Vehicles
Sections
195 not categorized PORSCHE 356 C IMS KITCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 928 1992-95 (includes uncategorized and accessory items) 100555993RS This is a complete floor carpet kit for coupe models. This set is a lightweight fine German velour that is trimmed in vinyl. Each is cut, sewn and trimmed to fit perfectly. Drivers side vinyl heel pad and side pads (like original) is also included. Made in Germany. Sold individually.
$1,745.70
Make a selection 100555110NFB This is a rear lightweight carpet kit for a rs model or a rs tribute, without back seats. This set is made from German nadel filz. We go to extra lengths to ensure that our carpets are made as closely to the originals as possible. Each is cut, sewn and trimmed to fit perfectly. Details: German nadel filz (needle felt) trimmed in vinyl made in Germany custom made to order sold as a set. 1 necessary per car. Please note: when placing your order, we require the year, model and a list of any interior upgrades like roll bars, etc. This kit is custom made to order.
$1,096.70
Make a selection 100555964CA This is a complete floor carpet kit for cabrio models. This set is a lightweight fine German velour that is trimmed in vinyl. Each is cut, sewn and trimmed to fit perfectly. Driver's side vinyl heel pad and side pads (like original) is also included. Made in Germany. Sold as a set. 1 necessary per car.
$1,544.40
Make a selection 911051 Porsche 911 ac compressor upgrade kit, 1984-89, lh drive model provides improved integrity with our kuehl barrier hose set, kuehl low- high pressure switch to help protect the system, a new denso factory compressor with clutch, new kuehl drier, complete o-ring kit, along with r134a charge port adapters. you can use either r12 or r134a with refrigerant with this complete kit. all barrier hoses match OEM configuration, have sae sae approved crimped fittings and each hose is labeled so you know where it goes.
$1,097.00
Make a selection 92835194903 Oem compound sourced in Germany to ensure quality, reliability and precise fitment. Not sure which shims and sensors you need to go with these pads? Be sure to check out our brake service kit section, we combine the proper brake wear sensors, damping plates and pads for a complete installation. Sold as a set. 1 necessary per car. View/Change Diagram
From $61.40
Make a selection 91135295005EQ If your brake pads are at the end of their service life you will experience vibration, squealing, a pulsating brake pedal or poor response under heavy braking. We recommend replacing them as soon as any of the above signs are noticed. Also, be sure to inspect the rotors when changing the pads. For convenience, we sell complete rotor and pad kits, simply check under brake service kits. This pad set contains textar OEM (original equipment manufacturer) parts that we source in Germany to ensure quality, reliability and precise fitment. Textar brake pads are precision engineered to offer maximum safety, performance and comfort. This uncompromising approach has been the very ethos of textar for more than 100 years. ...(choose a part on the right to read more)
$73.70
Make a selection 914911356GROMKIT This kit is for most of the rubber grommets in your car. made by the German manufacturer wurth, these substitute for the impossible to find factory original and aid in the reassembly of your car.
$52.47
Make a selection FVD3522P29024A Brembo's brake systems are designed to meet the the needs of the most demanding of customers. Brembo brake systems originate from racing components and offer proven on-track performance. Brembo high performance systems offer a significant reducuction in usprung weight for better handling and provides maximum braking force without the flex of sliding callipers. Brembo components reduce heat-related stress and increase brake performance for a better overall pedal feel with less fade. Brake kits come with aggressive pads that last longer than OEM and provide the highest level of performance. Brembo brake systems also consist of a ventilated, integral or composite brake disc, light weight aluminium calipers, steel...(choose a part on the right to read more)
$4,174.50
Make a selection BBI9974010001 Features
$1,895.00
Make a selection BBI9965010002 • provides additional rear toe adjustment
$875.00
Make a selection FVD33150005 Restore proper suspension geometry with this adjustable lower rear control arm. The factory control arm cannot compensate enough when lowering your Porsche, leaving you with as much as ½ inch of toe in. The result is poor handling and rapid tire wear. This kit will provide the additional adjustment needed. The adjusting link has a left and right hand thread on each end. Rotating the link will increase or decrease the overall length of the arm. A precision teflon lined spherical rod end replaces the compliant rubber factory bushing for improved suspension response and feedback, and also reduces toe changes during acceleration and deceleration. Sold in pairs. 1 necessary per car.
$764.50
Make a selection FVD20798700 This FVD motorsports oil pump kit is a must for 987.1 Caymans and Boxsters driven on the track. Our kit includes a second return oil pump and our FVD motorsports oil pan. The issue: the 987.1 Boxster/Cayman from 2005 to 2008 has the factory return oil pump located on the right rear side. On the left side, the return oil pump located in front. So when driven fast in right turns, the oil from the camshaft case (rear left) does not flow back quickly enough into the oil pan. When the oil pan is starved of oil, the oil pump sucks in air and over time the motor will seize. The solution: our tandem return oil pump draws oil from the camshaft housing in (rear left, 3rd cylinder) and feeds it back into the oil pan so th...(choose a part on the right to read more)
$3,274.30
Make a selection BBI9964010002 Finally, a complete solution to properly widen the front track width of a Porsche 996 and 997 turbo. To help increase front end grip, this kit allows full negative camber adjustment without binding the axles and fitment of wider wheel/tire combinations and GT3 cup car fenders. Each kit includes lower control arms, thrust arms, axle spacers, upper mounts, and camber shims.
$3,695.00
Make a selection F9164120103 Instrument faces are one of the most visible and frequently looked at components in your Porsche. When making the decision to change them you want to ensure that you select a high-quality product like your originals. Each of our sets are made in Germany and use the factory scripting (font). Our faces also offer the same uniform night time shading and include the original die cut notches for easy installation. Each kit varies, so simply pick out the faces that match your originals. They are available in a variety of colors to make a bold statement, or to match exterior paint schemes. Don't see the color or combination that is right for your car? Or perhaps you want a custom logo in the tach? Kindly contact us f...(choose a part on the right to read more)
$843.70
Make a selection BBI9963010001 The bbi autosport Porsche 996/997 turbo clutch slave cylinder conversion kit is a direct replacement part that eliminates the problematic factory power-assist system for improved reliability and pedal feedback. The factory power-assisted clutch system has always been the achilles heel for the Porsche 997 turbo. Utilizing the power steering system to help reduce the force needed to depress the clutch pedal, it is a flawed design that delivers a mushy pedal feel with poor feedback, and is highly prone to failure.
$1,330.00
Make a selection BBI9964010001 Features
$525.00
Make a selection 99660610599 If you are noticing engine vibrations, misfires and even backfiring your crankshaft position sensor maybe bad. Your car's dme (ecu) uses the signal from the crankshaft position sensor to control ignition timing and fuel injection, so if your sensor is failing your engine is suffering from poor timing and is not running efficiently. This kit is complete and ready to install.
$132.77
Make a selection FVD20799601 Scavenging and aeration in the oil pan have been identified as a problem in 996 and Boxster models experiencing high g-forces on the racetrack. This oil pan spacer provides a simple solution. This spacer increases sump capacity by half a liter, providing more reserve to ward off starvation. Thisoil pan spacer clears all factory options including the rear skid plate. Added oil capacities as well as increased oil pan surface area increase oil cooling and engine performance. *oil pan and sump baffle are OEM parts and do not need to be purchased material: 6061 t6 aluminum alloy finish: clear anodized weight: n/a models: Boxster, Boxster s, and 996 models (excludes GT3 and turbocharged models) installation: for best...(choose a part on the right to read more)
$283.80
Make a selection FVD20703500 This oil cooler kit is a must for engines that are modified. It reduces oil temperature and protects the engine. This kit can lower operating oil temperature up to 60* f. Simple installation without cutting or modifying. High quality behr cooler ensures reliability without sacrificing a/c performance as kit is mounted clear of the front a/c condenser. Can be mounted on cars with or without air conditioning. Sold as a complete kit, ready for installation.
$2,981.74
Make a selection FVD123025ATK K24/26 exchange turbo (only OEM k24 exchange accepted) (up to 700 hp) power is focused on mid and top range rpm's. Facts: - modified compressor housing and backing plate - modified & lightened high flow compressor wheels. - remanufactured by kkk / borg warner certified technicians - free software update for those already running FVD software. FVD brombachers 996 k24/26 race turbos are new units created for those who are looking for ultimate in performance. Power is focused in the mid and top rpm range while keeping turbo lag low. They are completely bolt on and do not require custom headers or special modifications. The factory OEM turbocharger compressor housing is re-profiled and the compressor backing plate...(choose a part on the right to read more)
$2,976.60
Make a selection FVD123019ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection FVD12399600R Silicone boost hose kit FVD's direct replacement boost hose kit eliminates common boost hose "blow outs" on modified turbo's. Facts: tested to withstand over 75 psi (5 bar) boost pressure.fuel and oil resistanttemperature range between - 50 to + 180 degreesbolt on kit over time the OEM boost hoses tend to expand and contract under higher load, which leads to leaks, or "blow outs". Also, the OEM aluminum end does not secure properly into the intercooler, which causes boost leaks, and boost hose blowouts. Our machined billet ends are a perfect secure fit and our silicone hose is designed not to expand under boost pressure. The hose kit is a complete bolt on kit.
$590.70
Make a selection FVD123013ATK K-16/24 turbo (up to 555 hp) power is focused on low and mid range rpm's. Facts: larger compressor wheel with extended tip. 47.5mm inducer diameter. Cnc modified compressor housing modified and improved back plane uprated staggered gap turbine uprated thrust bearing modified wheel to reduce backpressure balancing of all components factory vacuum unit new bearings and seals all parts are reconditioned and balanced FVD brombachers 993 k-16/24 remanufactured turbos are created for those who are looking for power that is focused in the low and mid rpm range. They are completely bolt on and do not require custom headers or special modifications. The remanufacturing process starts with re-profiling the OEM turbochar...(choose a part on the right to read more)
$2,976.60
Make a selection FVD33396500 A cost-effective combination of bilstein b6 shocks with a set of German h&r lowering springs. This kit is a perfect balance of performance and comfort for street use. Benefits: optimum adhesion and enhanced stability for daily driving and extreme driving situations. Lower stance at 1.3 inches (35 mm) front / 1.18 inches (30 mm) rear. Marked improvement in safety and sportiness. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Please note: if you would like to reduce the ride height, please order part # 115110016 which will lower the stance by another 1.5 inches (40mm).
$2,730.94
Make a selection FVD347088 The momo prototipo is a classic wheel using a combination of the finest modern materials giving it the perfect blend of old and new. Made from top grain leather with white stitching, black cut-out spokes and includes a momo horn button. Momo prototipo is the excellent choice for those wishing to retain the character of their vehicle while refreshing the interior. Style: rally color: black material: leather spoke finish: black horn: matte black with momo horn button diameter: 13.78 in (350 mm) rim diameter: 1.29 in (33 mm) dish: 1.4 inch (37 mm) weight: 2.86 lbs. (1.3 kg) please note: this kit is only for cars without an airbag. Vehicle-specific hub adapter required.
$297.00
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |