 100498F60104 Looking to move your formula steering wheel (930 s wheel) closer for more leverage, quicker steering corrections or comfort? This spacer ring will move the formula wheel 1" (25 mm) closer. Sold individually. General Fitment911 1994-98968 1992-95 911 1989-94 944 1982-85 944 1985-88 928 1992-95 924 1980-85 914 1970-76 911 1970-73
$162.80
Make a selection 115333993008 If you are looking for a shock to combine with lowering springs or firmer springs the bilstein b8 is the ideal solution. These offer more performance than the b6 as the valving is more firm. These will pair well with h&r or eibach lowering springs, however you can also run them with euro mo30 (row) springs and mo33 springs. The product benefits at a glance: shortened high-performance shock absorbers for virtually every lowering spring set. Marked improvement in safety and sportiness with additional spring changes (lowering). Sporty feel, yet still comfortable. Offers precise handling and optimum control. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Road-tested an...(choose a part on the right to read more)
$343.20
Make a selection 1150009 These are made with club sport events in mind. They work with stiffer springs and lowering springs (we recommend h&r or eibach) and have a fully threaded body for individual lowering like the original 993 cup suspension. You will need to run our drop links for the sway bar, part # FVD333900. Lowering is adjustable to 30 mm (1.18 inches) left or right side fitment. Sold individually. For matching front club sport shocks, please order part # 1150002li for the left and part # 1150002re for the right. For a properly spec'd complete kit including front and rear club sport shocks with lowering springs and rear drop links, please order part # FVD33399300.
$382.80
Make a selection 94331600100ATK Send us your tired original torque converter and we will rebuild it to new specifications. Contact us today to find out the exchange details.
$1,788.60
Make a selection 477253121B This is the front muffler for all 76-85 Porsche 924 models. It was original equipment before the cat and will replace it as well. great for the extra performance and quiet exhaust you expect from your 924.
From $112.20
Make a selection 2699 The wrench is flat and wide and was designed to hold a tensioner pulley in place while the retaining nut is applied. The retaining-nut usually over hangs its base therefore the wrench has to be flat. No conventionally sold metric key-wrench will clear the base for the retaining-nut installation. Do not look for something else. It was tried before you. It just will not clear. Two types of tensioner pulleys are used in 924-944 today. The metal tensioner pulley and the plastic tentioner pulley.
$43.99
Make a selection 220110908 63,24mm ! (original 60mm) General Fitment968 1992-95
$485.10
Make a selection 100211025SSUSA If you have a us model 1980-83 911 SC and are looking to replace your heat exchangers we have some good and bad news. The original heat exchangers (part # 930 211 025 02) are no longer available from Porsche. But, these stainless-steel industries (ssi) heat exchangers will work with modifications. The good news is, once done, you will have more torque and horsepower! Free flow conversion heat exchangers improve sound and performance, while reducing backpressure and thermal load on the motor. These are based off the early style exhausts found on the 1974 2.7 l rs. Those models had a straight through, superior, free flow exhaust design that included a dual inlet muffler. When converting to these heat exchangers y...(choose a part on the right to read more)
$2,863.30
Make a selection 914301GT For 7” and 9” flares.
$229.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |