PORSCHE 930 SHAFT O RINGCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 2005-08 - Engine (includes uncategorized and accessory items) 93010501304 Genuine intermediate shaft and gear, sourced in Germany to ensure quality, reliability and precise fitment. We recommend ordering 6 qty. Oil pump lock plates part # 99903900100 for installation. Please note: please check the model fitment tab to ensure accurate fitment. Sold individually. 1 necessary per car.
From $1,612.60
Make a selection 93010501314 Genuine intermediate shaft and gear, sourced in Germany to ensure quality, reliability and precise fitment. We recommend ordering 6 qty. Oil pump lock plates part # 99903900100 for installation. Please note: please check the model fitment tab to ensure accurate fitment. Sold individually. 1 necessary per car.
From $1,661.00
Make a selection FVD10717601 This magnetic drain plug is cnc machined from 6061-t6 aluminum and has a large 3/8" rare-earth magnet to reduce iron (fe) levels in oil, which is a primary source for wear in your engine. The main reason to use a magnetic drain plug is the potential for ims (intermediate shaft) failures. The ferrous foreign object debris generated by a failing ims bearing will be caught by the magnet, allowing for earlier detection of critical engine problems before they happen! Torque to 37 ft/lb (50 nm) General Fitment911 2005-08911 1998-05 CAYMAN 2006-08 BOXSTER 2005-08 BOXSTER 1997-04
$28.33
Make a selection 99610590305 Known as: sealing ring for actuator camshaft / o-ring actuator camshaft / o-ring 18.72 x 2.62 View/Change Diagram
$14.97
Make a selection FVD10590109 Our tool is designed to replace the intermediate shaft bearing without engine disassembly. General Fitment911 2005-08911 1998-05 CAYMAN 2006-08 BOXSTER 2005-08 BOXSTER 1997-04
$214.50
Make a selection FVD20798701 This oil pump is a must for vehicles driven on the track. The issue: the 987.1 Boxster/Cayman from 2005 to 2008 has the factory return oil pump located on the right rear side. On the left side, the return oil pump located in front. So when driven fast in right turns, the oil from the camshaft case (rear left) does not flow back quickly enough into the oil pan. When the oil pan is starved of oil, the oil pump sucks in air and over time the motor will seize. The solution: our tandem return oil pump draws oil from the camshaft housing in (rear left, 3rd cylinder) and feeds it back into the oil pan so that starvation is not created when cornering hard.
$2,744.50
Make a selection 91511608705 On the flywheel side, the guide tube facilitates the movement of the thrust bearing in order to engage / disengage the clutch. On the gearbox side it provides a seal between the gearbox and driveshaft. These two functions are critical, so we recommend replacing the guide tube with any thrust bearing or clutch replacement. High-quality OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
From $115.01
Make a selection FVD123019ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD123042ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection P233944 Flywheel lock needed to stop the motor from rotating during r&r of crank shaft bolt or motor. Applicable: Porsche model - 944. Please call our office for availability.
$135.55
Make a selection FVD721T63 A metric dial gauge is a must for setting cam timing, measuring flywheel end play, crank shaft end play, etc. This is an extremely high quality, German ?käfer? Gauge whose design conforms to strict standards, and is made with accurate components and robust construction for reliability, durability and long working life. General FitmentALL
$88.00
Make a selection 93010734714 This part is sourced in Germany to ensure quality, reliability and precise fitment. This will fit all the vehicles listed in the fitment tab and those that have been updated to pressure fed tensioners. This line requires that you also purchase part # 93010734706 . We also recommend purchasing 1 qty. Union nut, part # 90010400303 and 1 qty. Cutting ring sleeve, part # n0208251 for installation. Also need the right side? Please order part # 93010734812 for the 911 3.2 l and 930 3.3l. Order part # 93010734815 for the 965 3.3 l. Sold individually. 1 necessary per car.
From $41.80
Make a selection 96410524707ST This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$1,410.20
Make a selection 96410524707GU This fits 964 c2 / c4 and rs models with engine codes # m64.01/02/03. This is an OEM part, sourced directly from Germany. Professional installation is required. Different manufacturing tolerances require an inspection of the free clearance of all parts! If you're not sure about what parts are right for your build, be sure to ask one of our parts specialists. Sold individually. 1 necessary per car.
$932.80
Make a selection 99911002500EQ Cylindrical roller bearing located on the top of the gear housing, nearest the housing. Sold individually. 1 necessary per car.
$124.30
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |