PORSCHE 924 GT WIL VICan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: BOXSTER 2009-11 - Uncategorized (includes uncategorized and accessory items) 93060610500ATK The remanufacturing process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, clean, degrease and rebuild to factory specifications. Remanufacturing is done in Germany, so the lead times can vary. Send us your original warmup regulator and we will have it remanufactured for you. We do not offer a core exchange on this part. Please note: please package your part as carefully as possible to ensure that damage is not caused en route to us.
$744.70
Make a selection
$119.00
Make a selection 94A Oversize shipping charge will apply.
$649.00
Make a selection 96410605131 This fan hub sits between the cooling fan and the alternator. It should be checked periodically for noise as it contains a bearing which can fail. Please note: 964 106 051 30 has been superseded by 964 106 051 31. If you are replacing 964 106 051 30, you will also need 3 qty., part # 90007609101 to install the new superseded hub. Sold individually. 1 necessary per car.
From $191.40
Make a selection 028129087 By now even the sheltered front blower box hose has deteriorated to the point of looking bad. Easily renewed, order the 2.25 size for the blower box connections and the 2.0" size for the side dash vents. One hose length will replace one side. The seal, often overlooked, seals the blower box to the cowl and prevents water from entering this critical area. Easily replaced with the blower box still in the car, this would also be a great time to clean the 1973-76 blower grille! One length does both sides.
$13.50
Make a selection 150SPB965 Replace the worn-out spring plate bushing with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is the inner bushing for the 1-piece non-adjustable spring plate. Sold individually. 2 necessary per car.
$47.30
Make a selection 21011123 Catalytic bypass pipe "x torque" design made by m&m in Germany. The x torque design in is a true x pipe design. It is open in the center to add backpressure for torque. Give's you 10-15 ft-lbs of torque in the mid range along with 10-15 hp in the higher rpms. Why settle for the traditional cross over cat design when you can add torque in the mid range where the 996's need it most! Dme programming is necessary. Without it you will get a check engine light (cel). Tech tip: for older cars repair-kit FVD mk 996300
From $764.50
Make a selection 150PB10134 Replace worn-out original sway bar drop link bushings with this longer lasting poly-graphite plastic bushing set. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. The set includes 4 complete bushings and 4 sleeves (8mm inner diameter). Sold as a set. 1 necessary per car.
$73.70
Make a selection 150PB1027 Replace worn-out original sway bar bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. We also recommend replacing the sway bar to ball pin bushing at the same time to save on labor costs, part # 90134378200 sold individually. 4 necessary per car. Please note: this fit's 911 models from 1978-89 if fitted with an 18mm original rear sway bar.
$49.50
Make a selection 17021102501 This is a high-quality replacement for original number, 930 211 025 01 manufactured by dansk. It is manufactured in steel and includes a corrosion resistant protective coating. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911102 sold individually. Right or left side fitment. 2 necessary per car. Please note: this will not fit u.s. 3.0 l SC mode...(choose a part on the right to read more)
$642.40
Make a selection 190111043B For use on obd1 (94 and earlier) cars only! Only 1 o2 bung is provided. Call for 1995 application. Will not work with multiple o2 sensor cars, like north american cars. (96-98) does not include a TUV-certificate. We recommend using our catalytic installation kit, part # FVDmk993300b please note: not legal for use on california pollution controlled motor vehicles.
$556.60
Make a selection 150TBF900 Replace worn-out original front control arm / wishbone bushings with this longer lasting poly-graphite plastic bushing. Poly-graphite is higher density than OEM rubber so suspension components will experience less deflection. It is specially formulated with a graphite lubricant to produce a bearing like action. This is located at the front of the control arm / wishbone. The correct matching poly-graphite bushing for the rear of the control arm is part # 150tbr900 sold individually. 2 necessary per car.
$48.40
Make a selection 21011196402 Say good bye to the days of having to weld and cut aftermarket sport cats to make them fit! We have our sport cats made in Germany to our specifications and that means that these are 100% bolt on without issue! - + 10 crank hp & +6 crank torque. - 200 cell, tri metallic German hjs sport catalysts. - large volume o 105 mm (4.1 inch diameter) high flow cat. - exhaust hanger brackets are included so that the heat shield does not have to be removed. - weighs 7.2 lbs. (3,2 kg). - direct bolt on replacement. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - reduces backpressure and thermal stress. - made in Germany. - more distinguished flat 6 growl at wide open throttle. The FVD 200 cell...(choose a part on the right to read more)
$1,593.90
Make a selection 115343993008L If you are looking for a shock to combine with lowering springs or firmer springs the bilstein b8 is the ideal solution. These offer more performance than the b6 as the valving is more firm. These will pair well with h&r or eibach lowering springs, however you can also run them with euro mo30 (row) springs and mo33 springs. The product benefits at a glance: shortened high-performance shock absorbers for virtually every lowering spring set. Marked improvement in safety and sportiness with additional spring changes (lowering). Sporty feel, yet still comfortable. Offers precise handling and optimum control. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Road-tested an...(choose a part on the right to read more)
$524.70
Make a selection 100211025SSUSA If you have a us model 1980-83 911 SC and are looking to replace your heat exchangers we have some good and bad news. The original heat exchangers (part # 930 211 025 02) are no longer available from Porsche. But, these stainless-steel industries (ssi) heat exchangers will work with modifications. The good news is, once done, you will have more torque and horsepower! Free flow conversion heat exchangers improve sound and performance, while reducing backpressure and thermal load on the motor. These are based off the early style exhausts found on the 1974 2.7 l rs. Those models had a straight through, superior, free flow exhaust design that included a dual inlet muffler. When converting to these heat exchangers y...(choose a part on the right to read more)
$2,863.30
Make a selection 00004490042 Cabriolets are not known for having great acoustics inside the passenger compartment. However, the new Porsche Boxster high performance audio system changes all that. Explicitly designed for the interior and layout of the Boxster, the system delivers outstanding performance with either the roof on or off. The specially designed amplifier delivers two channels of 160 watts each, powering 2 ohm speaker sets. Two high-quality mid-range/tweeter systems coupled with a dual bass system in the door deliver incredible sound while being elegantly integrated within the Boxster's interior. Installation requires some knowledge of stereo installation, but in general is not too complicated. Beethoven or boston, the music wi...(choose a part on the right to read more)
$4,214.03
Make a selection 1150009 These are made with club sport events in mind. They work with stiffer springs and lowering springs (we recommend h&r or eibach) and have a fully threaded body for individual lowering like the original 993 cup suspension. You will need to run our drop links for the sway bar, part # FVD333900. Lowering is adjustable to 30 mm (1.18 inches) left or right side fitment. Sold individually. For matching front club sport shocks, please order part # 1150002li for the left and part # 1150002re for the right. For a properly spec'd complete kit including front and rear club sport shocks with lowering springs and rear drop links, please order part # FVD33399300.
$382.80
Make a selection 22011090102ATK Sport throttle bodies are a great addition for those with highly modified cars. They are a great addition for those with full exhaust systems (larger diameters), maf kits, larger displacements, street or race cams, etc. The remanufacturing process includes full inspection of your throttle body to ensure proper operation after the remanufacturing process. We then disassemble and bore the original to a 2.7-inch (70.5 mm) diameter. The entire throttle body is cleaned, degreased and the internals are polished to create more laminar flow. We then machine the shaft to accept larger butterfly's which seamlessly match the bore. All clearances are checked for precision to ensure reliability. Each throttle body is reman...(choose a part on the right to read more)
$589.60
Make a selection 115343993008R If you are looking for a shock to combine with lowering springs or firmer springs the bilstein b8 is the ideal solution. These offer more performance than the b6 as the valving is more firm. These will pair well with h&r or eibach lowering springs, however you can also run them with euro mo30 (row) springs and mo33 springs. The product benefits at a glance: shortened high-performance shock absorbers for virtually every lowering spring set. Marked improvement in safety and sportiness with additional spring changes (lowering). Sporty feel, yet still comfortable. Offers precise handling and optimum control. Bilstein gas pressure technology. Bilstein mono-tube/upside-down technology. Made in Germany. Road-tested an...(choose a part on the right to read more)
$524.70
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 846R9001R01 Material: tig welded, type 304, stainless steel. Finish: satin finish stainless. Weight: 6oz. Models: 996/997, Boxster, 911 & 944. Installation: secures snap-in lap belts to factory tunnel side (inside) seat belt mounting point. Miscellaneous: allows user to remove and install belts in seconds. Will not interfere with factory seat belt. One pair will work for both seats. Note: part# 846 r9002 hardware kit is required for installation in (1985 - 1989) model Porsches. Use part 846 r9003 for outside belt mount.
$69.30
Make a selection 91151192302EQ This gasket sits on the inside of the hood in the front trunk. It tends to get nicked and cut and will degrade with time. It is essential to keep moisture out of the trunk and should be replaced at the first signs of damage. Sold individually. 1 necessary per car.
$136.40
Make a selection 930602015AX3ATK Send us your distributor and we will remanufacture it for you. A perfect option for those who have time and want to save on costs. The remanufacturing process includes full inspection, disassembly, cleaning and degreasing. We then install a toothed timing belt, 3 German made top bearings, 1 German made lower bearing and a distributor pinion pin (part # 930 602 922 00). Clearances, timing and proper operation are then checked to ensure reliability. Please note: each distributor is remanufactured in Germany, so the lead times can vary.
$1,393.26
Make a selection 90110390200K Refresh the missing horsepower with a brand new set of pistons and cylinders. Restore the lost compression that reringing will never accomplish. Other kits available for large displacement.
$3,938.55
Make a selection 90110511511EQ High-quality, cost effective OEM replacement for original part # 901 105 115 03. This cover is designed and manufactured to perform like the original. Please note: this cover does not have the Porsche logo stamped on it like the genuine part. If that is a concern for your build or restoration, please order 901 105 115 11 this will require 6 qty. Washers 90003101430 and 6 qty. Self-locking hex nuts 90008400403 sold individually. 2 necessary per car.
$104.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |