122 not categorized PORSCHE 924 GT CAT LIGHTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: PANAMERA 2010-14 - Engine (includes uncategorized and accessory items) 644631101072
$342.10
Make a selection 21011123 Catalytic bypass pipe "x torque" design made by m&m in Germany. The x torque design in is a true x pipe design. It is open in the center to add backpressure for torque. Give's you 10-15 ft-lbs of torque in the mid range along with 10-15 hp in the higher rpms. Why settle for the traditional cross over cat design when you can add torque in the mid range where the 996's need it most! Dme programming is necessary. Without it you will get a check engine light (cel). Tech tip: for older cars repair-kit FVD mk 996300
From $764.50
Make a selection 22011098100 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)
$1,529.00
Make a selection 24135296401BS Highlights: superb daily driver, OEM replacement, r90 type approved pad. Features red "brake in" surface coating for instant safe braking after install. New 100 % eco friendly material with zero sulphides. No shims for noise reduction needed. More bite from cold. Works in hot and dry climates as well as in cold. Fully r 90 approved. If you simply need a quality OEM replacement pad, look no further than the blackstuff brake pad. It is a highly engineered brake compound that lasts longer, produces minimal dust and is the perfect choice for the urban or daily driver. Why spend more if all you need is a quality replacement pad? The blackstuff brake pad is a total non metallic pad containing zero steel fiber, maki...(choose a part on the right to read more)
$123.20
Make a selection 150PR784 Porsche Cayenne s full bra features: two piece (2-pc) fog light opening with headlight washer/wiper opening with license plate opening (us) (euro license plate needs modification) with sensors
$148.50
Make a selection 240911352HBH Pagid light blue rsh29e are from the rsh line of historic racing brake pads. They are a medium to high friction coefficient racing compound that requires less pedal effort during racing. Rsh29e pads provide constant friction levels over a wide range of operating temperatures. They offer lower disc wear rates and long pad life. Applications include: historic endurance racing, historic GT racing and historic touring car racing. Features at a glance: medium to high friction coefficient very good thermal stability low pedal effort slightly progressive in-stop behavior and good modulation long pad and disc life pagid is one of the leading manufacturers of racing brake pads and is successful at the world's most dema...(choose a part on the right to read more)
$299.20
Make a selection 100555111890100 Since 1984, we have established an extensive network of interior specialty vendors that have stockpiled historically correct materials and have the skills necessary to reproduce to o.e. Specifications. Each carpet set is produced in Germany and includes every concours quality detail. For vehicles with rectangular brake fluid reservoir and without intensive headlight cleaning system. Features: historically correct perlon / felt material original fitment molded / form fitted includes correct cut outs includes correct button / snap holes and velcro manufactured in Germany sold as a set of 3 pieces. 1 necessary per car.
$378.40
Make a selection BES99110200SK1 "brombacher" stainless steel sound switch exhaust system complete for the 991 3,4l. + 25 hp & + 20 tq gain. - 200 cell hjs "hd" sport catalysts. - 25 lb. Weight savings over OEM system (weighs 59 lbs. (27,0 kg), OEM weighs 84 lbs. (38kg). - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - motorsport merge collector. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - "aero quip" style motorsport connections without gaskets or flanges to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. Please note: the 991 Carrera s (us or canadian model) comes standard with valves! Power...(choose a part on the right to read more)
$9,556.80
Make a selection BES99110200SK "brombacher" stainless steel exhaust system with valves for the 991 + 25 hp & + 20 tq gain. - 200 cell hjs "hd" sport catalysts. - 25 lb. Weight savings over OEM system (weighs 59 lbs. (27,0 kg), OEM weighs 84 lbs. (38kg). - 2 3/4 tubing (70mm). - 4 x 3.5 (90mm) round tips. - motorsport merge collector. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - "aero quip" style motorsport connections without gaskets or flanges to ensure a leak free exhaust. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - under load (moving) with valves closed: 85db* - under load (movin...(choose a part on the right to read more)
$10,030.90
Make a selection 100211025SSUSA If you have a us model 1980-83 911 SC and are looking to replace your heat exchangers we have some good and bad news. The original heat exchangers (part # 930 211 025 02) are no longer available from Porsche. But, these stainless-steel industries (ssi) heat exchangers will work with modifications. The good news is, once done, you will have more torque and horsepower! Free flow conversion heat exchangers improve sound and performance, while reducing backpressure and thermal load on the motor. These are based off the early style exhausts found on the 1974 2.7 l rs. Those models had a straight through, superior, free flow exhaust design that included a dual inlet muffler. When converting to these heat exchangers y...(choose a part on the right to read more)
$2,863.30
Make a selection 24135291101BS If you simply need a quality OEM replacement pad, look no further than the blackstuff brake pad. It is a highly engineered brake compound that lasts longer, produces minimal dust and is the perfect choice for the urban or daily driver. Why spend more if all you need is a quality replacement pad? The blackstuff brake pad is a total non metallic pad containing zero steel fiber, making this a cleaner pad which is far less aggressive to cast iron brake rotors. Blackstuff has also been graded code "n" by the usa brake ratings system meaning this receives the top award for its environmentally friendly status and has also achieved the much coveted gg friction rating, almost unheard of in the automotive brake industr...(choose a part on the right to read more)
$97.90
Make a selection BES99726000SO FVD is proud to introduce our newest line of Brombacherexhaust systems. Brombacher exhausts are engineered for the discerning Porsche owner and offer unmatched performance, unparalleled quality, and incredible value. All of our exhausts are manufactured in Germany and are tested comprehensively for flow rate and characteristics, thermal stress, resistance to cracking, and longevity. Brombacher mufflers outer shell dampens and eliminates unwanted frequencies and ensures no resonance or drone in the cabin. The end result is a strong, linear, firing-order dominated flat-6 Porsche sound. In addition, Brombacherexhausts systems are available for ultimate performance full titanium. Our titanium system's are nearly...(choose a part on the right to read more)
$1,359.60
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection KEV53100600 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon door that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 6.4 kg (14.1 lbs) - kevlar / carbon - mounting is just like factory, no modifications are necessary. - includes inner protection bar please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. Hinges are not provided; original hinges must be used. Please let us know the year and model and if you intend to use electric windows and electric mirrors.
$3,473.80
Make a selection KEV53100601 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon door that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 4 kg (8.81 lbs) - kevlar / carbon - mounting is just like factory, no modifications are necessary. ** does not include the inner protection bar please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. Hinges are not provided; original hinges must be used. Please let us know the year and model and if you intend to use electric windows and electric...(choose a part on the right to read more)
$3,285.70
Make a selection HEI993001003S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Semi-gloss black finish. Cost effective for club sport use. We recommend adding the harness bar, part # hei600036s to your order as it...(choose a part on the right to read more)
$1,188.00
Make a selection HEI911002001S2 We deliver with dmsb-ons certificate with wel-in parts, harness bar, tunneling supporting & diagonal bar optional : 600006 upholstery every heigo bar or cage is considered a motorsports part and is a special-order item. Motorsports parts may have some cosmetic inconsistency's (light scratches, etc.). For a perfect show car look, we suggest ordering the bar painted or powder coated.
$2,479.40
Make a selection HEI914002001S We deliver with dmsb-ons certificate. For competition motorsports you will need these options: 600044 every heigo bar or cage is considered a motorsports part and is a special-order item. Motorsports parts may have some cosmetic inconsistency's (light scratches, etc.). For a perfect show car look, we suggest ordering the bar painted or powder coated.
$2,625.70
Make a selection KEV53100501 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon door that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 4 kg (8.81 lbs) - kevlar / carbon - mounting is just like factory, no modifications are necessary. ** does not include the inner protection bar please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. Hinges are not provided; original hinges must be used. Please let us know the year and model and if you intend to use electric windows and electric...(choose a part on the right to read more)
$3,285.70
Make a selection KEV53100500 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon door that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 6.4 kg (14.1 lbs) - kevlar / carbon - mounting is just like factory, no modifications are necessary. - includes inner protection bar please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world. Hinges are not provided; original hinges must be used. Please let us know the year and model and if you intend to use electric windows and electric mirrors.
$3,473.80
Make a selection BES99105040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 15 hp & + 12 torque - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes cone and v band style hardware to prevent exhaust leaks. - made in Germany. - modular desi...(choose a part on the right to read more)
$2,920.50
Make a selection HEI911001008S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Tig welded. Semi-gloss black finish. Please note: these bars are hand made to order. They typically take between 4-16 weeks. Every heigo bar or cage is considered a motorsport part and is a special-order item. Moto...(choose a part on the right to read more)
$1,086.80
Make a selection KEV503032011 Made in europe by one of the manufacturers to Porsche. Extremely high-quality kevlar / carbon fender that includes every detail for a perfect fit. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight 5.9 lbs. (2.68 kg) - made of high strength kevlar and carbon. - mounting is just like factory, no modifications are necessary. Please note: these are high quality parts that take time to manufacture and cure properly. Lead times can vary anywhere from 15-30 days depending on where you are in the world.
$1,215.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |