Vehicles
469 not categorized PORSCHE 930 A C CONTROLCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.FVD33150045 Original rubber replacement bushing (65 shore hardness value) for the rear control arms (camber link and caster link). This bushing cartridge is weather sealed and is crafted in high carbon steel and 7075 t6 aircraft aluminum. Sold individually.
$64.90
Make a selection FVD34101702AT By ordering this part number you get after previous sending in General Fitment911 1994-98
$417.56
Make a selection FVD34101707AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. The reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD341999r. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform you immediately. General Fitment911 1989-94
From $418.00
Make a selection FVD211622 This silicone hose supplies hot air to the heater control box, it replaces original part # 930 211 622 01. It runs from the exhaust heat exchanger to the heater control box. We recommend replacing the heater box clamp, part # 90121105122 on one end and a hose clamp part # 99951234902 on the other end. Sold individually. 2 necessary per car.
$52.80
Make a selection FVD34101802AT By ordering this part number you get after previous sending in General Fitment911 1994-98
$417.56
Make a selection FVD34101802RAK Unsure about installing replacement bushings and bearings? Send us your control arm and we will properly recondition and install the bushings and bearings for you. The reconditioning process includes full inspection of your track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we will properly install our FVD race front control arm bushings. They are made with uniball bearings so suspension motion is accurately repeated in every corner. Please note: each control arm is remanufactured in Germany, so the lead times can vary. If we cannot remanufacture your control arm we will notify you as soon as we can. Arrange...(choose a part on the right to read more)
$438.90
Make a selection FVD34101807AT By ordering this article number, you will receive a reconditioned wishbone with newly pressed-in bearings. The calculated replacement deposit will be returned to you as soon as the old part has been received and checked. The reconditioning process includes full inspection of each track control arm to ensure proper operation after the remanufacturing process. We then disassemble, degrease and completely clean it. Once fully prepared, we properly install our OEM front control arm bushings, part # FVD341999r. They are made with 65 shore rubber like the original control arms. If your old part is not repairable we will inform you immediately. General Fitment911 1989-94
From $418.00
Make a selection FVD34102700ATK By ordering this part number you get after previous sending in your wishbone overhauled with new race-silent blocs back. The race-silent blocs (85 shore) give you more stable driving. Should it not be repairable, we will inform you immediately.
$279.40
Make a selection FVD34102702ATK By ordering this part number you get after previous sending in your wishbone overhauled with new race-silent blocs back. The race-silent blocs (85 shore) give you more stable driving. Should it not be repairable, we will inform you immediately.
$279.40
Make a selection FVD34102802AT By ordering this part number you get after previous sending in your wishbone overhauled with new race-silent blocs back. General Fitment968 1992-95944 1982-85 944 1985-88
$501.41
Make a selection FVD34105307R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 2 are necessary per car. Please note: this does not include the lower control arm, the picture circled in red is just for reference. General Fitment911 GT3 2003-05911 TURBO/GT2 2001-05 911 1998-05 BOXSTER 1997-04
From $98.92
Make a selection FVD34199690 Allows greater camber adjustment possibilities at the front using the 2-piece split control arm set. General Fitment911 TURBO/GT2 2007-09911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
$2,638.72
Make a selection FVD34199691 Allows greater camber adjustment possibilities at the front using the 2-piece split control arm set. Includes 1, 2, 3, and 10mm shims to cover a wide range of camber adjustment. A must for track and club sport vehicles. General Fitment911 TURBO/GT2 2007-09911 GT3 2003-05 911 TURBO/GT2 2001-05 911 1998-05
From $1,849.17
Make a selection FVD341999R Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection FVD34391192SET Replace worn-out original front lower control arm bushings with our FVD sport bushings, made of rubber with an 85 shore hardness value that is the same as the rs models. 85 shore is more durable, provides more positive suspension location and is still quiet and comfortable for street use. Features: better handling reduces that sloppy steering feel makes precision adjustments of the suspension easier does not produce any noise like the teflon bushings. Rubber has a shore hardness value of 85 (like rs models) fit's like oem, simple installation made in Germany set is sold per axle. 2 necessary per car.
$158.40
Make a selection I203 Radio and heater control block off plates - until now, removing the center console from your 964/993 was not possible due to the required switches that were mounted in it. Rennline's new radio and heater control block off plates solve that problem. These plates have been specially designed to accept the factory switches installed in the center console of all 964/993 cars. Don't have the factory switches? No problem. These plates are also available without switch cutouts so you can install your own switches or gauges. Made from powder coated metal and installs in minutes on cars with the radio or heater controls removed. General Fitment911 1989-94911 1994-98
$50.00
Make a selection FVD95861890 Software control module - 958 Cayenne turbo 2011+ General FitmentCAYENNE 2011-14
$1,094.50
Make a selection FVD561997A Installation time: about 15 minutes General Fitment911 2009-12911 2005-08
From $471.90
Make a selection I206 Radio and heater control block off plates - until now, removing the center console from your 964/993 was not possible due to the required switches that were mounted in it. Rennline's new radio and heater control block off plates solve that problem. These plates have been specially designed to accept the factory switches installed in the center console of all 964/993 cars. Don't have the factory switches? No problem. These plates are also available without switch cutouts so you can install your own switches or gauges. Made from powder coated metal and installs in minutes on cars with the radio or heater controls removed. General Fitment911 1989-94911 1994-98
$50.00
Make a selection I200 Heater control block off plates - until now, removing the center console from your 964/993 was not possible due to the required switches that were mounted in it. Rennline's new radio and heater control block off plates solve that problem. These plates have been specially designed to accept the factory switches installed in the center console of all 964/993 cars. Don't have the factory switches? No problem. These plates are also available without switch cutouts so you can install your own switches or gauges. Made from powder coated metal and installs in minutes on cars with the radio or heater controls removed. General Fitment911 1989-94911 1994-98
$50.00
Make a selection FVD631997TLED This works on FVD bromacher led's, part # FVD 631 997 03 to make the daytime running lights dim when the headlights are turned on. This is also mandatory for FVD 631 997 fled if you want to have the daytime running lights dim when you turn the headlights on. General Fitment911 GT3 2007-11911 TURBO/GT2 2007-09 911 2005-08
From $477.00
Make a selection
From $22.11
Make a selection S745012 Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper suspension geometry on a lowered Porsche. The fk teflon-lined rod end bearings ensure precision handling and lock in your car's alignment settings, ensuring predictable cornering under all conditions. Unlike the competitors' product, rennline arms come with eccentric locks and new hardware so you can completely eliminate the factory setup, which is known to go out of adjustment under hard driving and ruin your car's alignment. Sold each, two needed per car. General Fitment911 1994-98
$306.90
Make a selection S727374101 If you're serious about how your 993 handles, you should upgrade the rear suspension with adjustable control arm links. There are two major drawbacks to the factory links: 1) you can't lower your car and maintain proper suspension geometry. The factory links create too much toe-in, which cannot be adjusted out, creating handling problems and excessive tire wear. 2) the factory links have rubber bushings, which make handling imprecise, especially in performance driving when suspension loads are highest. General Fitment911 1994-98
$1,758.90
Make a selection S735012 If you're serious about how your 993 handles, you should upgrade the rear suspension with adjustable control arm links. There are two major drawbacks to the factory links: 1) you can't lower your car and maintain proper suspension geometry. The factory links create too much toe-in, which cannot be adjusted out, creating handling problems and excessive tire wear. 2) the factory links have rubber bushings, which make handling imprecise, especially in performance driving when suspension loads are highest. Rennline adjustable control arm links solve both these problems. Manufactured from 6061 aluminum and feature a turnbuckle design that allows each arm to be lengthened or shortened as needed to restore proper su...(choose a part on the right to read more) General Fitment911 1994-98
$306.90
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |