Vehicles
Sections
130 not categorized PORSCHE 993 A ARM BUSHINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1965-69 (includes uncategorized and accessory items) 90133300309 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New OEM spec. (65 shore) rubber bushings are installed to make this a direct bolt on. Features: made from ¼ inch spring steel includes new OEM spec. (65 shore) rubber bushings made in Germany sold individually. Left or right-side fitment. 2 necessary per car. View/Change Diagram
From $306.90
Make a selection 90110313101 This bushing is located in the small end of the connecting rod on the wrist pin side. Be sure to inspect and replace when refreshing the motor as worn wrist pin bushings can create piston slap which is inefficient and can cause engine damage. Sold individually. 6 necessary per car. View/Change Diagram
From $7.07
Make a selection 150PB100919 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber, so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's genuine rear sway bars only.
$44.00
Make a selection 90134722303 The original rubber bushing is proven to be a weak link that can fail prematurely, allowing chassis geometry to be compromised. Symptoms include suspension movement during acceleration, braking and cornering. The powerflex street bushing is manufactured of a more dense rubber than the original. It is a 70 shore compound that is more resistant to load than standard rubber which provides better control of chassis geometry for street use. Features: improved road handling more precise and accurate alignment constant steering geometry increased tire life better steering feedback longer service life of suspension components less nvh (noise vibration hardness) than the race 95 shore bushing please note: we recommend t...(choose a part on the right to read more) View/Change Diagram
$31.90
Make a selection 96433102200RATK Unsure about installing a replacement bushing? Send us your trailing arm and we will properly recondition and install the bushing for you. The reconditioning process includes full inspection of your trailing arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our rear clubsport trailing arm bushings, part # FVD3310212291. Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. They offer rs style handling characteristics, superior durability and are still forgiving enough for street use. When reconditioning the trailing arms, we als...(choose a part on the right to read more)
$672.10
Make a selection 91142413900 Bushings should be first in line for replacement if you are experiencing sloppy shifts, grinding or missed shifts. We also recommend replacing the shift coupler bushings 150pb00741 when replacing the shift rod bushing or just replacing the coupler 91142402404 itself, which is far less labor intensive. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. View/Change Diagram
From $4.00
Make a selection 96437504381 Replace your worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushing. This is manufactured of rubber with a 75-shore hardness value. 75-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings rubber has a shore hardness value of 75 (like rs models) made in Germany this mount is a high-quality OEM (original equipment manufacturer) replacement part, designed to perform like t...(choose a part on the right to read more)
From $199.99
Make a selection 935FSUSP This light weight, bolt in kit replaces the factory front suspension arms, cross-member, and rubber bushings when converting to a coil over front suspension system. General Fitment911 1965-69911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89 914 1970-76
$1,850.00
Make a selection 96434101707AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 017 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 96434101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. This item is also available with race bearings (85 shore).article number FVD 341 018 07at the reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD3419991. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform y...(choose a part on the right to read more)
$418.00
Make a selection 96434307181ATK Looking for a more cost-effective solution than ordering a new link? Let us recondition your original drop link. The reconditioning process includes full inspection, disassembly, degreasing and media blasting. Once fully prepared, we properly install new bushings, finish with a corrosion proof coating and include a new lock nut. Please note: each link is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your link we will notify you as soon as we can. Arrangements can be made for its return to you. Sold individually. 1 necessary per car.
$194.70
Make a selection 150PB1027 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's 911 models from 1978-89 if fitted with an 18mm original rear sway bar.
$49.50
Make a selection 98656188100PRM Rubber bushing attaches to other end of convertible top push rod (part# 986 561 279 01-prm)
$5.50
Make a selection 99333105280 The bushings are made of rubber with an 85-shore hardness value, which is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Sold individually.
From $764.50
Make a selection 91110190160EQ Oem (original equipment manufacturer) complete set of bearings (including # 8) sourced in Germany to ensure quality, reliability and precise fitment. Set includes: 1 qty. Crankshaft main bushing sleeve - bushing viii - oversize +0.25mm 12 qty. Crankshaft main bearing shells ii-vii (half) - oversize +0.25mm 2 qty. Crankshaft main bearing shells i (half) - oversize +0.25mm sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$692.05
Make a selection 99737503303SP Transmission mount (exchange) with harder 85shore bushing. - reduces the movement of the transmission. - improved the handling characteristics during acceleration and curves note: model 996 Carrera only with tiptronic transmission. 500 km running-in period (light noises).
$313.50
Make a selection ER1T911SBF Quality and attention to detail make these sway bars the choice for serious performance. These elephant racing lightweight bars are hollow. They are half the weight of competing bars of equal stiffness. Bearing blocks, drop links, and sway bar arms are cnc machined from aircraft-quality 6061-t6 aluminum for its high strength/weight ratio. Fully adjustable front and rear drop links eliminate suspension preload. Oversized, precision teflon-lined rod-ends provide long life, smooth operation, and high-reliability. Adjustable drop-link arm connection design provides infinitely adjustable sway bar stiffness rate and makes it easy to fine-tune your car's handling for various track conditions and driving s...(choose a part on the right to read more) General Fitment911 1965-69911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73 914 1970-76
$619.99
Make a selection 99737503303LA Sport (85shore)bushing for transmission mount. - reduces the movement of the transmission. - improved the handling characteristics during acceleration and curves note: model 996 Carrera only with tiptronic transmission. 500 km running-in period (light noises).
$141.90
Make a selection FVD205993001HA H&r rear sway bar with a 24 mm diameter. 2-way adjustable. This is the rear sway bar from our kit, part # FVD205993001. Includes bushings. Sold individually. 1 needed per car.
$401.50
Make a selection ER2051500 High performance bushing replacement, no squeaks! Want to experience precision driving, faster lap times, improved road feel and feedback? These patented elephant racing polybronze suspension bearings set a new standard for performance, ride quality and ease-of -installation. Polybronze have a rigid bronze bearing core that does not deform. The polyurethane jacket absorbs mount irregularities while the bronze inner bearing remains true, providing a free-moving machined-fit that rides on a precision race. provided grease fittings make re-lubrication a breeze and a figure 8 groove keeps grease in place. The combination delivers zero squeaks and friction-free suspension movement. well suited to street or track, ...(choose a part on the right to read more) General Fitment911 1965-69912 1965-69 914 1970-76 911 1970-73 911 1974-77 930 1975-77 911 1978-83 911 1984-86 911 1987-89
$288.00
Make a selection FVD33150046 Replace worn-out original soft rubber track rod bushings with these OEM replacements. They are made of rubber that has a 65-shore hardness value, just like the oem. They will restore the original ride comfort and are more forgiving than the clubsport (85 shore rubber). This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$60.50
Make a selection FVD33150001 Solid bushings and mounts allow you to achieve exact suspension articulation which improves handling and stability on lowered / race prepared cars. The original soft rubber bushings can deform under track loads which allows the sub frame to shift and throw the camber and toe off. Solid bushings will not deform and will keep the camber and toe settings in line which equates to confidence in cornering and faster lap times. These are intended to replace the soft rubber bushings on the original rear sub frame (part #'s 993 331 051 00 & 993 331 052 00). They are made in Germany and are TUV approved. Sold as a set. 1 set is necessary per car. Please note: if you are also driving your car on the street, they will res...(choose a part on the right to read more)
$243.10
Make a selection FVD33104381 The tow link is the furthest rear control arm on the rear axle. It is responsible for the toe angle adjustment. The OEM control arm bushings are simply too soft for track events and the teflon monoball racing bushings are too far too hard and noisy for street cars. Our sport bushings are made of a denser rubber (85 shore opposed to OEM 65 shore), which means that they are suitable for street and track use. Equally as important is that they do not produce any noise like the teflon bushings. FVD sport control arm facts: - better handling and more responsive. - makes precision adjustments of the suspension easier. - does not produce noise. - shore a hardness value of 85 for durability and handling. - fit's like o...(choose a part on the right to read more)
$451.96
Make a selection FVD33150046R Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$66.00
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |