Vehicles
Sections
262 not categorized PORSCHE 964 EMSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 1989-94 (includes uncategorized and accessory items)
From $81.62
Make a selection 99310605180 Allows you to convert to one fan belt to run the fan and alternator like the factory rs versions. Oem part sourced in Germany to ensure quality, reliability and precise fitment. Once installed the alternator will run at the fan speed. That will lessen the inertial load and will add slightly more horsepower and acceleration. - includes fasteners (3 qty. M 6x35) - weighs .4 lbs ( .17 kg) please note: for 993 race car conversions or for cars without a/c we also recommend the corresponding crankshaft pulley, part # 99310205040 sold individually. 1 necessary per car.
From $152.90
Make a selection 190044900 Cabrios need 2 x FVD 512 321. Please order separate. General Fitment911 1994-98911 1989-94
$1,098.46
Make a selection BES96410000S Lieferumfang: General Fitment911 1989-94
From $6,320.60
Make a selection BES96400200T
$21,479.70
Make a selection BES96404000SK
$2,620.20
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection RES96410100S
$6,993.80
Make a selection FVD11196417 Complete race exhaust system for all 964 models. General Fitment911 1989-94
$2,842.44
Make a selection FVD375003 Are you experiencing vibrations in the cabin? The most likely cause is a worn transmission mount. Severely worn mounts translate to engine component wear and can even cause difficulty shifting. Our mount is manufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Be sure to swap yours out during your next service. Sold individually. Central fitment in transmission carrier 96437502301. 1 qty. Required. Tech tip: now is the time to replace the old hardware as well. Below is a list of what is needed for installation. 1 qty. Hex head bolt m10x100 90007429202 1 qty. Lock nut m10 49020001 2 qty. Washers 10.3x...(choose a part on the right to read more)
$165.00
Make a selection FVD641102105GOBR01 Check-engine light position top right. Like new
$63.80
Make a selection FVD424550KEV High quality polished carbon emergency brake handle. Great detail is taken to attempt to match the original weave size, color and polish. Whether you are adding carbon to the interior or matching existing pieces, this is high quality and is made in Germany so it is made to last, like the original. Sold individually. General Fitment911 1994-98911 1989-94
From $303.53
Make a selection FVD641102105WOBR01 Check-engine light position top right. Like new
$63.80
Make a selection G64641102103SIR01 Like new
$25.30
Make a selection G64641102104R01 Like new
$47.30
Make a selection RES96400000S1
$5,674.90
Make a selection RES96400100S1 More low and mid-range torque than our race system with cat bypass. Larger primaries, larger collector, largest diameter tubing on the market. Made for mid-range and top end performance with the added beauty of dual exhaust tips! + 25 hp & + 23 torque - 100 cell hjs tri-metallic race catalytics. -2 1/2 tubing (63.5mm) for max. Power across the rpm range.* -weighs 49 lbs. (22 kg). -German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - aeroquip cone style catalytic connection design to prevent exhaust leaks. -includes aeroquip quick release clamps. -made in Germany by m&m exhaust, gmbh. -dual round 3 exhaust tips -intoxicating flat 6 growl at idle, partial throttle and wide open throttle. P...(choose a part on the right to read more)
$7,772.60
Make a selection
From $238.27
Make a selection 10010303802 Perfect kit for street use, this is ultra-reliable, factory smooth kit will yield 35+ hp (depending on your additional modifications). These can also be used with OEM valves and camshafts. These are slip fit (107 spigot / 102 bore) and no modifications must be made to the case. Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resistance, they are nikasil coated which reduces wear and friction. We also have the piston rings (sealing and oil scrapers) pre-installed to ensure reliability. Each of our mahle piston and cylinder kits are complete and ready for installation. We also ...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $6,080.40
Make a selection 10010303804 The 11.8:1 compression will provide you with more acceleration than kits with 11.3:1 compression. For track use we recommend more aggressive cam (maximum valve lift (tdc) of 2.1 mm) . Piston's have very deep pockets for use with sport valves. These are 107 mm in size so are slip fit and do not require modifications. This kit is ideal for track use but can also be used on the street, it will add 40+ hp (depending on your additional modifications). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resistance, they are nikasil coated which reduces wear and friction. We also have ...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $6,080.40
Make a selection 10010303806 The 11.8:1 compression will provide you with more acceleration than kits with 11.3:1 compression. For track use we recommend more aggressive cam (maximum valve lift (tdc) of 2.1 mm) . Piston's has very deep pockets for use with sport valves. These are 107 mm in size so are slip fit and do not require modifications. This kit is ideal for track use but can also be used on the street, it will add 35+ hp (depending on your additional modifications). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resistance, they are nikasil coated which reduces wear and friction. We also have t...(choose a part on the right to read more)
$11,932.00
Make a selection 100105262 These camshafts are manufactured for the 964 and 993 rsr that use single throttle body intakes (rsr). Specifications: 5.0 mm at 0,00mm 320* bearing 49 mm not recommend for street cars! Please note: different manufacturing tolerances require an inspection of the free clearance of all parts! General Fitment911 1994-98911 1989-94
From $769.69
Make a selection 100105274 This camshaft is an excellent choice for those who spend time at clubsport track events or who race. These camshafts are manufactured in Germany by an elite German racing manufacturer, the quality and performance are top shelf. Timing inlet: 300* timing exhaust: 300* md: 112* lift inlet: 13.00 lift exhaust: 13.00 top dead center inlet: 3.00 top dead center exhaust: 2.90 weighs 6.3 lbs. (2.9 kg) please note: these will work on 964 models with upgraded pistons with larger valve pockets, changes to the camshafts are normally not necessary. For 993 models equipped with mechanical rocker arms, a groove must be inserted on the first journal. Please note: different manufacturing tolerances require an inspection of the...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $954.10
Make a selection 115900964BI01 Bilstein b16 (pss10) suspension kits feature ride height adjustability with 10-stage manually adjustable dampers. Simply adjust compression and rebound settings, from comfort to competition, by rotating the setting number knob at the base of the shock. The front and rear progressive rate springs allow accurate adjustment of the vehicle ride height and center of gravity for the level of performance you seek. Ride height is adjustable from 1.0 to -1.5 20-40mm (front) & -1.0 to -1.5 20-40mm (rear - minimum 1 lowering). Bilstein b16 (pss10) suspension allows you to enjoy the kind of precise suspension tuning formerly available only on race cars. We recommend purchasing our lowering collar kit if you plan to run the...(choose a part on the right to read more)
$3,855.50
Make a selection 10050330000 This 9 inch front and 11 inch rear steel fender flare set is made in Germany, we offer a complete line of replacement bodywork to complement the entire Porsche model range. Sold individually. 1 necessary per car. Please note: for conversions, these flares will allow you to run 9 wide tires in the front and 11 wide in the rear. For the 964 / 965 models the torsion bar cut out must be filled. Due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$1,648.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |