Vehicles
Sections
443 not categorized PORSCHE CAYENNE CHECK OUTCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: CAYMAN 2006-08 (includes uncategorized and accessory items) FVD10699702 This radiator is produced by the racing & high-performance division of csf who design, engineer and manufacture the most advanced, efficient, and reliable cooling systems in the world. Csf manufacturers all aluminum high performance radiators that are a direct-fit replacement for Porsche racecars and streetcars. Csf radiators improve cooling efficiency by 10-20 % over the factory radiators. Each radiator is stamped to the same geometry and includes aluminum end tanks that offer more reliability than the factory plastic end tanks. Each csf end tank features quality welding and is generally considered the strongest tank design in the industry. If you are planning to upgrade or replace your radiators, we highly re...(choose a part on the right to read more)
$548.90
Make a selection FVD111046 Is your exhaust tip a little old and unappealing to look at? Update it with a more aggressive look. Made from t304 stainless steel with a polished finish. 4 round to fill in the entire bumper cut out. Angle cut to complement the rear bumper. Sold individually. 1 necessary per car.
$162.80
Make a selection FVD116917 This sachs racing 4 puck disc with sintered metal plates and torsion springs has a higher friction coefficient than plates with organic friction material. That allows for higher transmittable torque (405 ft lb. / 550 nm max.) and makes them more dirt and oil resistant. This disc has an aggressive start performance (small clutch pedal release window) so is best suited for race use (endurance races, hill climbing, slalom and rally's). It is assembled by hand, which guarantees the highest quality attributes both in terms of clamping load and release characteristics. This disc is a rigid disc (un-sprung) and is purposefully built to be used with the original dual mass flywheel (dmfw) which includes dampers / sprin...(choose a part on the right to read more) General FitmentCAYMAN 2006-08BOXSTER 2005-08 BOXSTER 1997-04
From $598.67
Make a selection FVD116981GT4 Hailing from the baden wurttemberg region in Germany, speaking the language and dealing with lead engineers from the OEM and motor sport manufacturers for more than 30+ years has many advantages. This FVD exclusive clutch kit is culmination of zf sachs race engineering gmbh parts and an aasco motorsports lightweight flywheel that have been developed to work together without compromise. This kit offers a silky-smooth release, superb drivability, can handle more torque than comparable clutch kits. We specifically chose a clutch disc with torsion springs that function as a vibration damper between engine and gearbox that is necessary when removing the factory dual mass flyweel (dmfw). It also means that you will e...(choose a part on the right to read more)
$2,638.90
Make a selection FVD123019ATK Our k24 sport turbocharger is based off the optional k24 turbochargers, found in the GT2 or 993 turbo x50 models. They are remanufactured by borg warner certified technicians in Germany and are a cost-effective solution. The remanufacturing process includes full inspection of the turbocharger to ensure proper operation after the remanufacturing process. We then disassemble, clean and degrease the unit. The compressor wheels are exchanged, lightened and modified for more air flow. All clearances / shaft tolerances are checked for precision to ensure reliability. The end result is 20-30 additional horsepower, in the low and mid rpm range over the factory turbo. The sport turbo also has less lag than a factory k24...(choose a part on the right to read more)
$2,042.70
Make a selection F91641200TUM041 The differences are day… and night! Gauge faces are one of the most visible and frequently looked at components in your Porsche. Why skimp on quality? Gauge faces should have clearly visible markings and be easy to read with and without back lighting. Replacement faces should offer similar qualities, but many gauge faces on the market don't quite make the grade. FVD gauge faces are different. What makes them different you ask? See for yourself. In the below pictures you will see that the tiptronic is an FVD gauge face and the 6 speed gauge face is the competitions. The daytime difference (the competition): darker, more yellow appearance raised orange warning lights, not flush larger, bolder script than t...(choose a part on the right to read more)
$858.00
Make a selection FVD211328490 Required when adding a free-flow exhaust system with the part # FVD 211 328 489x or FVD 211 328 489xx. Also required when adding dual outlet heat exchangers or dual inlet mufflers. Sold as a kit. 1 necessary per car.
$1,288.80
Make a selection FVD3310212291 Our rear trailing arm bushings contain rubber inserts with a shore hardness value of 85, like what is used on rennsport models. It offers rs style handling characteristics, superior durability and is still forgiving enough for street use. - better handling. - makes precision adjustments of the suspension easier. - does not produce road noise. - shore hardness value of 85. - direct OEM replacement. - more forgiving for street use. -includes press tools and grease for easier assembly. Sold as a set. 1 kit is necessary per car. Please note: this fits the 964 c2 / c4 and rs america. Not keen on installing or having the bushings installed at a shop? Please check out our part # FVD33399603b8 and FVD33399603b8, we wil...(choose a part on the right to read more)
$902.00
Make a selection FVD332987CQU This helical lsd differential is a direct replacement for the standard Porsche open differentials. suitable for Porsche 987 Boxster s and Cayman s models. automatic torque biasing differential enables your car to accelerate quicker and corner faster. General FitmentBOXSTER 2005-08CAYMAN 2006-08
$1,860.10
Make a selection FVD20703500 This oil cooler kit is a must for engines that are modified. It reduces oil temperature and protects the engine. This kit can lower operating oil temperature up to 60* f. Simple installation without cutting or modifying. High quality behr cooler ensures reliability without sacrificing a/c performance as kit is mounted clear of the front a/c condenser. Can be mounted on cars with or without air conditioning. Sold as a complete kit, ready for installation.
$2,981.74
Make a selection FVD33150046R Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.
$66.00
Make a selection FVD332944QDF A direct replacement for the standard Porsche differential. Automatic torque biasing differential enables your car to accelerate quicker and corner faster. The differential powers both drive wheels under nearly all conditions. With an ordinary open differential (standard on most cars), precious power is wasted during wheel spin under acceleration. This happens because the open differential shifts power to the wheel with less grip, along the path of least resistance. The differential, however, does just the opposite. It senses which wheel has better grip, and biases the power to that wheel. It does this smoothly and constantly, and without ever completely removing power from the other wheel.
$2,013.00
Make a selection FVD33150040R Replace worn-out original rear sub frame (side panel) bushings with our FVD clubsport series. They are made of rubber with an 85 shore hardness value, that is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. This bushing is made in Germany. It is crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85 shore hardness value core. This is a front and rear bushing for one sub frame. 2 are necessary per car. We also sell the entire right and left rear sub frames with these bushings already installed, please order our part # FVD331993001.
$429.00
Make a selection FVD34101807ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD333505001 Without ( i030 ) sport suspension set contains: - 2 x 993 333 107 01 - 2 x 996 333 105 02 also c4s cabrio with standart suspension
$166.34
Make a selection FVD34101707ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD34101702RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection FVD34101802ATK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD clubsport front control arm bushings, part # FVD341999r. They are made with 85 shore rubber (like the rennsport model). Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrangements can ...(choose a part on the right to read more)
$418.00
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD34391101SET Replace worn-out original front lower control arm bushings to return your car to its intended suspension geometry and steering feedback. Features: better handling reduces that sloppy steering feel does not produce any noise like the teflon bushings. Rubber has the original shore hardness value of 65 (like oem) fit's like oem, simple installation made in Germany if you are looking for a sportier upgrade we suggest our sport lower control arm set, part # FVD34391192set. Set is sold per axle. 2 necessary per car.
$152.90
Make a selection FVD33150045R Replace worn-out soft rubber (65 shore hardness value) control arm bushings (camber link and caster link) with sportier rubber (75 shore hardness value) that is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$69.30
Make a selection FVD3511B18033A This line is dedicated to the most demanding customers.this braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminium calipers, a complete set of high performance brake pads, metal braid tubes and high quality small parts. Please remember that in the European community, gran turismo products may only be used in racing and on private roads, unless you have obtained a new approval in compliance with directive 98/12/ec. Proven on-track performance; disperses gasses, cleans pads for better 'bite'; reduces 'usprung weight' for better handling; provides maximum braking force without the flex of sliding callipers; reduces heat-related stress, increases ...(choose a part on the right to read more)
$4,175.60
Make a selection FVD3511G29016A This line is dedicated to the most demanding customers.this braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminium calipers, a complete set of high performance brake pads, metal braid tubes and high quality small parts. Please remember that in the European community, gran turismo products may only be used in racing and on private roads, unless you have obtained a new approval in compliance with directive 98/12/ec. Proven on-track performance; disperses gasses, cleans pads for better 'bite'; reduces 'usprung weight' for better handling; provides maximum braking force without the flex of sliding callipers; reduces heat-related stress, increases ...(choose a part on the right to read more)
$6,409.13
Make a selection FVD3511N29518A This line is dedicated to the most demanding customers.this braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminium calipers, a complete set of high performance brake pads, metal braid tubes and high quality small parts. Please remember that in the European community, gran turismo products may only be used in racing and on private roads, unless you have obtained a new approval in compliance with directive 98/12/ec. Proven on-track performance; disperses gasses, cleans pads for better 'bite'; reduces 'usprung weight' for better handling; provides maximum braking force without the flex of sliding callipers; reduces heat-related stress, increases ...(choose a part on the right to read more)
$5,384.50
Make a selection FVD3511B18022A This line is dedicated to the most demanding customers. This braking system originates from the racing components, consisting of a ventilated, integral or composite disc, aluminum calipers, a complete set of high performance brake pads, TUV/dot homologated metal-braided brake hoses and high quality fastener hardware. Calipers are available in red, black or silver. Proven on-track performance; extraordinarily powerful and consistent under the repeated loads. Disperses gasses, cleans pads for better "bite". Reduces "un-sprung weight" at each corner for better handling. Provides maximum braking force without the flex of sliding calipers. Reduces heat-related stress, increases brake performance and pedal feel. ...(choose a part on the right to read more)
$5,959.21
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |