Vehicles
Sections
349 not categorized PORSCHE 930 DEL SOLCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 914 1970-76 (includes uncategorized and accessory items) FVD105911930 This kit contains everything needed for a valve adjustment. High-quality victor reinz gaskets with hardware, designed to perform like the original. We source this kit in Germany to ensure quality, reliability and precise fitment. Set includes: 2 qty. Lower valve cover gaskets 93010519507 2 qty. Upper valve cover gaskets 93010519404 2 qty. Oil strainer / sump plate gaskets 93010139101 2 qty. Sealing rings 90012311830 8 qty. M6 nuts 8 qty. Chain case washers 34 qty. Valve cover nuts 34 qty. Valve cover washers sold as a set. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.
$71.18
Make a selection FVD123019ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD201911964993 Looking to update your fuel cap? This is a cost effective, sporty, aluminum alternative to the factory cap. It resembles the tequipment cap available on the water-cooled models. It is a quality tuning product manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Oem non-locking, screw type fuel cap sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary ...(choose a part on the right to read more) General FitmentACCESSORY
$136.40
Make a selection FVD331993001 Our new rear sub frames contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. FVD clubsport sub frame facts: - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. - new sub frames with inserts installed. Sold as a set. 1 kit is necessary per car.
$1,758.90
Make a selection FVD211343 Already replaced your heater blower tube with a carbon bypass? This carbon / kevlar air duct will match the engine decor perfectly. It is a replica of the factory rs lightweight factory air duct. This is a quality tuning product manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. This installs easily and really dresses up the engine. Sold individually. 1 necessary per car.
$267.30
Make a selection FVD33105900 Replace worn-out rear trailing arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This is a direct replacement for original part # 90133105900 features: better handling makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 1 necessary per car.
$154.00
Make a selection FVD33399300 A cost effective FVD exclusive combination of bilstein clubsport shocks with a set of TUV certified eibach springs. This suspension kit will lower the front axle to a maximum of 35 mm (1.37 inches) and the rear axle to 30 mm (1.18 inches), like the European rennsport model. The height is adjustable as the dampers are threaded. They are a cost effective solution for clubsport use and will be well mannered on the street. Sold as a complete kit. 1 kit is necessary per car.
$11,872.30
Make a selection FVD34101800R Replace worn-out original strut mount bushings with our German made rs density set. Each is manufactured of a high-density rubber with an 85-shore hardness value. 85-shore is the same density used in rs models. This set is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This bushing is made in Germany by an OEM manufacturer. It is crafted of a high carbon steel insert with an 85-shore hardness value rubber surround. Sold as a set. 1 necessary per car. General Fitment914 1970-76911 1970-73
From $166.01
Make a selection FVD34307101 Our direct replacement, OEM quality link uses rubber with a shore hardness value of 85. That is the same value as the rennsport models from Porsche. This link will offer superior performance under high cornering loads, more durability and are still forgiving for street use. Road noise not compromised with our links either. Facts: made in Germany. Crafted from high carbon steel and 7075 t6 aircraft aluminum. Weather sealed. Sold individually. Please note: we recommend buying these as a set, please purchase the right link, our part # FVD34307201
$93.50
Make a selection FVD34307201 Our direct replacement, OEM quality link uses rubber with a shore hardness value of 85. That is the same value as the rennsport models from Porsche. This link will offer superior performance under high cornering loads, more durability and are still forgiving for street use. Road noise not compromised with our links either. Facts: made in Germany. Crafted from high carbon steel and 7075 t6 aircraft aluminum. Weather sealed. Sold individually. Please note: we recommend buying these as a set, please purchase the left link, our part # FVD34307101
$93.50
Make a selection FVD361900815EU This fuchs replica is a classic design perfectly suited for any Porsche model. The center section is cast aluminum and finished black with a layer of clear coat. TUV approval documentation is standard with each wheel. The wheel accepts factory Porsche wheel bolts and center caps. Center caps sold separately, part # 190361035 or 190361033 sold individually.
$476.30
Make a selection FVD362041002 High quality wheel nut and lock set. The set includes a key and teflon insert for your lug tool so the nuts will not be marred when removed. Please check the exact model designation for this part below. Sold as a set. 1 necessary per car.
$35.20
Make a selection FVD375002 This mount kit is a solid upgrade like the European super cup cars. They will provide you with a more responsive chassis and faster lap times with a tighter feel to the car. Note: you will experience more vibration and more noise with solid mounts. Be sure to check the fits these models tab as these do not fit every model.
$87.99
Make a selection FVD50193500 Steel, prime coated floor pan repair panel made by dansk. They offer a complete line of replacement bodywork to complement the entire Porsche model range. All dansk products are manufactured to European standards to ensure the quality that you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold individually. 1 necessary per car. Please note: due to variances in production at the factory, age, accident damage or rust, each part may require trimming and or adjustment for perfect fitment.
$316.80
Make a selection FVD50399101MM The moshammer front fender set blends just the right amount of motorsport pedigree with functionality. This aggressive design is captivating on any 991 model and offers a level of exclusivity not found with competitors body kits. The integrated fender vents lower the thermal load on the brakes by allowing the heat to be quickly ventilated up and out of the wheel arch. This composite fender set has been meticulously designed to bolt up to the factory locations for perfect panel fitment, alignment and consistent gaps. A perfect addition for a leased vehicle or for those looking to return the car to its original appearance in the future. These fenders complement the entire moshammer stormforce (991.1) / stormforce...(choose a part on the right to read more)
$3,631.10
Make a selection FVD50501901 When installing a lightweight bumper or bumper bar for racing use, you want to remove as much weight as possible. Don't forget to remove your heavy factory supports. This is a lightweight aluminum alternative, made in Germany. Weighs: 140 grams / .13 kilograms / .3 lbs. Sold individually. Please note: please check the model fitment tab to ensure accurate fitment.
$141.90
Make a selection FVD50599106MM The moshammer front bumper upper air vent is a combination of aggressive styling, aero-efficiency and increased cooling capacity. It is a motorsport finishing touch that complements the entire evo rs (991.2 turbo/s) / stormforce (991.1) / stormforce evo rs (991.2) or downforce rs (991.1 turbo/s) aero packages. FVD Brombacherhas a tradition of offering exclusive body styling that is functional, easily installed, wind tunnel tested, German made and TUV approved. Those high standards naturally led us to the moshammer brand. The moshammer aero styling brand has become a leader in the premium automotive segment. Each part is precision designed and manufactured in Germany for perfect fitment, superior durability and...(choose a part on the right to read more)
$371.80
Make a selection FVD50599109MM The moshammer stormforce evo rs front chin spoiler for the c2 / c2s / c4 / c4s and the t models blends a bit of Porsche heritage into its design with canard style winglets. This effective design transforms turbulent air into a more laminar flow, creating added downforce and uplift reduction. It also incorporates twin air guides to assist with brake ventilation and underbody air flow efficiency. The moshammer stormforce evo rs front chin spoiler design offers exclusive aesthetics, aero functionality and it is secured seamlessly into the factory locations without modification. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added...(choose a part on the right to read more)
$1,237.50
Make a selection FVD51299102MM The moshammer vented rear diffuser with fins is an aggressive design that reduces aerodynamic drag. This vented diffuser allows air that is trapped by the rear bumper to exit, allowing for greater top end performance. The design also incorporates 5 fins that improve laminar airflow by reducing turbulence. Moshammer manufactured this as a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looking to return the car to its original appearance in the future. When added to other elements of the downforce rs (991.1 turbo/s) package, the result is a confident, cohesive stance with balanced downforce. Features: ve...(choose a part on the right to read more)
$1,460.80
Make a selection FVD51299124MM The moshammer stormforce evo rs rear spoiler for the 991.2 model blends a bit of Porsche ducktail heritage into its design to increase rear downforce and reduce front axle uplift. The contours of this spoiler have a step effect which seamlessly blends into both rear quarter panels. When viewed at a standstill it has a subtle factory like appeal that complements the cars lines. When deployed the rake angle takes on a more aggressive appearance evoking thoughts of the much beloved ducktails. Like a majority of the moshammer offerings, this spoiler is a direct replacement, so it secures seamlessly to the factory locations with the original hardware. This is an ideal addition for a leased vehicle or for those looki...(choose a part on the right to read more)
$1,455.30
Make a selection FVD631403US Update or complete the look of your car with a set of clear turn signal lenses. These replace the original amber lens, part # 91163191400 and include us dual filament bulbs. We recommend replacing the rear lenses as well to the red / clear lenses, part # 91163195100eq and 91163195200eq . Quality tuning product manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Sold as a set. Passenger's and driver's ...(choose a part on the right to read more)
$128.69
Make a selection FVD72269500LGW This simple FVD Brombachertow hook installs in seconds and folds down to eliminate protrusion from the car's bodywork. It fits all Porsche's with factory left hand thread, screw-type tow hooks. It has a two-inch towing eye, which is required for track events. It is precision cnc machined stainless steel, tig-welded, has a polished shaft and a rubber locking rod to prevent loosening. Features: stainless steel light weight: 1.6 lbs. Fits any Porsche listed in our fits these models tab. Installs in seconds, simply remove the bumper plug and screw into the tow hook hole. Made in Germany. Includes FVD Brombacherlogo. Sold individually.
$137.50
Make a selection FVD890930183 We recommend changing your ignition cables when changing your plugs and distributor. Overlooking the ignition cables can lead to increased resistance and weak spark which causes incomplete combustion in the cylinder and robs your engine of power and efficiency. These cables are high-quality OEM (original equipment manufacturer) beru replacement, designed to perform like the original. We like that they incorporate secure wire ends with a brass receptacle and steel click spring. They also include correct OEM style protection sleeves and wire clips. We source these in Germany to ensure quality, reliability and precise fitment. Sold as a complete set. Please note: please check the model fitment tab to ensure accura...(choose a part on the right to read more)
$350.90
Make a selection FVD911503185186 This seal kit consists of original part # 911 503 185 00 (left) and 911 503 186 00 (right). The set can be used on the trailing edge of the front fender at the cowl just below the windshield. It is also used under the back of the rear quarter panel where it meets the bumper side panel. Genuine part sourced from Porsche ag in Germany to ensure quality, reliability and precise fitment. Sold as a set. 1 set is necessary for front fenders and one set is necessary for the rear. Please note: this is the thinner width. This is not the thicker width from the SC models.
$14.93
Make a selection RES98720000SS Having to weld up cracks regularly on your current aftermarket racing exhaust? If you are looking for a racing exhaust that can handle abuse at the track, look no further. This exhaust system is manufactured by m&m exhaust, gmbh in Germany. They manufacture a multitude of Porsche motorsport and racing exhausts. Each system is designed for reliability and performance gains throughout the entire rev range. Not to mention, you directly benefit from everything m&m learns at the track, so their systems designs are never static. Also, each system is tested comprehensively for flow characteristics / rate, thermal stress, cracking, and longevity. Features: + 20 hp & + 19 tq catalytic bypass pipes weighs 55 lbs. (23 kg)...(choose a part on the right to read more)
$5,082.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |