Vehicles
Sections
349 not categorized PORSCHE 914 DEL SOLCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 2009-12 (includes uncategorized and accessory items) 9A160410400EQ If your starter is on its way out, you will notice an intermittent clicking noise and a delay in the vehicle starting. Eventually, you will hear a metallic screeching noise that is a sure sign that your starters bendix mechanism, bearings or solenoid are kaput. When ordering a new starter, be sure to check the protection cap on the terminal for cracks which allows moisture in and causes pre-mature failure. High-quality denso OEM (original equipment manufacturer) replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car.
$506.00
Make a selection A143 Rennline rev4 fully adjustable gas pedal for left hand drive manual and tiptronic cars. Rennline's fully adjustable gas pedal system is an industry first, and finally solves the problem of the weak and unstable throttle assembly found on the late model water cooled cars. These factory plastic assemblies are notorious for hinge and housing failure due to its flimsy construction that was designed strictly for street use. The factory replaced these assembles on their race cars with a true metal to metal mount system, and now so can you. Rennline's fully adjustable pedal is a very unique system that gives you that true metal to metal mount, yet retains all your necessary electronics and or cables. Additionally, t...(choose a part on the right to read more) General FitmentCAYMAN 2006-08BOXSTER 2005-08 911 2009-12 PANAMERA 2010-14
$438.75
Make a selection BES95B05040SK + 15 hp & + 18 tq gain. - 2.5 tubing (63.5mm). - 4 x 4 (101mm) round tips. - 8.5 lb. Weight savings over OEM mufflers. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - electronic valve controller must be removed from the OEM unit and added to our muffler. - made in Germany. Please note: this muffler is a direct replacement the macan turbo (95b) model which comes with a single electronic exhaust valve on the passenger side. This is the very 1st aftermarket muffler for the macan 95b turbo that includes a valve like the factory system. This allows our system ...(choose a part on the right to read more)
$4,544.10
Make a selection 96434703200SP We are committed to Porsche cars and are very happy to release an outer tie rod that consists of a monoball joint. Until now this was something that was really only available on racing models. Our tie rod will provide you with unequalled steering precision for street and track use. This component is manufactured in europe and contains the finest materials available, high carbon steel and 7075 t6 aluminum. Installation is seamless, this is a direct replacement for the OEM number, 964 347 032 00. This is ideally suited for use with our monoball inner tie rod, part # 96434705805sp for the 964 c2 / turbo look or 965 or part # 96434705804sp for the 964 c4 or rs. Please note: this is not for the wide body. Sold indiv...(choose a part on the right to read more)
$322.21
Make a selection F8764121000294C Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to ensure that you select a high-quality product like your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night-time shading and include the original die cut notches for easy installation. Each set varies, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match interior or exterior color schemes. Don't see the color or combination that is right for your car? Or perhaps you want a custom logo in the tach? Kindly ...(choose a part on the right to read more)
$658.90
Make a selection FVD10699701 This radiator is produced by the racing & high-performance division of csf who design, engineer and manufacture the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers all aluminum high performance radiators that are a direct-fit replacement for Porsche racecars and streetcars. Csf radiators improve cooling efficiency by 10-20 % over the factory radiators. Each radiator is stamped to the same geometry and includes aluminum end tanks that offer more reliability than the factory plastic end tanks. Each csf end tank features quality welding and is generally considered the strongest tank design in the industry. If you are planning to upgrade or replace your radiators, we highly re...(choose a part on the right to read more)
$548.90
Make a selection BES99115000SKR + 11 hp & + 10 tq gain. - 2 3/4 tubing (70mm). - 18 lb. (8.5 kg)weight savings over OEM center muffler. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - absolutely no drone in the cabin. - does not interfere with emissions and will not trigger the check engine light. - ecu programming (software) is not necessary. - replaces OEM center muffler and connects to OEM header and OEM side mufflers and OEM tips. Please note: this muffler is a direct replacement the 991 Carrera s (3.8l - us model) which comes standard with valves. It is also a direct replacement for the Porsche sport exhaust option. This center muffler bypass for the 991 is one of the most technically advanced for Porsche t...(choose a part on the right to read more)
$3,713.60
Make a selection F8764121005TIP Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to ensure that you select a high-quality product like your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night-time shading and include the original die cut notches for easy installation. Each set varies, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match interior or exterior color schemes. Don't see the color or combination that is right for your car? Or perhaps you want a custom logo in the tach? Kindly ...(choose a part on the right to read more)
$603.90
Make a selection FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD11401214 Hailing from the baden wurttemberg region in Germany, speaking the language and dealing with lead engineers from the OEM and motor sport manufacturers for more than 30+ years has many advantages. We are able to source this flywheel from an elite German motorsports manufacturer who delivers the highest quality available. Features: quicker acceleration 9 bolt scalloped design precision machined billet steel computer balanced made in Germany replacement for original number 93010220201 sold individually. 1 necessary per car. Please note: this only fits 930 turbo models from 1978-79.
$526.90
Make a selection FVD50193600 Steel, prime coated floor pan repair panel made by dansk. They offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to European standards to ensure the quality that you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. 1 necessary per car. Please note: due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$341.00
Make a selection FVD10699702 This radiator is produced by the racing & high-performance division of csf who design, engineer and manufacture the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers all aluminum high performance radiators that are a direct-fit replacement for Porsche racecars and streetcars. Csf radiators improve cooling efficiency by 10-20 % over the factory radiators. Each radiator is stamped to the same geometry and includes aluminum end tanks that offer more reliability than the factory plastic end tanks. Each csf end tank features quality welding and is generally considered the strongest tank design in the industry. If you are planning to upgrade or replace your radiators, we highly re...(choose a part on the right to read more)
$548.90
Make a selection FVD123019ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection F8764121007TIP Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to ensure that you select a high-quality product like your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night-time shading and include the original die cut notches for easy installation. Each set varies, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match interior or exterior color schemes. Don't see the color or combination that is right for your car? Or perhaps you want a custom logo in the tach? Kindly ...(choose a part on the right to read more)
$603.90
Make a selection FVD34307101 Our direct replacement, OEM quality link uses rubber with a shore hardness value of 85. That is the same value as the rennsport models from Porsche. This link will offer superior performance under high cornering loads, more durability and are still forgiving for street use. Road noise not compromised with our links either. Facts: made in Germany. Crafted from high carbon steel and 7075 t6 aircraft aluminum. Weather sealed. Sold individually. Please note: we recommend buying these as a set, please purchase the right link, our part # FVD34307201
$93.50
Make a selection FVD362041002 High quality wheel nut and lock set. The set includes a key and teflon insert for your lug tool so the nuts will not be marred when removed. Please check the exact model designation for this part below. Sold as a set. 1 necessary per car.
$35.20
Make a selection FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$154.00
Make a selection FVD331993001 Our new rear sub frames contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. FVD clubsport sub frame facts: - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. - new sub frames with inserts installed. Sold as a set. 1 kit is necessary per car.
$1,758.90
Make a selection FVD375002 This mount kit is a solid upgrade like the European super cup cars. They will provide you with a more responsive chassis and faster lap times with a tighter feel to the car. Note: you will experience more vibration and more noise with solid mounts. Be sure to check the fits these models tab as these do not fit every model.
$87.99
Make a selection FVD361900715EU This fuchs replica is a classic design perfectly suited for any Porsche model. The center section is cast aluminum and finished black with a layer of clear coat. TUV approval documentation is standard with each wheel. The wheel accepts factory Porsche wheel bolts and center caps. Center caps sold separately, part # 190361035 or 190361033 sold individually.
$410.30
Make a selection FVD20799601 Scavenging and aeration in the oil pan have been identified as a problem in 996 and Boxster models experiencing high g-forces on the racetrack. This oil pan spacer provides a simple solution. This spacer increases sump capacity by half a liter, providing more reserve to ward off starvation. Thisoil pan spacer clears all factory options including the rear skid plate. Added oil capacities as well as increased oil pan surface area increase oil cooling and engine performance. *oil pan and sump baffle are OEM parts and do not need to be purchased material: 6061 t6 aluminum alloy finish: clear anodized weight: n/a models: Boxster, Boxster s, and 996 models (excludes GT3 and turbocharged models) installation: for best...(choose a part on the right to read more)
$283.80
Make a selection FVD34391192SET Replace worn-out original front lower control arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Features: better handling reduces that sloppy steering feel makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 2 necessary per car.
$158.40
Make a selection FVD361900815EU This fuchs replica is a classic design perfectly suited for any Porsche model. The center section is cast aluminum and finished black with a layer of clear coat. TUV approval documentation is standard with each wheel. The wheel accepts factory Porsche wheel bolts and center caps. Center caps sold separately, part # 190361035 or 190361033 sold individually.
$476.30
Make a selection FVD33150046R Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$66.00
Make a selection FVD51299122MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the evo rs (991.2 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: vented f...(choose a part on the right to read more)
$1,844.70
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |