77 not categorized PORSCHE 356 LIGHT KITSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 911 TURBO/GT2 2007-09 - Transmission (includes uncategorized and accessory items) 100555993RS This is a complete floor carpet kit for coupe models. This set is a lightweight fine German velour that is trimmed in vinyl. Each is cut, sewn and trimmed to fit perfectly. Drivers side vinyl heel pad and side pads (like original) is also included. Made in Germany. Sold individually.
$1,745.70
Make a selection 100555111NB This is a rear carpet kit for a rs model or a rs tribute, without back seats. This set is a lightweight fine German velour that is trimmed in vinyl. Each is cut, sewn and trimmed to fit perfectly. We can also add special order script on the rear deck, just contact us and let us know what you have in mind. Made in Germany. Sold as a set. 1 necessary per car.
$716.10
Make a selection 21011123 Catalytic bypass pipe "x torque" design made by m&m in Germany. The x torque design in is a true x pipe design. It is open in the center to add backpressure for torque. Give's you 10-15 ft-lbs of torque in the mid range along with 10-15 hp in the higher rpms. Why settle for the traditional cross over cat design when you can add torque in the mid range where the 996's need it most! Dme programming is necessary. Without it you will get a check engine light (cel). Tech tip: for older cars repair-kit FVD mk 996300
From $764.50
Make a selection 20934TD8SS It was only a matter of time before clutch masters built the ultimate clutch kit for the Porsche 996 and 997 turbo. With the success of their stage 3 OEM replacement kits holding 700 horsepower with daily driveability, clutch masters wanted to step up their clutch game and release this new 8.5 inch twin disk clutch with flywheel for the Porsche 911 turbo. This race version of the twin disk is recommended only for race use as initial pedal engagement as it requires finesse. The complete clutch weighs an astonishing 23lbs. The stock flywheel alone weighs about 40lbs! General Fitment911 TURBO/GT2 2001-05911 TURBO/GT2 2007-09
$6,156.00
Make a selection 220110981001 FVD Brombacherhas a long tradition of offering high quality, extensively tested, easily installed tuning products that offer proven performance. Those high standards naturally led us to the innovative pro design (ipd) plenum product. The ipd patented cast aluminum intake plenum with the larger 82 mm (gt3) throttle body (competition plenum) increases horsepower and torque by optimizing and increasing airflow into the intake manifold. But in order to capitalize on all the performance gains the ipd competition plenum can deliver, you must strike a balance with exhaust components and software. You cannot simply add the ipd competition plenum on the 981 series and expect large gains. But, no need to worry, the FVD ...(choose a part on the right to read more)
$1,479.50
Make a selection BBI9963010001 The bbi autosport Porsche 996/997 turbo clutch slave cylinder conversion kit is a direct replacement part that eliminates the problematic factory power-assist system for improved reliability and pedal feedback. The factory power-assisted clutch system has always been the achilles heel for the Porsche 997 turbo. Utilizing the power steering system to help reduce the force needed to depress the clutch pedal, it is a flawed design that delivers a mushy pedal feel with poor feedback, and is highly prone to failure.
$1,330.00
Make a selection 100555100RSSC This is a rear lightweight carpet kit for a rs model or a rs tribute, without back seats. This set is made from German lightweight felt and does not include floormats. Features: genuine German lightweight felt trimmed in vinyl made in Germany custom made to order manufactured in Germany sold as a rear set. 1 necessary per car. Please note: when placing your order, we require the year, model and a list of any interior upgrades like roll bars, etc. This kit is custom made to order.
$940.50
Make a selection 99704400007 Smooth-fitting outdoor car cover featuring full-color Porsche logo. Waterrepellent fabric protects your Porsche from weather extremes such as strong sunlight. Equipped with an anti-theft protection system. Suitable for the 997 turbo. Not suitable for vehicles with aerokit. General FitmentACCESSORY
$479.16
Make a selection 20934HD0F The perfect clutch for aggressive drivers that still desire smooth engagement like the OEM unit. Clutch masters stage 2.5 (formally known as the "stage 3") clutches utilize a full face disk made from clutch masters "fiber tough" material which is strong like kevlar but less abrasive on the flywheel. The pressure plate side is an organic disc to ensure a strong grip to hold your high horsepower Porsche. This will provide more holding power than stage 1, yet it still offers exceptionally smooth driveability and long life. The kit can be used with the factory flywheel without doing a break in or resurfacing or you can upgrade to a light weight flywheel for great turbo spool and throttle response. General Fitment911 GT3 2003-05911 TURBO/GT2 2001-05 911 GT3 2007-11 911 TURBO/GT2 2007-09
$2,505.33
Make a selection FVD3511M19004A The brembo gran turismo (gt) braking system is ideal for use on the street and for light track use. This GT system expands upon the original drilled disc's face type made by Porsche. The cross drilled disc surface continuously refreshes the braking surface and offers the highest initial response of any disc type. So, you can confidently respond to sudden pedestrian or traffic movement with maximum braking performance. Drilled discs operate in a wide range of operating temperatures and environments and respond confidently in wet weather. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with op...(choose a part on the right to read more)
$5,054.50
Make a selection FVD3511M18002A The brembo gran turismo (gt) braking system is ideal for use on the street and for light track use. This GT system expands upon the original drilled disc's face type made by Porsche. The cross drilled disc surface continuously refreshes the braking surface and offers the highest initial response of any disc type. So, you can confidently respond to sudden pedestrian or traffic movement with maximum braking performance. Drilled discs operate in a wide range of operating temperatures and environments and respond confidently in wet weather. The GT line is dedicated to the most demanding customers. It originates from racing components, consisting of floating ventilated cross drilled discs, aluminum calipers with op...(choose a part on the right to read more)
$4,394.50
Make a selection FVD1169901 Our FVD exclusive line of clutch kits is culmination of Porsche genuine parts, zf sachs race engineering gmbh parts and motorsports parts that have been developed to work together without compromise. The kit includes a disc with a rigid hub and organic friction material. It has superior thermal resistance, is more resistant to higher rpm's than the oe discs, offers greater longevity and can transmit higher torque (583 ft/lbs. / 790 nm max.). Please note that this kit has an aggressive start performance (release window is very small), we do not recommend this kit for lightly modified or stock street cars. Clutch kit includes: 1 qty. Clutch disc 1 qty. Pressure plate 1 qty. Release bearing 1 qty. Spline lubrican...(choose a part on the right to read more) General Fitment911 TURBO/GT2 2007-09911 TURBO/GT2 2001-05 911 1994-98
From $1,819.45
Make a selection FVD123019ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD33396400 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,708.92
Make a selection FVD33396401 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Slightly lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,538.69
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$2,976.60
Make a selection FVD3522P29024A Brembo's brake systems are designed to meet the the needs of the most demanding of customers. Brembo brake systems originate from racing components and offer proven on-track performance. Brembo high performance systems offer a significant reducuction in usprung weight for better handling and provides maximum braking force without the flex of sliding callipers. Brembo components reduce heat-related stress and increase brake performance for a better overall pedal feel with less fade. Brake kits come with aggressive pads that last longer than OEM and provide the highest level of performance. Brembo brake systems also consist of a ventilated, integral or composite brake disc, light weight aluminium calipers, steel...(choose a part on the right to read more)
$4,174.50
Make a selection FVD3522P29027A Brembo's brake systems are designed to meet the the needs of the most demanding of customers. Brembo brake systems originate from racing components and offer proven on-track performance. Brembo high performance systems offer a significant reducuction in usprung weight for better handling and provides maximum braking force without the flex of sliding callipers. Brembo components reduce heat-related stress and increase brake performance for a better overall pedal feel with less fade. Brake kits come with aggressive pads that last longer than OEM and provide the highest level of performance. Brembo brake systems also consist of a ventilated, integral or composite brake disc, light weight aluminium calipers, steel...(choose a part on the right to read more)
$4,174.50
Make a selection FVD50599108MM The moshammer stormforce evo rs front chin spoiler for the GTS model blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce and uplift reduction. It also incorporates twin air guides to assist with brake ventilation and underbody air flow efficiency. The moshammer stormforce evo rs front chin spoiler design offers exclusive aesthetics, aero functionality and it is secured seamlessly into the factory locations without modification. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the s...(choose a part on the right to read more)
$1,230.90
Make a selection FVD123014ATK K-16/24 turbo (up to 555hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbocharg...(choose a part on the right to read more)
$2,976.60
Make a selection FVD50399101MM The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)
$3,631.10
Make a selection FVD631997FLE Our led daytime running light upgrade kit transforms your 997.1 turbo (2006-2009) into exactly the same day time running feature as 997.2 turbo. Daytime running lights apply a powerful highlight to your Porsche and also contribute an active safety feature. The led's will be bright during the day and will dim when the headlights are switched on. Our kit includes electronic module (voltage converter), cables and OEM led daytime driving lights from the 997.2 turbo. - ece approved
$2,124.10
Make a selection 802026 Hella is one of the top names in automotive lighting and electrical systems, since 1899. Hella produces lighting systems for many European OEM applications, as well as aftermarket performance lighting systems. Each of their light kits feature high-performance bulbs, quality-made lamp housings and mounts, precision-engineered reflectors and optics, and detailed installation instructions. The 550 high-performance fog lamp is made of high-impact abs plastic. It can be mounted upright or pendant. Each 550 kit contains (2) halogen lamps, (2) 12v 55 watt halogen bulbs, (1) prewired color-coded wire harness with 12v fused relay and illuminated rocker switch and (2) stone shields. Pre-fitted cables make installation ea...(choose a part on the right to read more) General FitmentALL
$135.00
Make a selection PLE54109900SEGR Trying to save weight at the track? These makrolon polycarbonate race windows are very lightweight, strong and durable. They are made in Germany. Includes right and left rear quarter windows and the rear windshield. Does not include the seals.
$2,087.80
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |