PORSCHE 930 EFFCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 912 1965-69 - Front Axle/Steering (includes uncategorized and accessory items) 910165 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment911 1974-77911 1978-83 911 1984-86 911 1987-89 930 1975-77 911 1970-73 911 1965-69 912 1965-69 914 1970-76
$458.05
Make a selection MAP09029518 Endorsed by the Porsche museum, this comprehensive work features stunning photography and commentary from the personalities that have helped to make Porsche the iconic brand it is today the book rests in a high-quality protective slip cover and is a must-have for any Porsche enthusiast
From $132.00
Make a selection NLA10704100 Our aluminum oil cooler will give you these benefits:
From $605.00
Make a selection SB6090B One of the easiest and most cost-effective ways to improve your car's handling is the installation of a rennline strut tower brace. These braces bridge both shock towers, eliminating virtually all camber change that occurs during hard cornering. Not all cars are the same, so rennline has made their braces fully adjustable, allowing you to set a desired amount of pre-stress. Constructed of lightweight aircraft grade aluminum with stainless steel brackets. Rennline strut tower braces bolt in and out in minutes and require no drilling. Whether you're on the street or on the track you'll feel the difference immediately. Black in color, silver shown. General Fitment911 1965-69912 1965-69 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$195.00
Make a selection SB6090 One of the easiest and most cost-effective ways to improve your car's handling is the installation of a rennline strut tower brace. These braces bridge both shock towers, eliminating virtually all camber change that occurs during hard cornering. Not all cars are the same, so rennline has made their braces fully adjustable, allowing you to set a desired amount of pre-stress. Constructed of lightweight aircraft grade aluminum with stainless steel brackets. Rennline strut tower braces bolt in and out in minutes and require no drilling. Whether you're on the street or on the track you'll feel the difference immediately. Silver in color. General Fitment911 1965-69912 1965-69 911 1987-89 911 1984-86 911 1978-83 930 1975-77 911 1974-77 911 1970-73
$180.00
Make a selection FVD50599102MM The moshammer evo 2 front chin spoiler blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce. Porsche active aerodynamics remains fully functional in all 3 positions and the evo 2 chin spoiler secures seamlessly into the factory locations. The evo 2 spoiler's design offers a more aggressive look but also blends perfectly with other design elements like the side skirts and rear spoiler. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of either the evo rs (991.2 turbo/s) or downforce rs...(choose a part on the right to read more)
$1,386.00
Make a selection FVD50499101MM The moshammer side inlet set is a striking design that enhances performance and efficiency. The inlets create a ram air effect by scooping in a larger volume of air, which delivers up to 10% more air pressure into the intercoolers. These sets are available in satin black, gloss black or high gloss carbon. This is another versatile moshammer offering for a leased vehicle or for those looking to return the car to its original appearance in the future. This set complements the entire moshammer downforce rs (991.1 turbo/s) or evo rs (991.2 turbo/s) aero packages and benefits the mighty GT2 rs as well. Features: striking design increased performance added efficiency direct bolt on available in satin black, gloss bla...(choose a part on the right to read more)
$1,082.40
Make a selection FVD51299102MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the downforce rs (991.1 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: ve...(choose a part on the right to read more)
$1,460.80
Make a selection FVD50599106MM The moshammer front bumper upper air vent is a combination of aggressive styling, aero-efficiency and increased cooling capacity. It is a motorsport finishing touch that complements the entire evo rs (991.2 turbo/s) / stormforce (991.1) / stormforce evo rs (991.2) or downforce rs (991.1 turbo/s) aero packages. FVD Brombacherhas a tradition of offering exclusive body styling that is functional, easily installed, wind tunnel tested, German made and TUV approved. Those high standards naturally led us to the moshammer brand. The moshammer aero styling brand has become a leader in the premium automotive segment. Each part is precision designed and manufactured in Germany for perfect fitment, superior durability and...(choose a part on the right to read more)
$371.80
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD50599109MM The moshammer stormforce evo rs front chin spoiler for the c2 / c2s / c4 / c4s and the t models blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce and uplift reduction. It also incorporates twin air guides to assist with brake ventilation and underbody air flow efficiency. The moshammer stormforce evo rs front chin spoiler design offers exclusive aesthetics, aero functionality and it is secured seamlessly into the factory locations without modification. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added...(choose a part on the right to read more)
$1,237.50
Make a selection FVD505991ZFLA Our cost effective GT3 rs 4.0 style front bumper dive planes provide additional downforce and give your Porsche a more aggressive appearance. Installation is simple .
$655.60
Make a selection FVD51299122MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the evo rs (991.2 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: vented f...(choose a part on the right to read more)
$1,844.70
Make a selection FVD123041ATK FVD Brombacher997.1 tt "700 series" upgraded turbos facts: - cnc re-profiled compressor housing and backing plate - new, lightened and larger compressor wheel (12 blades) - reworked turbine wheel, lightened and optimized for higher flow and reduced backpressure. - all new bearings. - all new piston rings and seals. - all parts cleaned, inspected and measured to motorsport specifications. - all parts are balanced (static & dynamic) up to 120.000 rpm with balancing protocol. - 47.55 mm inducer - 66 mm exducer - flow rate = 37 lbs. / minute or 280g/s - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already runn...(choose a part on the right to read more)
$2,854.50
Make a selection 24135191101YS High efficiency performance and race brakes for track and street use, fast to bed-in, great for street vehicle brake upgrade. Not only a high friction pad but very resistant to heat and loads of heavy braking means that yellowstuff has been used with great success in race cars and on street cars. Yellowstuff is an aramid fibre based brake compound with high brake effect form cold and is possibly one of the first ever compounds that can be used for street and tack driving. These pads do not require warm up but do get even stronger under the heat of hard driving. These are not a low dust pad and if your desire is for a low dust premium street use pad, you should consider ebc redstuff. Highlights: made for up to 9...(choose a part on the right to read more)
$199.10
Make a selection 240991352RSL1 Pagid yellow rsl1 are from the rsl line of endurance racing brake pads. They are a high friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl1 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and have good friction stability vs. Temperature. Applications include: GT cars, touring cars, prototype racing and in spring racing. Features at a glance: high friction coefficient high bite high fade resistance high pad and disc life high modulation pagid is one of the leading manufacturers of racing brake pads and is successful at the world's most demanding racetracks. They offe...(choose a part on the right to read more)
$743.60
Make a selection 240991352GS Pagid yellow rsl 29 are from the rsl line of endurance racing brake pads. They are a medium friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl 29 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and offer excellent release characteristics. Rsl29 pads offer low heat conductivity and work well with abs systems. They offer excellent modulation and controllability. They offer lower disc wear rates and are fade resistant up to a temperature of 650*c (1,202*f). Applications include: club racing, track days, touring cars, prototype endurance racing and GT cars. Features at a...(choose a part on the right to read more)
$654.50
Make a selection 240996352RSL1 Pagid yellow rsl1 are from the rsl line of endurance racing brake pads. They are a high friction coefficient racing compound with long pad and disc life, and are easily bedded in. Rsl1 pads are manufactured of a low metallic resin bonded material containing steel and acrylic fibers. They operate in a wide operating temperature range and have good friction stability vs. Temperature. Applications include: GT cars, touring cars, prototype racing and in spring racing. Features at a glance: high friction coefficient high bite high fade resistance high pad and disc life high modulation pagid is one of the leading manufacturers of racing brake pads and is successful at the world's most demanding racetracks. They offe...(choose a part on the right to read more)
$512.60
Make a selection 91179950515EQ Don't let a worn, faded bellows detract from your cars exterior. Replace it with this replacement part for original number, 911 799 505 15. This is made by dansk, they offer a complete line of aftermarket replacement bodywork to complement the entire Porsche model range. All dansk aftermarket products are manufactured with quality and cost effectiveness in mind. Sold individually. 1 necessary per car. Driver's side fitment (lhd).
$33.00
Make a selection FVD3522P38056AS The brembo gran turismo s (gt-s) braking system is ideal for clubsport and sprint type track events. The GT-s type iii system utilizes brembo type iii aggressive face type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. Gt-s systems contain advanced calipers that include racing style radiators, dual inner piston seals, an inner pressure seal and an outer wiper seal. This innovative design provides the best combination of performance and long-lasting track use. The calipers are hard anodized in black (machined brembo logo in red) for resistance to corrosion and...(choose a part on the right to read more)
$4,174.50
Make a selection FVD50399101MM The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)
$3,631.10
Make a selection FVD50599108MM The moshammer stormforce evo rs front chin spoiler for the GTS model blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce and uplift reduction. It also incorporates twin air guides to assist with brake ventilation and underbody air flow efficiency. The moshammer stormforce evo rs front chin spoiler design offers exclusive aesthetics, aero functionality and it is secured seamlessly into the factory locations without modification. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the s...(choose a part on the right to read more)
$1,230.90
Make a selection FVD351425426EQ A quality, cost effective set of replacement "big red" style calipers. These are a direct replacement for the 965 turbo, 993 c4s / rs and 993 turbo but can be installed on many 964 / 993 models with the correct caliper adapters. Please contact your FVD parts specialist for fitment questions. We also recommend swapping out your brake lines for a set of stainless braided lines when replacing calipers. Also a now is the time to install a set of our speed bleeders, part # FVD910102. They are comparable to part numbers 993 351 425 10 and 993 351 426 10. Please note: these are aftermarket calipers and do not come with the logo or brake pads. Sold individually. 1 necessary per car.
$874.50
Make a selection FVD123048 FVD Brombacher997.2 tt "700 series" upgraded turbos facts: - modified compressor housing for the 3.8 l displacement - modified & lightened billet compressor wheel with 12 blades - 49.55 mm inducer - 68 mm exducer - remanufactured by borg warner certified technicians - shaft tolerances are strictly maintained to ensure durability - free software update for those already running FVD software we start by re-profiling the OEM vtg turbocharger compressor housing and modifying the compressor backing plate. This is done to replace the factory compressor wheel with a larger 12 blade, modified compressor wheel. The larger wheel is also lightened allows the turbo to flow a larger volume of air (more power), and aids i...(choose a part on the right to read more)
$6,413.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |