46 not categorized PORSCHE 930 MOUNTING PARTSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: BOXSTER 2005-08 - Transmission (includes uncategorized and accessory items) FVDBRO1016003A Weight savings approximately 4kg (8.8 lbs) of rotating unsprung weight. Oem disk weight 10,8kg (23.8 lbs), brembo disk weight 8.9kg (19.69 lbs) rotors: (13") 330x34mm drilled discs bells / hats: precision milled billet aluminum hardware: brembo floating anti-rattle disc hardware by using an aluminum bell for the hub section of the disc, these rotor assemblies save a great deal of weight. Since this is both rotating and unsprung, it benefits the acceleration, braking, and handling of the vehicle. Secondly, it is better able to handle the large temperature changes that a brake disc experiences. The mounting system is designed to allow a specific amount of float in both radial and axial directions. Brembo has eng...(choose a part on the right to read more)
$1,960.20
Make a selection 99635195930 A must for replacing your brake pads. This kit includes hardware to replace your old clips, backing plates (springs) and cotter pins. For two calipers. View/Change Diagram
From $41.90
Make a selection FVD10699701 This radiator is produced by the racing & high-performance division of csf who design, engineer and manufacture the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers all aluminum high performance radiators that are a direct-fit replacement for Porsche racecars and streetcars. Csf radiators improve cooling efficiency by 10-20 % over the factory radiators. Each radiator is stamped to the same geometry and includes aluminum end tanks that offer more reliability than the factory plastic end tanks. Each csf end tank features quality welding and is generally considered the strongest tank design in the industry. If you are planning to upgrade or replace your radiators, we highly re...(choose a part on the right to read more)
$592.81
Make a selection 99635195901 One required with each caliper. View/Change Diagram
From $25.61
Make a selection KEV503032011 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon fender that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 5.9 lbs. (2.68 kg) - made of high strength kevlar and carbon. - mounting is just like factory, no modifications are necessary. Please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world.
$1,312.74
Make a selection KEV503031011 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon fender that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 5.9 lbs. (2.68 kg) - made of high strength kevlar and carbon. - mounting is just like factory, no modifications are necessary. Please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world.
$1,312.74
Make a selection KEV53100501 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon door that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 4 kg (8.81 lbs) - kevlar / carbon - mounting is just like factory, no modifications are necessary. ** does not include the inner protection bar please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. Hinges are not provided; original hinges must be used. Please let us know the year and model and if you intend to use electric windows and electric...(choose a part on the right to read more)
$3,548.56
Make a selection HEI964001002S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: includes mounting plates that must be welded in. Chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Retains full seat adjustability. Semi-gloss black finish. Cost effective for club sport use. We r...(choose a part on the right to read more)
$741.31
Make a selection HEI911002001S1 We deliver with dmsb-ons certificat ,incl. Tunneling supporting and diagonal bars for the work location motorsport you need this options: 600001 side rotection 600035 dash board panel faces optional : 600036 harness mounting tube only in steel 600006 upholstery 600014 diagonals bars with connecting joint every heigo bar or cage is considered a motorsports part and is a special-order item. Motorsports parts may have some cosmetic inconsistency's (light scratches, etc.). For a perfect show car look, we suggest ordering the bar painted or powder coated.
$2,599.34
Make a selection 93020705304 Pmo parts is proud to introduce a euro style oil cooler to replace “trombone” style coolers used in most g-model cars.
From $495.72
Make a selection 91163193301EQ This is the inner headlight ring that retains the adjustment and securing screws. This part is "resi-coated" and includes all mounting hardware. Sold individually. Driver's and passenger's side fitment. 2 necessary per car.
$100.98
Make a selection 91150301605KEV Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar headlight bucket. Features: - produced by an OEM manufacturer. - lightweight .6 lbs. (.3 kg) - made of high strength kevlar. - metal mounting ring is cast inside the bucket for mounting. Sold individually. 1 necessary per car. Please note: requires drilling for wiring, etc. This is a high-quality part that takes time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world.
$836.35
Make a selection 846R9003 Material: tig welded, type 304, stainless steel. Finish: satin finish stainless. Weight: 6oz. Models: 996/997, Boxster, 911 & 944. Installation: secures snap-in lap belts to outside seat belt mounting point. Miscellaneous: allows user to remove and install belts in seconds. Will not interfere with factory seat belt. One pair will work for both seats. Use part 846r-9001 for inside belt mount.
$121.18
Make a selection 113LM099FD Genuine bbs motorsport center cap finished in gloss black with a silver logo. This cap is used primarily on the bbs rs, rx, rm and le mans type 099 wheel.
$23.76
Make a selection 91150301505KEV Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar headlight bucket. Features: - produced by an OEM manufacturer. - lightweight .6 lbs. (.3 kg) - made of high strength kevlar. - metal mounting ring is cast inside the bucket for mounting. Sold individually. 1 necessary per car. Please note: requires drilling for wiring, etc. This is a high-quality part that takes time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world.
$836.35
Make a selection 270503055 High-quality OEM front chin spoiler kit replacement that includes all necessary installation hardware. We source this part in Germany to ensure quality, reliability and precise fitment. Kit includes: qty. 1 front chin spoiler 930 / 911 wide body / turbo look 1975-89 - 93050305501 qty. 11 spoiler shim - 91150302300 qty. 1 left spoiler mounting plate qty. 1 right spoiler mounting plate qty. 15 m6 stainless nuts qty. 15 m6 washers sold individually. 1 needed per car.
$2,162.05
Make a selection 96437504381UNI The rs model engine mount is not a hydro-elastic mount like most models. It contains a rubber core with an 85-shore hardness value. That equates to a more responsive chassis and improved shifting response. A perfect compromise for street and track use as it is more forgiving than aftermarket solid mounts. Sold individually. 2 necessary per car. To install these mounts on any model 964 / 965 / 993 and 993 tt, we recommend our rs engine mount set that includes 2 mounts and all the mounting hardware, part # FVD375964
$236.41
Make a selection
From $59.40
Make a selection 98635293910 Note: for mounting parts use qty. One 996 352 959 01. View/Change Diagram
From $70.20
Make a selection 91163193300EQ This is the inner headlight ring that retains the adjustment and securing screws. This part is "resi-coated" and includes all mounting hardware. Sold individually. Driver's or passenger's side fitment. 2 necessary per car.
$100.98
Make a selection KEV53100600 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon door that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 6.4 kg (14.1 lbs) - kevlar / carbon - mounting is just like factory, no modifications are necessary. - includes inner protection bar please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. Hinges are not provided; original hinges must be used. Please let us know the year and model and if you intend to use electric windows and electric mirrors.
$3,751.70
Make a selection KEV53100500 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon door that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 6.4 kg (14.1 lbs) - kevlar / carbon - mounting is just like factory, no modifications are necessary. - includes inner protection bar please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. Hinges are not provided; original hinges must be used. Please let us know the year and model and if you intend to use electric windows and electric mirrors.
$3,751.70
Make a selection FVD51299101MM Make your 991.1 stand out with this subtle, yet stylish moshammer aero upgrade. The moshammer aero styling brand has become a leader in the premium automotive segment. Each part is precision designed and manufactured in Germany for perfect fitment and superior durability. Each part is tested and approved for added downforce to complement any performance upgrade. The moshammer rear diffusor from the "stormforce aerokit", is simple to install and reuses the factory mounting points on your OEM bumper cover. It is the perfect addition for a car that you are planning to turn in after a lease as the diffuser can be removed without any signs of it being installed.
$1,168.99
Make a selection FVD10699710 This radiator is produced by the racing & high-performance division of csf who design, engineer and manufacture the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers all aluminum high performance radiators that are a direct-fit replacement for Porsche racecars and streetcars. Csf radiators improve cooling efficiency by 10-20 % over the factory radiators. Each radiator is stamped to the same geometry and includes aluminum end tanks that offer more reliability than the factory plastic end tanks. Each csf end tank features quality welding and is generally considered the strongest tank design in the industry. If you are planning to upgrade or replace your radiators, we highly re...(choose a part on the right to read more)
$569.05
Make a selection BBI9818200001 Bbi autosport Porsche 981 Cayman GT4 streetcup roll bar features 4130 chrome moly steel tubing for excellent strength to weight ratio and addresses issues such as harness angle, seat travel, and engine compartment access. Taking a sensible design approach, the bar mounts to frame structure in the cabin and rear strut towers to provide the strongest mounting points and maximum protection. For superior strength and rigidity, high strength 4130 chrome moly steel tubing was used throughout and all joints are meticulously tig welded by hand. Bolt-in installation is accomplished by using inner diameter tube clamps that are cnc turned and milled for a precise fit. These unique joints eliminate the unsightly through-bo...(choose a part on the right to read more)
$2,586.60
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |