Vehicles
129 not categorized PORSCHE 924 END PLATECan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.96433102100RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 96433113781 We recommend replacing these when installing new spring plates. Sold individually. 2 necessary per car.
From $31.90
Make a selection 96434350301 This is the lower strut plate that retains the spring and sits on top of the adjusting nut. We recommend that you inspect and replace if necessary with any new shock install. This plate tends to suffer from corrosion as debris collects in it with time. Sold individually. Right or left side fitment. 2 necessary per car.
From $39.00
Make a selection 99311691101 Eliminate your clutches slipping and chattering with this genuine kit. We only recommend this kit for non-modified cars that are not running any aftermarket upgrades like exhaust, chip tuning or larger displacements, etc. Complete kit consists of: 1 qty. Clutch disc 1 qty. Pressure plate 1 qty. Release bearing 1 qty. Spline lubricant kit weighs 14.1 lbs. (6.4 kg) tech tip: when you are planning to install a new clutch, it is a good idea to replace the clutch release fork and shaft to ensure proper clutch engagement, our part # FVD116999. We also recommend a new guide tube 95011681306 for proper installation. View/Change Diagram
From $768.04
Make a selection BES91105000S This muffler was specifically designed for a backdate to the st look. It is manufactured for mid-range and top end performance, all without drone inside the cabin. It seamlessly mates to ssi heat exchangers for added performance while keeping the cabin warm in the winter. The muffler is vastly different than the common baffle plated mufflers stuffed with packing material that are common in the aftermarket. Ours are uniquely made with double perforated sound absorption tubes based on the halbgegenstromprinzip (half counter current principle). The acoustic silencer absorption tubes are made in a trapezoidal pattern and are perforated with varying diameters, which isolate and dampen the unwanted frequencies that c...(choose a part on the right to read more)
$2,627.90
Make a selection AP997TT108 As you step up the power level on your 997 turbo, having proper cooling efficiency is mandatory to maximize your turbo performance. Street and track cars will heavily benefit from the use of our upgraded intercoolers. The factory Porsche intercooler core is great, but their end tanks are what is lacking. Agency power has developed these complete intercooler replacements for your Porsche 997 turbo. Some modifications are required to the intercooler frame and vehicle for fitment. General Fitment911 TURBO/GT2 2001-05
$1,749.95
Make a selection BES96405000S1 This muffler produces a glorious flat six race car with low deep tones that reminds us of the 964 cup. It is manufactured in Germany by m&m exhaust, gmbh. This muffler is ideal for anyone who wants a lower deeper tone with more decibels, whether they are just replacing the side muffler or are running cat bypass, sport cats or a cup pipe. + 14 hp (10 kw) & + 15 tq (20 nm) gain. - 2 3/4 tubing (70mm). - weighs 13.8 lbs (6.3 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions. - includes factory style hangars and new aero quip style clamps for simple installation. We recommend replacing your exhaust tip with this u...(choose a part on the right to read more)
$1,438.80
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,544.10
Make a selection BES98215000S2 The open architecture of this muffler allows for a deeper four-cylinder turbo tone, with plenty of whistling on tap. Coming off throttle from higher rpms exudes a chorus of snarling, gurgling and crackling letting everyone know that this car is not your average 982. + 15 hp & + 12 tq gain. - 2 x 3.5 (90 mm) round tips. - thermal insulation on piping to keep suspension components cool. Withstands up to 2,012 degrees fahrenheit (1,100 degrees celsius). - lower deeper tones than the factory exhaust with far more whistling and gurgling / crackling off throttle. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - no drone in the cabin. - "aero quip" style motorsport muffler connections t...(choose a part on the right to read more)
$2,816.00
Make a selection BES99105040S Perfect muffler for those looking for a more aggressive exhaust note without changing the factory catalytic converters. The added benefit is you can reuse your OEM catalytic converters for emissions purposes. + 15 hp & + 12 torque - reuses OEM cats, perfect for those concerned about warranty. - open muffler design for added power. - tubing diameter is the same as the OEM system. - weighs 19 lbs. (8,6 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - 4 on a scale of 1-10 in volume (1 being stock) below 3,000 rpms, 6 on a scale of 1-10 in volume under maximum load (3 being stock). - includes cone and v band style hardware to prevent exhaust leaks. - made in Germany. - modular desi...(choose a part on the right to read more)
$2,920.50
Make a selection BES99125020SK No need for Porsche sport exhaust (pse) envy with this muffler! This offers weight savings and a far more exotic sound than the pse, all without drone. It is the perfect compromise for you and your loved ones. Rich, deep, turbo motorsport tones with the valves open and soft subtle, completely stock sounds with them closed. Top of the line or range depending on the english and is the best choice for a daily driver. Features: - + 16 crank hp & + 15 crank torque. - weighs 37 lbs. (17 kg) - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - direct bolt on replacement for the factory center muffler. - includes necessary installation hardware. - reduces turbo lag, backpressure and thermal lo...(choose a part on the right to read more)
$4,651.90
Make a selection BES99300241S The ultimate stainless steel system for the street. Completely civilized while cruising and opens at higher rpms. Quieter than the street / clubsport versions. More low and mid-range torque. Larger primaries, larger collector, largest diameter tubing on the market. Made for mid-range and top end performance with the added beauty of 3.5" (90mm) dual exhaust tips! + 25 crank hp & +24 crank torque (on average). - 2.9 tubing (75 mm) at the widest point. Primaries are 2.5" (64mm). - 200 cell hjs "hf" trimetallic catalytic converters. - t 316 lightweight stainless steel for improved durability over t 304. - 3.5" (90 mm) dual oval, double walled polished tips included. - intoxicating growl at idle, partial thrott...(choose a part on the right to read more) General Fitment911 1994-98
From $10,723.61
Make a selection 20505HRFFD The clutch masters fx350 system uses the power plus i pressure plate with a steel back segmented kevlar disc. Sprung disks can be used with the OEM flywheel or aftermarket lightweight flywheels. This clutch is designed for the ultimate street enthusiast or weekend racer running a normally aspirated car equipped with cylinder head work and/or hotter cam(s), or with medium-boost turbo or super-charger, or up to 100hp no2. General FitmentBOXSTER 1997-04
$1,502.96
Make a selection DASRB2NS Das sport bolt-in roll bar Porsche 996/997 (w/o sunroof) 99+ General Fitment911 1998-05
$2,018.25
Make a selection DV001A021 Synchronic dv is the first, truly compact, zero-diaphragm, high-flow diverter valve with a blistering actuation time measured at 25 milliseconds. Mass air flow (maf) and speed density (map) applications can apply the new design in push or pull orientation with the ability to fully re-circulate or vent-to-atmosphere the valve's discharge. General Fitment911 TURBO/GT2 2001-05CAYENNE 2003-06
$577.06
Make a selection FPOR0655 Their newly designed mufflers are hand built with high quality materials to give you years of performance for your Porsche c2/4 and Porsche 3.6l turbo. All of their mufflers are constructed with t304 stainless steel with radiused end-plates, and gussetted joints for superior strength. General Fitment911 1989-94
$1,846.46
Make a selection FPOR0755 B&b mufflers Porsche 993 wide body c4s c2s 96-98 General Fitment911 1994-98
$1,723.55
Make a selection FPOR0855 B&b mufflers elliptical tips Porsche 996 c4s 02-04 General Fitment911 1998-05
$2,206.91
Make a selection FPOR6100 Their newly designed mufflers are hand built with high quality materials to give you years of performance for your Porsche c2/4. All of their mufflers are constructed with t304 stainless steel with radiused end-plates, and gussetted joints for superior strength. Twin inlet mufflers, designed specifically for b&b headers, have a special slip-joint absorbing expansion and contraction during times of severe heat. Special race and street applications for your Porsche c2/4 are available with your choice of tips styles. Billy boat performance exhaust has a deep commitment to build quality products. With over 3 generations of fabrication and racing experience going into the development of every part that b&b makes, al...(choose a part on the right to read more) General Fitment911 1989-94
$1,510.87
Make a selection FPOR0878 Billy boat performance exhaust high performance stainless steel exhaust components for the 2009 and up Porsche 997/997s will enhance the driving experience of your Porsche. The mufflers are designed to be used with the stock exhaust tips or you can get a more distinctive look with b&b_s quad round double wall tips. For a sportier note the design team at b&b also developed a set of primary muffler bypass pipes that will not only increase the sound they also give you added performance over the mufflers alone. New for 2010 the mufflers and pipes come standard in a satin finish while the optional tips are polished to a mirror like finish. All of these components have no effect on the factory warranty or emissions. ...(choose a part on the right to read more) General Fitment911 2009-12
$3,375.28
Make a selection FPOR0900 B&b headers Porsche Boxster 97-99 General FitmentBOXSTER 1997-04
$2,346.41
Make a selection FPOR0950 B&b muffler Porsche Boxster 97-99 General FitmentBOXSTER 1997-04
$2,064.68
Make a selection FPOR0960 B&b muffler Porsche Boxster 00-03 General FitmentBOXSTER 1997-04
$2,064.68
Make a selection FPOR1120 Billy boat's newly designed mufflers are hand built with high quality materials to give you years of performance for your Porsche c2/4 and Porsche 3.6l turbo. All of their mufflers are constructed with t304 stainless steel with radiused end-plates, and gussetted joints for superior strength. Twin inlet mufflers, designed specifically for b&b headers, have a special slip-joint absorbing expansion and contraction during times of severe heat. Special race and street applications for your Porsche c2/4 are available with your choice of tips styles. Billy boat performance exhaust has a deep commitment to build quality products. With over 3 generations of fabrication and racing experience going into the development o...(choose a part on the right to read more) General Fitment911 1989-94
$5,294.94
Make a selection FPOR1600 Their newly designed mufflers are hand built with high quality materials to give you years of performance for your Porsche c2/4 and Porsche 3.6l turbo. All of their mufflers are constructed with t304 stainless steel with radiused end-plates, and gussetted joints for superior strength. Twin inlet mufflers, designed specifically for b&b headers, have a special slip-joint absorbing expansion and contraction during times of severe heat. Special race and street applications for your Porsche c2/4 are available with your choice of tips styles. Billy boat performance exhaust has a deep commitment to build quality products. With over 3 generations of fabrication and racing experience going into the development of every ...(choose a part on the right to read more) General Fitment911 1989-94
$3,813.08
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |