Porsche 914 3 piece seat recovering kit 1972-1974.
Everything you need to perfectly recover your 72-74 brick weave insert seats with factory look material. Even the concours judges won't be able to tell.

Replacement metal backing plate and a roll of early black leatherette for replacing the dash face. includes enough material to cover the new dash plate and glove box door.

Consists of four lines, the two through the right engine shelf and the two through the tunnel. designed by our fellow 914 enthusiast chris foley, they are a perfect fit replacement to the discontinued factory varieties.

At last a factory look center console package with gauges and sending unit and harness almost identical to the factory original nla part. package consists of the factory duplicate reproduction center console, the special heater lever, the reproduction console wiring harness, the plastic heater lever bezel, the factory reproduction clock, volt meter, and temperature gauge, the temperature gauge sending unit, the sending unit plate and the sending unit o ring. Everything you need to install this beautiful assembly into your car and update it to the appearance group package offered originally when the car was new. This item is made to order and will take 4-6 weeks.

Consists of four lines, the two through the right engine shelf and the two through the tunnel. designed by our fellow 914 enthusiast chris foley, they are a perfect fit replacement to the discontinued factory varieties.

This kit is for most of the rubber grommets in your car. made by the German manufacturer wurth, these substitute for the impossible to find factory original and aid in the reassembly of your car.

Like new

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

• provides additional rear toe adjustment
• oem link is non-adjustable and eccentric bolt provides limited adjustment range, causing excessive tire wear and handling issues.
• helps maintain proper rear end suspension geometry
• each kit includes pair of 2 links

Includes:

set of driver and passenger side late latch housings
set of driver and passenger side latch hooks
set of 2 latch hook springs
set of 2 retaining rings
set of 2 washers
set of 4 press rivets

Stainless steel 4 point 914 hood pin kit

1970-1976 Porsche 914

Kit includes:
Laser cut 14ga 304 stainless steel base plates (qty 2)

Laser cut 20ga 304 stainless steel scuff plates (qty 4)

3-1/2" x 3/8" clear anodized aluminum hood pins (qty 4)

Stainless steel locking clips (qty 4)

Blind rivets and hex nuts

Another patrick motorsports usa exclusive - sold as a set - 1 per car

Alternate part numbers: bod 914gt hpk pms / bod-914gt-hpk-pms / bod.914gt.hpk.pms / bod914gthpkpms

This kit has three 16 ga (.06”) steel panels and will significantly stiffen the 914 chassis by tying the two longitude panels and the firewall together to "box" the frame. This kit requires welding and should be performed by a professional. Some modification will be required to install the panels. If you are upgrading your 914 to a six cylinder, doing autocross, or if you simply want to stiffen up the whole chassis, this kit is for you.
Comes with pdf installation instructions upon request.

Stainless cylinder air baffle kit
Includes:
(6) 930 106 228 00 prm
(4) 930 106 023 00 prm
(2) 930 106 221 00 prm
(2) 930 106 222 00 prm

Contains: (qty.) (4) retaining pins (2) spring clips (4) securing clips (2) retaining springs

Two 3d printed repair latches. 2.5 mm thick. Strong and flexible material is used. To simplify the process, use jb kwik two part glue instead of screws.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Tech tip: renew the ims bearing when replacing/renewing the clutch or all 100,000 km.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Features
• improved two piece 996 GT3 lower control arm design
• stronger than cast motorsport cup arms
• allows proper camber adjustment
• uses GT3 shims to adjust camber & lower control arm length (sold separately)
• high-strength steel alloy spherical bearings, completely serviceable unlike the motorsports arms
• sealed monoball inner bearing
• allows easy access to inner arm hardware
• includes adjustable thrust arm bushings to adjust caster and wheelbase
• a must have for all track and race enthusiast
• each kit includes pair of 2 arms
• fits both front and rear axles
• compatible with all 996/997/987/981 models except GT4

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Front; one kit per control arm