129 not categorized PORSCHE 930 A ARM BUSHINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: CAYENNE 2003-06 - Front Axle/Steering (includes uncategorized and accessory items) 96434307181ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$194.70
Make a selection 96434101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 018 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection FVD33300905ATK Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this does not fit cars with the g50 transmission.
$312.40
Make a selection 96434101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for...(choose a part on the right to read more)
$418.00
Make a selection 99333104503ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install the bushings. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part.
$254.10
Make a selection 99334101702ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install original control arm bushings. . Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can be made for its return to you. We do not offer a core exchange on this part. Sold individually....(choose a part on the right to read more)
$418.00
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 150PB10134 Replace worn-out original sway bar drop link bushings with this longer lasting poly-graphite plastic bushing set. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. The set includes 4 complete bushings and 4 sleeves (8mm inner diameter). Sold as a set. 1 necessary per car.
$73.70
Make a selection FVD10099902 With the roll bar camera mount and your video camera, you can have it all. 3-axis adjustment lets you capture any view - study strategies, document infractions, refine your technique, even tape yourself as you drive. Special vibration-absorbing urethane bushings assure a clear picture. No drilling required easy installation. Security strap included. General FitmentALL
From $157.94
Make a selection FVD33300905 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: made from ¼ inch spring steel includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car.
$273.90
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$451.96
Make a selection FVD33150040R Replace worn-out original rear sub frame (side panel) bushings with our FVD clubsport series. They are made of rubber with an 85 shore hardness value, that is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. We also sell the entire right and left rear sub frames with these bushings already installed, please order our part # FVD331993001.
$429.00
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection FVD33150003 Rear toe control arms - order in pairs only restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm can't compensate enough when lowering your Porsche, leaving you stuck with as much as ½ of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration.
$218.90
Make a selection FVD33150046R Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$66.00
Make a selection FVD205996003VAG These bushings are made for h&r front sway bars with 25 mm diameters. They are a direct replacement for our part # . These will also work on any bar with a 25-mm diameter. If you would also like to replace the rear, please use part # FVD205996003hag sold as a front set. 1 set needed per car.
$58.30
Make a selection FVD33391100SET Replace worn-out original spring plate bushings to return your car to its intended ride quality and performance. This is a high-quality OEM 65 shore density bushing set, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD34101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD33391101SET These bushings are manufactured from higher density, rs specification rubber (85 shore). Rs bushings are more durable than OEM 65 shore, provide more positive suspension location and are still quiet and compliant for street use. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD33150001 Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)
$243.10
Make a selection FVD33394401SET Replace worn-out original spring plate bushings to return your car to its intended ride quality and performance. This is a high-quality OEM 65 shore density bushing set, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. This set is a direct replacement for the rear axle strut bushings from original part # 477 511 201 and 477 511 202 sold as a set. 1 necessary per axle.
$108.90
Make a selection FVD37504332R Replace the worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushings. These are manufactured of rubber with an 85-shore hardness value. 85-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings. Rubber has a shore hardness value of 85 (like rs models) made in Germany sold as a set. 1 necessary per car.
$152.90
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection FVD34791130 Enhance steering precision and steering feedback by simply replacing your original tie rods. Turbo tie rods use a spherical inner joint instead of soft rubber bushings. They offer quicker steering response, more sensitivity and more precision. These are standard length we highly recommend them for lowered vehicles with bump steer kits like part # FVD34791100 or FVD347911930 . We also offer turbo tie rods in longer lengths for other applications, check part # FVD34791180r and FVD34791181ry this kit is manufactured in Germany by an OEM supplier, made from high carbon steel and 7075 t6 aluminum. Kit includes: 2 qty. Outer tie rods 2 qty. Inner tie rods 2 qty. Spacing washers 2 qty. Boots 2 qty. Castle nuts 2 qty. ...(choose a part on the right to read more)
$222.24
Make a selection 61610314202SET8
$73.70
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |