PORSCHE 987 LOW PRESSURE ACCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: CAYMAN 2006-08 - Engine (includes uncategorized and accessory items) 21011124OK Catalytic bypass pipe "u-torque" design, manufactured by m&m in Germany. The u-torque design compensates for the backpressure loss while running without cats. The design minimizes the loss of low end torque and adds 10-15 ft-lbs of torque in the mid and top range of the rpms. Why settle for the traditional cross over cat design when you can add torque in the mid-range and minimize the loss of torque down low where the 997's need it most! Ecu software is necessary !
$1,094.50
Make a selection 911606105DXATK The warm up regulator is a critical component that performs the following functions: lowers pressure when engine is cold. Absorbs / distributes engine heat. Allows for an additional rich mixture under full load to prevent engine damage. Altitude correction. Send us your original part and we will have it remanufactured for you. We do not offer a core exchange on this part. Each part is remanufactured in Germany, so the lead times can vary between 6-8 weeks. Sold individually. 1 necessary per car.
$744.70
Make a selection 47028608 Bmc sport air filters were originally developed in association with the ferrari f1 team. Bmc is one of the most recognized brands in the automotive industry and is the most successful filter in many types of racing. Oem filters only require a total particle filtration efficiency up to a minimum size of 10 microns. Oem air filters function primarily to protect the engine, so they are cost effectively produced in paper. Paper filters have high resistance to airflow that reduces the inlet pressure and consequently engine performance. A bmc sport filter contains an outer epoxy coated alloy mesh with internal layers of cotton gauze that have been immersed in a low viscosity oil. That technique ensures protection fro...(choose a part on the right to read more)
$122.10
Make a selection 47092620 Bmc sport air filters were originally developed in association with the ferrari f1 team. Bmc started producing their filters in 1973 and is one of the most recognized brands in the European automotive industry and is a member of the vdat German tuning association. Oem filters only require a total particle filtration efficiency up to a minimum size of 10 microns. Oem air filters function primarily to protect the engine, so they are cost effectively produced in paper. Paper filters have high resistance to airflow that reduces the inlet pressure and consequently engine performance. Bmc filtration systems yield more engine performance, both in terms of power and torque without compromising reliability. A bmc sport ...(choose a part on the right to read more)
$104.50
Make a selection 47090704 Bmc sport air filters were originally developed in association with the ferrari f1 team. Bmc is one of the most recognized brands in the automotive industry and is the most successful filter in many types of racing. Oem filters only require a total particle filtration efficiency up to a minimum size of 10 microns. Oem air filters function primarily to protect the engine, so they are cost effectively produced in paper. Paper filters have high resistance to airflow that reduces the inlet pressure and consequently engine performance. A bmc sport filter contains an outer epoxy coated alloy mesh with internal layers of cotton gauze that have been immersed in a low viscosity oil. That technique ensures protection fro...(choose a part on the right to read more)
$368.50
Make a selection 115384 If you are looking for added damping performance on the street, the bilstein b6 performance damper is the ideal solution. The product benefits at a glance: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Marked improvement in safety and sportiness without additional spring changes. Increased service life. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Road-tested and fine-tuned by bilstein. German TUV registration is not required. Sold individually. 1 necessary per car. We recommend adding our lowering spring collars if you would like a lower ride height, our part # 115110016
$640.20
Make a selection BES99125010SK Are you one of those that are looking for more sound from your Porsche sport exhaust (pse)? Perhaps it's not quite as aggressive as you would like, or your last Porsche just sounded so much better? Don't worry, we have you covered, and the beauty is, you don't have to touch the catalytic converters which is a big no, no with Porsche dealers. With the valves open you receive a far more exotic, rich, deep, turbo motorsport tone and with the valves closed, soft subtle, completely stock sounds. So, absolutely no compromise and you will be thinking, the car really should have left the factory like this! Features: - + 10 crank hp & + 8 crank torque. - weighs 29 lbs. (13 kg) - German v2a - x5crni18-10 - 1.4301 stai...(choose a part on the right to read more)
$4,312.00
Make a selection FVD123041ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection FVD3522P38056AS The brembo gran turismo s (gt-s) braking system is ideal for clubsport and sprint type track events. The GT-s type iii system utilizes brembo type iii aggressive face type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. Gt-s systems contain advanced calipers that include racing style radiators, dual inner piston seals, an inner pressure seal and an outer wiper seal. This innovative design provides the best combination of performance and long-lasting track use. The calipers are hard anodized in black (machined brembo logo in red) for resistance to corrosion and...(choose a part on the right to read more)
$4,174.50
Make a selection BES99125040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 25 hp & + 19 torque* - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes new clamps and muffler straps.* - made in Germany. - modular design for future 100 cell, 200 cell or cat bypass use. - more distinguished ...(choose a part on the right to read more)
$2,655.40
Make a selection BES99102240SHD + 15 hp & + 14 torque - 200 cell high flow, tri metal German hjs "hd" high durability matrix sports catalysts. - can be used with FVD "brombacher" mufflers. - weighs 15.5 lbs. (7.0 kg). - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - made in Germany. - intoxicating growl at idle, partial throttle and wide open throttle. The catalytic converter cores used in this system are the most advanced in the industry. They are produced by hjs in Germany and are a 200 cpsi (cell per square inch) tri-metal design. Tri-metal cats are the freest flowing and environmentally friendly aftermarket cats produced today. Tri-metal catalytic converters are rodium, platinum and iridium coated and per...(choose a part on the right to read more)
$3,293.40
Make a selection FVD1169013 Kit contains the following part: pressure plate, disc organic-torsion, release bearing, grease 260 nm
$1,264.82
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,544.10
Make a selection AP958170 Agency power is proud to release its super sport exhaust system for the 958 Porsche Cayenne s v8 2011 and up. the super sport exhaust is a axle system that gives your 4.8l v8 engine a real aggressive tone. made here in the usa, the exhaust saves close to 30lbs off the rear end of the vehicle. using 304 stainless steel and detail oriented tig welding, the exhaust system uses two small high flow mufflers which give it the sports car rumble. its reduced back pressure design gives the engine improved horsepower and torque with most noticeable improvement in throttle response. because of the reduced restriction, this exhaust horsepower gains can definitely be noticed in the mid to top rpm range.
$1,495.95
Make a selection BES99120040S Take your 991.1 or 991.2 turbo or turbo s to a new level with these muffler bypass pipes. They produce the wildest sound available on the market today and are a perfect upgrade for level 3 or 4 car used on the track. They produce loud, low, deep tones with exaggerated turbo whistling and sinister gurgling and crackling off throttle. By far the best sound you can get out of your turbo, not to mention being able to shoot flames! The only real drawback is the drone in the cabin which we try to minimalize by stepping down the diameter in 3 stages. Features: - + 35 crank hp & + 25 crank torque - 3 tubing (75mm) that tapers down to 2.25" (57mm) to prevent turbo damage. - weighs 7 lbs. (3,1 kg) - German v2a - x5crni1...(choose a part on the right to read more)
$672.10
Make a selection FVD33396400 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,708.92
Make a selection FVD12399600R Silicone boost hose kit FVD's direct replacement boost hose kit eliminates common boost hose "blow outs" on modified turbo's. Facts: tested to withstand over 75 psi (5 bar) boost pressure.fuel and oil resistanttemperature range between - 50 to + 180 degreesbolt on kit over time the OEM boost hoses tend to expand and contract under higher load, which leads to leaks, or "blow outs". Also, the OEM aluminum end does not secure properly into the intercooler, which causes boost leaks, and boost hose blowouts. Our machined billet ends are a perfect secure fit and our silicone hose is designed not to expand under boost pressure. The hose kit is a complete bolt on kit.
$590.70
Make a selection 115910996031 Bilstein b4 OEM m030 (original m030 suspension) shock absorber set (4 pieces) for cars with lowering springs or cars delivered with factory m030 sport suspension. Nothing is better than the original! The b4 m030 dampers from bilstein are the perfect shock absorber for lowered cars. Facts: - constant damping pressure under load - increased driving stability - increased durability - OEM quality - bilstein gas pressure technology - type/model m030
$1,682.59
Make a selection 911606105JXATK The cis injection / k-jetronic warm up regulator is a critical component that performs the following functions: lowers pressure when engine is cold. Absorbs / distributes engine heat. Allows for an additional rich mixture under full load to prevent engine damage. Altitude correction. Send us your original part and we will have it remanufactured for you. We do not offer a core exchange on this part. Each part is remanufactured in Germany, so the lead times can vary. Sold individually. 1 necessary per car. Please note: this part number encompasses: Bosch part 0 438 140 045 for 911 SC models from 1977-80 and Bosch part 0 438 140 089 for 911 SC models from 1980-83
$744.70
Make a selection RES9811000S Our entire "brombacher" line of exhausts is manufactured by m&m exhaust, gmbh in Germany. They manufacture a multitude of Porsche motorsport and racing exhausts. Each system is tested comprehensively for flow characteristics, thermal stress, cracking, and longevity. If you are looking for an exhaust product that can handle abuse at the track, look no further. Features: + 16 hp (12 kw) and + 11 tq (15 nm) long tube race headers with sprung motorsports merge collector German v2a - x5crni18-10 - 1.4301 (t304) lightweight stainless steel for improved durability catalytic bypass for race use primary diameter outer 50 mm into 63.5 mm motorsport collector reduces back pressure and thermal stress increased mid-range ...(choose a part on the right to read more)
$3,722.40
Make a selection FVD123013 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection FVD33396401 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,538.69
Make a selection FVD123014 K-16/24 turbo (up to 555 hp) power is focused on low and mid-range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD Brombacher993 k-16/24 new turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The process starts with re-profiling the OEM turbocharger compressor housing and m...(choose a part on the right to read more)
$2,976.60
Make a selection GR676 Because it resists heat flow, it adds years of life to your bearings and cv joints. Swepco has further improved this excellent grease by adding lubiuma tough film on all metal parts to protects them from extreme heat and pressure. 14 oz General FitmentALL
$16.50
Make a selection VDO150855 Vdo 1-150 psi nylon tubing kit, 16 foot. Includes 1/8-27 & 1/4-18 npt adapters. installation kit, oil pressure/vacuum, plastic tubing, 16 ft. Length, brass fittings, 1/8 in., 1/4 in. Npt,kit vdo tubing kits allow you to plumb your mechanical pressure gauges cleanly and easily. The kits include tubing, 1/8 in. -27 thread, and 1/4 in. -18 thread adapters. General FitmentALL
$24.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |