Vehicles
Sections
117 not categorized PORSCHE 944S BUILDCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 924 1976-79 (includes uncategorized and accessory items) 99312301452ATK Our k-16 remanufactured turbo is cost competitive and is a direct replacement. Simply send us your original k16 turbochargers and a borg warner / kkk certified technician will remanufacture your turbo. The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will replace the turbine wheels, thrust bearings, install new seals, recondition the internals and high speed balance the turbo. This ensures reliability and superior performance for many years to come. The remanufacturing is done on an exchange basis only. You must send us your original k16 turbocharger. After receiving y...(choose a part on the right to read more)
$2,194.50
Make a selection BL924 Over the years, deposits form inside your rubber brake lines, creating a hard brake pedal and sticky calipers. The permanent cure is to install a set of our stainless brake lines. They are teflon-lined to prevent mineral build-up and braided stainless steel to reduce line flex! (sold in sets of four.) excellent brake hose for racing. General Fitment924 1976-79924 1980-85
$75.59
Make a selection 99905902702 This is the differential output shaft bearing that attaches to the differential housing. We recommend replacing this bearing with any differential rebuild. Sold individually. View/Change Diagram
From $29.46
Make a selection FVD123019ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD10699711 For 996 turbo/gt2 and 997 GT2/gt3. - specially designed for tuned and motorsport vehicles the racing & high performance division of csf build and engineer the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers radiators with high performance all-aluminum and direct-fit replacement for racecars. The only high performance manufacture to feature this advanced technology. These radiators are stamped to the same geometry of the application's original plastic end radiators. These tanks feature less welding, and are generally considered the strongest tank designs in the industry.
$548.90
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$2,976.60
Make a selection FVD201911RSR110 Whether you are restoring a tribute car or endurance racing your 911, this tank will fit the bill. It is made in Germany from pvc plastic and includes high grade threaded brass inserts. It is build by fia specs and can be adapted to work in all 911's from 67-89. It holds a capacity of 29 gallons or 110 liters.
$3,065.70
Make a selection FVD123020ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD10699704 For 996 turbo and 997 turbo, 996 GT3l. Fits right side. - specially designed for tuned and motorsport vehicles the racing & high performance division of csf build and engineer the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers radiators with high performance all-aluminum and direct-fit replacement for racecars. The only high performance manufacture to feature this advanced technology. These radiators are stamped to the same geometry of the application's original plastic end radiators. These tanks feature less welding, and are generally considered the strongest tank designs in the industry.
$768.90
Make a selection FVD123014ATK K-16/24 turbo (up to 555hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbocharg...(choose a part on the right to read more)
$2,976.60
Make a selection 99310090238EQ FVD cylinder head gasket sets contain high quality German sourced gaskets, seals and o-rings. This kit contains a complete set of gaskets to make a teardown / rebuild more convenient. Sold as a complete set. 1 necessary per car. To complete the gasket set for the whole engine order please 93010090104eq too.
$614.58
Make a selection HEI993001005A Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar aluminum 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Aluminum finish. Primarily for street use as a harness bar is not an option. Please note: these bars are hand made to order. They typically take between...(choose a part on the right to read more)
$1,401.40
Make a selection FVD95761891MG Genuine: engine - v8 capacity - 4806 ccm compression ratio - 12,5:1 max. Power - 298kw (405hp) @ 6500rpm max. Torque - 500nm @ 3500rpm max. Speed - 253km/h max. Rpm - 7000rpm acceleration 0-100km/h - 6,1s tuning: max. Power - 312kw (425hp) @ 6000rpm max. Torque - 520nm @ 4500rpm max. Speed - 265km/h max. Rpm - 7200rpm acceleration 0-100km/h - 5,7s for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, making substantial gains in horsepower and torque, while retaining drivability and most importan...(choose a part on the right to read more)
$1,094.50
Make a selection FVD98010002 Kit includes: 2 x sport motronic dme (ecu) exchange 2 x sport airfilter 1 x sport exhaust system genuine: engine - v10 cylinder capacity - 5733ccm compression ratio - 12,0:1 max. Power - 450kw (612hp) @ 8000rpm max. Torque - 590nm @ 5750rpm max. Speed - 330km/h max. Rpm - 8400rpm acceleration 0-100km/h - 3.9s tuning: max. Power - 496kw (675hp) @ 8000rpm max. Torque - 670nm (495 lbf ft) @ 6000rpm max. Speed - 345km/h max. Rpm - 8600rpm acceleration 0-100km/h - 3.7s FVD dme / ecu programming philosophy: for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. ...(choose a part on the right to read more)
$17,032.10
Make a selection FVD95761890MG Factory: engine - v8 twin-turbo capacity - 4806ccm compression ratio - 10,5:1 max. Power - 368kw (500hp) @ 6000rpm max. Torque - 700nm (516 lbf ft) @ 2250-4500rpm max. Speed - 275km/h max. Rpm - 6500rpm acceleration 0-100km/h - 5.1s tuning:* max. Power - 397kw (540hp) @ 6000rpm max. Torque - 780nm (575 lbf ft) @ 3500rpm max. Speed - 280km/h max. Rpm - 6700rpm acceleration 0-100km/h - 5.0s * only with sport exhaust system and sport air filter for 27 + years, FVD-Brombacherhas been setting the standard for Porsche engine building and tuning in Germany. Our deep understanding of the flat 6 Porsche engine naturally led to our engine management software. Over the years we have perfected the art of software tuning, ...(choose a part on the right to read more)
$1,094.50
Make a selection HEI993001009A Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar only weighs 22 lbs (10 kg) aluminum 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Aluminum finish. Primarily for street use as a harness bar is not an option. Please note: these bars are hand made to order. ...(choose a part on the right to read more)
$1,760.00
Make a selection HEI964001009S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar - screwed in to the original seat belt points. Aluminum 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Black paint finish. We recommend adding the harness bar, part # hei600036s to your order as it is sold al...(choose a part on the right to read more)
$1,604.90
Make a selection GR2019 Professional assembly paste is now available to the masses. The first few minutes of initial operation after rebuild are the most important of your engine’s life. Lm 48 is a must for engine assembly. Apply to all bearing surfaces, cams, rockers, rod and main bearings. Protects against galling and damage to bearing surfaces due to the initial dry running. General FitmentACCESSORY
$17.15
Make a selection HEI911001008S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Tig welded. Semi-gloss black finish. Please note: these bars are hand made to order. They typically take between 4-16 weeks. Every heigo bar or cage is considered a motorsport part and is a special-order item. Moto...(choose a part on the right to read more)
$1,086.80
Make a selection HEI911001003S Heigo motorsports has been building extremely safe roll cages and roll bars for the Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. We purchase their bars because they have a long-standing history with the fia and dmsb in Germany. They have hundreds of approval certificates to their name and maintain a meticulous safety record. Facts: bolt-in bar chromoly steel 1.5-inch diameter tubing, .098 wall thickness tubing. Bars which connect to the main hoop, use a connecting joint system. Tig welded. Retains full seat adjustability. Semi-gloss black finish. Cost effective for club sport use. We recommend adding the harness bar, part...(choose a part on the right to read more)
$1,284.80
Make a selection HEI981001001S Heigo motorsports has been building extremely safe roll cages and roll bars for Porsche vehicles for 30+ years. They have also produced countless factory and motorsports bars and cages for the marque over the years. Chromoly steel 1.5 inch diameter tubing, .098 wall thickness tubing. A true bolt in bar that does not require drilling or welding. Includes a harness bar which is located on the b-pillar hoop. Bars which connect to the main hoop, use a connecting joint system so that you can easily access the motor without the use of tools. Tig welded. Retains full seat adjustability. Factory seat belts or 5-6 point belts can be used. Semi-gloss black finish. The front hoop mounts to the upper bulkhead, in the OEM m...(choose a part on the right to read more)
$1,428.90
Make a selection 000924T Why buy a rebuilt engine or transmission from us when your mechanic says he can do it cheaper? Because at Automobile Atlanta, we don’t compromise your rebuild with substandard parts or machine work. We go overboard in replacing parts your mechanic would never think to or can’t readily purchase. Plus, from years of experience, we know what wears out. Our rebuilt engine or transmission will, with care, last as long as the new factory one. Our setup is without compromise. We have invested thousands in Porsche factory tools to insure our engines and transmissions are “spot on”. Finally, they are extensively checked during each step of the rebuild process so your new engine is ready to bolt-in and drive away...(choose a part on the right to read more) General Fitment924 1980-85924 1976-79
$6,307.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |