327 not categorized PORSCHE 924 GT ORDER FORMCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: BOXSTER 2009-11 - Uncategorized (includes uncategorized and accessory items) 115900997BIGT3D Bilstein b16 damptronic not only engine performance but, above all, suspension technology contributes to the fascination of a Porsche sports car. Bilstein offers an range of active coil over systems of the current Porsche models with pasm. The coil over system is electronically adjustable. So pasm-function and car sensors like psm stays fully in function. In addition the height-adjustment offers a certified range of lowering. Discreet sporty looks and precisely defined response within both setup modes, accompanied by high driving dynamics and excellent residual ride comfort. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it...(choose a part on the right to read more)
$5,330.60
Make a selection 150PB100922 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 96434101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 018 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 96434101707AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 017 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 91120127200EQ We suggest periodically checking your gas cap seal for fine cracks which produce fumes. If you replace the cap and the fumes persist, check the fuel filler neck, fuel lines, expansion tank and vent shut off valves. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$14.30
Make a selection 150PB100918 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 115900997BIT011 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 91120127200EQAS We suggest periodically checking your gas cap seal for fine cracks which produce fumes. If you replace the cap and the fumes persist, check the fuel filler neck, fuel lines, expansion tank and vent shut off valves. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$18.70
Make a selection 210111011D1 Improve sound and performance by decreasing exhaust backpressure with this catalytic bypass pipe. This is a painted steel bypass pipe, manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. - + 10 crank hp. - lower, deeper, more exotic exhaust note. - steel coated with high temperature paint. - made in europe by dansk. - reduces back pressure and thermal load on the engine. - includes o2 sensor bung....(choose a part on the right to read more)
$306.90
Make a selection 17021102103 This is a high-quality replacement heat exchanger manufactured by dansk. It is manufactured in steel and includes a corrosion resistant protective coating. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk930100 sold individually. Right or left side fitment. 2 necessary per car.
$837.10
Make a selection 150TBR900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the front of the control arm is part # 150tbf900 sold individually. 2 necessary per car.
$49.50
Make a selection 17092102S This cross over connector replaces original part # 930 111 157 01, it is a quality stainless steel replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For proper installation, we recommend a new exhaust gasket, part # 93011119307 and sealing ring, part # 91111118903 sold individually. 1 necessary per car.
$82.50
Make a selection 115900997BIT021 The pss 10 suspension kit provides the ultimate in performance tuning. The fully adjustable monotube gas shock absorbers offer a selection of nine precise compression and rebound settings. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Handling and control are just a few twists away. Regardless of whether in daily motoring, on the nordschleife of the nurburgring at the weekend, in training courses or in club sports - it's all pure driving enjoyment! Product advantages at a glance: • bilstein mono-tube/inverted technology • bilstein road tested and tuned • high driving dynamics with g...(choose a part on the right to read more)
$4,345.00
Make a selection 150BA7902 This bursch racing catalytic converter replacement pipe reduces engine damaging heat at the track and increases performance in the mid-range and top end. Like all bursch products, this replacement pipe is coated in high temp. Paint (1,200 degree). Use of this product for purposes other than solely for competition and off-road use is a violation of federal law and may violate applicable state or local environmental, motor vehicle and other laws. This product is intended for racing and off-road vehicles which may never be used on a public road
$93.50
Make a selection 150TB112801 High-performance, direct replacement torsion bar set that allow you to dial in the correct spring rate for street or track use. Features: lighter weight tubular / hollow torsion bar set manufactured from aircraft grade, 4340 alloy steel heat treated for increased strength and durability powder coated to resist corrosion consistent outside diameter and rate for consistent spring rate made in the usa by sway-a-way sold as a set. 1 necessary per axle.
$515.90
Make a selection 170211025SS This is a high-quality replacement for original number, 930 211 025 01 manufactured by dansk. It is manufactured in stainless steel. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911102 sold individually. Right or left side fitment. 2 necessary per car. Please note: this will not fit u.s. 3.0 l SC models from 1980-83. We suggest our part # 100 2...(choose a part on the right to read more)
$975.70
Make a selection 115333615B6 46mm monotube shock absorber setting: b6 heavy duty (hd) drive type: awd position: rear quantity per vehicle: 2 bilstein b6 heavy duty monotube gas pressure shocks and struts are the ideal choice for most vehicles, including full-size sedans, suvs and trucks. These shocks provide improved handling and stability, without sacrificing ride comfort. They offer super damping ability that makes them ideal for the driver who demands superior performance, while maintaining an exceptional street ride. (yellow paint, steel body)
$367.40
Make a selection 220110981001 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)
$1,479.50
Make a selection 240981351RSL2 Pagid yellow rsl 2 are from the rsl line of endurance racing brake pads. They are a medium high friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl 2 pads are based on the rsl 1 compound but are further improved in terms of pad and disc life and friction stability vs. Temperature. Rsl 2 maintain a constant friction level over a wide range of temperatures. Applications include: GT cars, touring cars, prototype endurance racing and in spring racing. Features at a glance: medium high friction coefficient medium high bite medium high fade resistance high pad and disc life high modulation pagid is one of the leading manufacturers of racing brake pads and is successful at t...(choose a part on the right to read more)
$793.10
Make a selection 22011098100 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)
$1,529.00
Make a selection 240911352HBH Pagid light blue rsh29e are from the rsh line of historic racing brake pads. They are a medium to high friction coefficient racing compound that requires less pedal effort during racing. Rsh29e pads provide constant friction levels over a wide range of operating temperatures. They offer lower disc wear rates and long pad life. Applications include: historic endurance racing, historic GT racing and historic touring car racing. Features at a glance: medium to high friction coefficient very good thermal stability low pedal effort slightly progressive in-stop behavior and good modulation long pad and disc life pagid is one of the leading manufacturers of racing brake pads and is successful at the world's most dema...(choose a part on the right to read more)
$251.90
Make a selection 220110997061 More air = more power! The incredible 997.2 Porsche turbo received a completely redesigned engine with many substantial upgrades. This latest turbo is the most powerful, revolutionary and capable Porsche turbo to ever come out of stuttgart. The 997.2 Porsche turbo may have been labeled a facelift but the engine is another major evolutionary leap forward in Porsche's coveted turbo history. This 7th generation turbo engine, titled the 9a1, delivers 500 hp (530 hp in s models) and once again, raises the performance bar in the sports car world. The new 997.2 ipd turbo plenum was considerably more difficult to design and develop than previous plenums. The good news is that all these efforts have yielded a much easi...(choose a part on the right to read more)
$1,094.50
Make a selection 240991352GRST1 Pagid red rst 1 are from the rst line of circuit racing / sprint racing brake pads. They are a high friction coefficient compound with high initial bite. Rst 1 pads have high temperature resistance, a progressive torque curve and are very fade resistant. They are a semi metallic resin bonded material containing steel and acrylic fibers. Rst 1 pads offer medium pad life and relatively high disc life with moderate modulation. They are suitable for heavy cars where high torque is necessary. Applications include: rally tarmac, GT cars, touring cars, nascar and high downforce formula cars. Features at a glance: very high friction coefficient high initial bite progressive torque curve very fade resistant medium modul...(choose a part on the right to read more)
$680.90
Make a selection 90157391500EQ Expansion valves regulate the flow of refrigerant. When they start to fail, they can create frost on the vents or the ac compressor, blow warm air or constantly run the ac compressor. High-quality hella OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$35.20
Make a selection 90142470106 High-quality OEM replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
From $28.60
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |