Vehicles
Sections
190 not categorized PORSCHE CAYMAN S BEARING SETCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: BOXSTER 1997-04 (includes uncategorized and accessory items)
$133.81
Make a selection 99654207504
View/Change Diagram
From $128.00
Make a selection 99333104503ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install the bushings. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part.
$254.10
Make a selection 99310314715SET Set of 12 standard size rod bearing shells. Sold as a set. 1 necessary per car.
$160.60
Make a selection 9A160410400EQ If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually, you will hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter, be sure to check the protection cap on the terminal for cracks which allows moisture in and causes pre-mature failure. High-quality denso OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$506.00
Make a selection 106085 Ims solution. Solid bearing replacement with oiling system. General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05
$1,756.89
Make a selection 930123002X This remanufactured turbo is a direct replacement for original part # 930 123 002 00. The remanufacturing is completed in Germany by kkk/borg warner certified technicians. This ensures reliability, superior performance and cost effectiveness. The remanufacturing process includes: complete disassembly. All parts are cleaned, inspected and measured for tolerances. Turbine wheels are replaced. Thrust bearings are replaced. All new seals are installed. Internals are reconditioned. Parts are balanced (static & dynamic) according to balancing protocol. For a complete installation we recommend adding a gasket, part # 93012319105 an intake sleeve, part # 93011015801 and be sure to have a few spare studs on hand, part #...(choose a part on the right to read more)
From $2,981.74
Make a selection 96434101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection 96434101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection 91511608705 On the flywheel side, the guide tube facilitates the movement of the thrust bearing in order to engage / disengage the clutch. On the gearbox side it provides a seal between the gearbox and driveshaft. These two functions are critical, so we recommend replacing the guide tube with any thrust bearing or clutch replacement. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
From $115.01
Make a selection FVD1109114840 This replica high butterfly mfi throttle bodies system is for those looking for ultimate engine performance as well as an authentic rsr engine appearance. This kit keeps air consistently on tap for superior drivability. When the throttle is opened, there is an instant injection of air, providing a sharp, crisp throttle response. This efficient injection frees up more power and compliments larger displacements, high lift cams and full exhaust systems. This kit is engineered, precision machined, flow tested and manufactured in Germany. It is replicated to look as close to the original as possible. Intake trumpets (velocity stacks) are available in your choice of red or black. Includes: 6 individual stacks (48 mm ...(choose a part on the right to read more)
$7,456.90
Make a selection 91110190100EQ Aftermarket complete set of bearings that does not include #8, sourced in Germany. Sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$148.50
Make a selection FVD1109115043 This replica high butterfly mfi throttle bodies system is for those looking for ultimate engine performance as well as an authentic rsr engine appearance. This kit keeps air consistently on tap for superior drivability. When the throttle is opened, there is an instant injection of air, providing a sharp, crisp throttle response. This efficient injection frees up more power and compliments larger displacements, high lift cams and full exhaust systems. This kit is engineered, precision machined, flow tested and manufactured in Germany. It is replicated to look as close to the original as possible. Intake trumpets (velocity stacks) are available in your choice of red or black. Includes: 6 individual stacks (50 mm ...(choose a part on the right to read more)
$7,456.90
Make a selection 269001354 Design must be functional - perfect symbiosis of comfort and design General FitmentALL
$1,058.94
Make a selection 269411351 Design must be functional - perfect symbiosis of comfort and design General FitmentALL
$1,376.94
Make a selection GR676 Because it resists heat flow, it adds years of life to your bearings and cv joints. Swepco has further improved this excellent grease by adding lubiuma tough film on all metal parts to protects them from extreme heat and pressure. 14 oz General FitmentALL
$16.50
Make a selection
$62.76
Make a selection
$1.10
Make a selection 99633377701 Known as: bearing clamp View/Change Diagram
From $9.50
Make a selection
$239.27
Make a selection
$236.39
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |