![](https://30ed524141d0cac60ab4-d2e2d18a14257de3b9ce428cf077ee97.ssl.cf2.rackcdn.com/acban.jpg)
401 not categorized PORSCHE 356B REAR LEDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: BOXSTER 1997-04 - Uncategorized (includes uncategorized and accessory items) ![]() FVD803993VS0222 High quality, German made three-point replacement safety belt, designed to perform like the original. Features / specs: belt length: 300 cm (118 inches) 3 point inertia reel belt angle adjustable reel (max. Of 8 *) includes 22 cm (8.5 inch) buckle, installation hardware and caps. Din-en-iso 9001: 2000 quality standard manufactured, e-mark approved. The matching rear belt is part # FVD803993hr sold individually. 2 necessary per car.
$162.80
Make a selection FVD98661810MG Genuine: engine - 6 cylinder boxer capacity - 2480ccm compression ratio - 11,0:1 max. Power - 150kw (204hp) @ 6000rpm max. Torque - 245nm (181lbf ft) @ 4500rpm max. Speed - 240km/h max. Rpm - 6700rpm acceleration 0-100km/h - 6.9s tuning: max. Power - 158kw (215hp) @ 6000rpm max. Torque - 260nm (192lbf ft) @ 4500rpm max. Speed - 247km/h max. Rpm - 6900rpm acceleration 0-100km/h - 6.7s very important note: our tool can only flash ecu's with the Bosch # 0 261 204 605. If your ecu does not have this Bosch # then the ecu must be sent to us to be flashed in house. Please check the sticker on the outside of your ecu to determine which Bosch # you have. You can check by opening the rear trunk and pulling the carpet li...(choose a part on the right to read more)
$984.50
Make a selection FVDBS352964001 Make your next brake service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. This kit contains: 1 qty. Oem set of rear pads (4 total), part # 96535293904 2 qty. Oem brake warning sensors, part # 96461236502 4 qty. Oem brake pad damping shims (30 mm piston), part # 99635208600 4 qty. Oem brake pad damping shims (28 mm piston), part # 99635208602
$206.80
Make a selection FVDBS352965002 Make your next brake service a breeze with our pre-packaged service kits. Quality means everything to us, so we only source these parts directly in Germany. This kit contains: 1 qty. Oem set of rear pads (4 total), part # 96535293904 2 qty. Oem brake warning sensors, part # 96461236502 4 qty. Oem brake pad damping shims (34 mm piston), part # 96535209601 4 qty. Oem brake pad damping shims (30 mm piston), part # 99635208600 please note: this is for the European rs only, not for the rs america. This also fits both the 965 3.3l and 3.6l.
$174.90
Make a selection FVD504911RSR These fender flares are made of metal sheet set (4pcs): - fender flare front left - fender flare front right - fender flare rear left - fender flare rear right
$5,402.10
Make a selection 150PB100915 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 115993S1 Lowers the ride height by 30 mm (1.2 inches) in the front and 30 mm ( 1.2 inches) in the rear.
$663.30
Make a selection 11599700H Without pasm cars - lowers the front 1.2 inch (30 mm) and the rear 1.2 inch (30 mm). Pasm cars - lowers the front .8 inches (20 mm) and the rear .8 inches (20 mm).
$513.37
Make a selection 1588501000 Originally published by floyd clymer this is a faithful reproduction of the 1967 publication of that manual. Includes complete technical data, service and maintenance information and comprehensive detailed instructions for the repair and overhaul of all major and minor mechanical and electrical components. Covers the Porsche 356-356a-356b-356c series from 1948 through 1965, making it an invaluable resource for collectors and restorers of these classic automobiles. There are separate sections that deal with the repair and overhaul procedures for the engine, ignition system, fuel system, clutch, transmission, rear suspension, steering, front suspension, brakes, shocks, heater and exhaust plus a detailed electrica...(choose a part on the right to read more) General FitmentACCESSORY
$45.50
Make a selection 150PB100918 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 150PB1027 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's 911 models from 1978-89 if fitted with an 18mm original rear sway bar.
$49.50
Make a selection 115900993B12 If you're looking for the perfect combination of sporty dynamics, a superior appearance and high performance, you're on exactly the right track with this sport suspension. This kit is a direct replacement for the factory mo33 kit and will give you the same performance characteristics. -professional cornering system pcs -precise response, excellent driving performance and high reserves of safety -lowering up to 10 - 15 mm in front and rear -eibach pro-kit performance springs with progressive characteristic -springs and shock absorbers road-tested and fine-tuned to complement one other perfectly -bilstein gas pressure technology -bilstein mono-tube/upside-down technology, made in Germany -German TUV certificate...(choose a part on the right to read more)
$2,258.39
Make a selection 96410601402EQ This OEM cover sits low nearest the rear bumper. If you are removing the motor for maintenance, be sure to check and replace the engine covers / heat shields as necessary. We recommend purchasing a new seal, part # 96410622301 and plug, part # 96410623701 to complete the installation. Sold individually. 1 necessary per car.
$601.70
Make a selection 91163195200EQ Don't let a cracked or faded lens detract from your cars appearance. Replace it with this high-quality OEM replacement, designed to perform like the original. This was genuine equipment on usa models but really cleans up the rear when added in place of the amber look. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. Passenger's side fitment. 1 necessary per car. Loo...(choose a part on the right to read more)
$90.20
Make a selection 96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 96454303602 Necessary when replacing your right rear quarter window, as this seal retains the window in the body and prevents moisture from getting in. For 964 coupe models. Sold individually. 1 needed per car. Passenger's side fitment.
From $89.00
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 99905304104 High quality, European made, sealed angular contact bearing. This number is superseded from 999 053 041 01, 999 053 041 02 and 999 053 041 03. Sold individually. Left or right side fitment. Please note: this is the front bearing for the 964 / 965 / 993 and 996 models. It is the front and rear bearing for the 986 models. View/Change Diagram
From $42.00
Make a selection 93035204601EQ The zimmermann OEM brake disc combines high-quality cast materials, a vented and perforated braking surface and includes z-coating. Features: better wet braking performance by permanent expulsion of brake dust and water. Sporty look. Anti corrosion "z-coating" prevents rust. Noticeable improvement in braking performance. Countersunk holes double as wear indicator. Simple bolt on, modifications are not necessary. Made in Germany. Sold individually. 1 necessary per car. Rotors should always be changed in pairs; the rear left is part # 93035204501eq
$237.60
Make a selection BES99126090S Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, m&m use lightweight, motorsports grade, t 316 stainless steel and motorsports grade carbon. Features: inner 3.5" (90 mm) polished stainless-steel tip with FVD logo outer 3.9" (100 mm) matte carbon surround includes clamps for complete installation fills the factory cut outs perfectly can be adjusted for r...(choose a part on the right to read more)
$856.90
Make a selection BES99126010S Our exhaust products are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany who is no stranger to Porsche racing exhausts. Each is tested comprehensively for flow rate, thermal stress, resistance to cracking, and longevity. To further ensure quality, m&m use lightweight, motorsports grade, t 316 stainless steel material. Features: polished stainless steel double walled to dissipate heat so discoloration will take longer to appear / easier to polish out includes clamps for installation fits the factory cut outs in the bumper perfectly can be adjusted for...(choose a part on the right to read more)
$600.60
Make a selection BBI9974010001 Features
$1,895.00
Make a selection 99905906400 This is the rear differential tapered roller bearing that sits between the differential and the flange (closest to the flange). We recommend replacing this bearing with any differential rebuild. Sold individually. View/Change Diagram
From $48.50
Make a selection BK7032 Originally published by floyd clymer this is a faithful reproduction of the 1969 publication of that manual. By far the most comprehensive manual ever published for the 912 Porsche it includes complete technical data, service and maintenance information and comprehensive detailed instructions for the repair and overhaul of all major and minor mechanical and electrical components, making it an invaluable resource for collectors and restorers of these classic automobiles. There are separate sections that deal with the repair and overhaul procedures for the engine, ignition system, fuel system, clutch, transmission, rear suspension, steering, front suspension, brakes, heater, exhaust and emission control system pl...(choose a part on the right to read more) General FitmentACCESSORY
$39.95
Make a selection FVD205993001HAG These bushings are made for h&r rear sway bars with 24 mm diameters. They are a direct replacement for our part # FVD205993001. If you would also like to replace the front, please use part # FVD205993001vag sold as a front set. 1 set needed per car.
$58.30
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |