Vehicles
235 not categorized PORSCHE 944T PARTS KITCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.
$538.42
Make a selection 0015400145 Ings n-spec kevlar front bumper Porsche 997 GT3 06+ General Fitment911 GT3 2007-11
$7,627.50
Make a selection 00004420012 This stainless steel sports exhaust system adds a fuller & more powerful sound to your Boxster. The distinctive tail-pipe design & bypass pipes echo the classic sebring exhaust while enhancing the striking rear looks of your Boxster. The sound is pleasant & mellow at idle & low rpms: as rpms increase more exhaust is channelled to the bypass pipes thus providing an increasingly sharper & more aggressive tone. At just under 5k rpm through redline it is in full bypass mode giving an exciting sound similar to the club sport cars. The sound is managed by an electical/vacuum control system allowing you to operate in stealth through the neighborhood yet providing that unmistakable pure Porsche sound as you power throu...(choose a part on the right to read more) General FitmentBOXSTER 1997-04
$3,749.42
Make a selection 021198009D You can’t rebuild without an engine gasket kit, even if you are reusing the hard parts! Remember in addition to order four baffle plate seals, a front and a rear main seal and maybe a couple of cv joint gaskets! General Fitment914 1970-76
$76.56
Make a selection 100105516 This is our camshaft of choice for our tuning kits as it offers unparalleled performance throughout the entire rev range. Performance gains of 30 hp can be had with upgraded boost springs, exhaust, etc. Drivability is enhanced for street performance. This cam is sourced in Germany to ensure quality, reliability and precise fitment. Specifications: 1.26 mm .10 mm the left side is our part # 100105514 General Fitment911 1989-94
From $1,063.94
Make a selection 091100810009 Just like every genuine techart product, each part of the techart aerokits has to undergo hard and demanding test procedures during its development process. In terms of aerodynamic components, wind tunnel testing is crucial for both, optimum driving performance and highest active safety. General Fitment911 2009-12
$5,393.25
Make a selection 10010303000TU Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders have extremely high thermal resistance and are nikasil coated to reduce wear and friction. We also have the piston rings (sealing and oil scrapers) pre-installed to ensure reliability. Each of our piston and cylinder kits are complete and ready for installation. Features: mahle forged 935 3.0 l turbo pistons mahle nikasil coated cylinders increased 7:1 compression = greater acceleration 95 mm pistons / 95 mm finned wr group 0 cylinders piston rings pre-installed piston pins and circlips are included complete set of 6 - ready for installation made in Germany we recommend the complete engine gas...(choose a part on the right to read more) General Fitment911 1970-73
From $6,197.50
Make a selection 091100340009 In the sense of technology, ideal is understood as the focus on the essential. In the meaning of the arts, it is the objective of the sensual execution of esthetics and beauty. And generally speaking, it is nothing less than the quest for perfection. At techart, they've focused on the essential for 25 years. General Fitment911 2009-12
$1,822.50
Make a selection 10010303803 The 11.8:1 compression will provide you with more acceleration than kits with 11.3:1 compression. However, this kit cannot be used with original cams, it requires a more aggressive cam (maximum valve lift (tdc) of 2.1 mm) and has very deep pockets for use with rsr valves. The 109-mm size means that the housings / case must be modified / machined on non rs models. If you have a European rs model, these would be slip fit. This kit also requires 6 qty. Larger o-rings, part # 96410440180 and 6 qty. Larger base o-rings, part # 99970502341 mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high th...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $6,784.84
Make a selection 10010303804 The 11.8:1 compression will provide you with more acceleration than kits with 11.3:1 compression. For track use we recommend more aggressive cam (maximum valve lift (tdc) of 2.1 mm) . Piston's have very deep pockets for use with sport valves. These are 107 mm in size so are slip fit and do not require modifications. This kit is ideal for track use but can also be used on the street, it will add 40+ hp (depending on your additional modifications). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resistance, they are nikasil coated which reduces wear and friction. We also have ...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $6,080.40
Make a selection 100103038TU993 This kit will add 35+ hp and is made for aggressive street or track use. - forged pistons with double hump. - cylinder 107 mm and 114 mm high. - mirrored valve pockets. - deaxiated for trouble free installation. - compression 8.0: 1 made in Germany - made by mahle technical tip - the inside diameter of the heads must be adjusted to accommodate the larger pistons, and to accommodate for the additional thermal load the last 2 ribs should be welded together. We also recommend inserting a groove in the head and using the le mans style rings, part # FVD104999993 General Fitment911 1994-98
From $6,461.47
Make a selection 100105514 This is our camshaft of choice for our tuning kits as it offers unparalleled performance throughout the entire rev range. Performance gains of 30 hp can be had with upgraded boost springs, exhaust, etc. Drivability is enhanced for street performance. This cam is sourced in Germany to ensure quality, reliability and precise fitment. Specifications: 1.26 mm .10 mm the right side is our part # 100105516 General Fitment911 1989-94
From $1,139.51
Make a selection 10010303802 Perfect kit for street use, this is ultra-reliable, factory smooth kit will yield 35+ hp (depending on your additional modifications). These can also be used with OEM valves and camshafts. These are slip fit (107 spigot / 102 bore) and no modifications must be made to the case. Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resistance, they are nikasil coated which reduces wear and friction. We also have the piston rings (sealing and oil scrapers) pre-installed to ensure reliability. Each of our mahle piston and cylinder kits are complete and ready for installation. We also ...(choose a part on the right to read more) General Fitment911 1994-98911 1989-94
From $6,080.40
Make a selection 100105251 Upgraded camshafts offer performance gains across the entire rpm range while retaining drivability around town. These camshafts are manufactured by schrick avl, they are renowned for their quality and performance. Camshaft for inlet and outlet specifications: duration *cra intake: 292* duration *cra exhaust: 284* intake peak timing: 114 exhaust peak timing: 114 cam lift inlet: 8.8 cam lift exhaust: 8.8 valve lift inlet i/e (mm): 13.2 valve timing *cra intake open: 32 valve timing *cra intake close: 80 valve timing *cra exhaust open: 76 valve timing *cra exhaust close: 28 lift at tdc intake: 1.8 lift at tdc exhaust: 1.5 valve clearance intake: hydraulic valve clearance exhaust: hydraulic internal thread, bearing...(choose a part on the right to read more) General Fitment911 1994-98
From $702.67
Make a selection 10010303204 - 3.2 l for increased horsepower and torque.* - genuine mahle forged pistons with deeper valve pockets. - genuine mahle steel (st52) nikasil coated cylinders.** - piston pin bore is off center (deaxiated) for factory quiet operation. - 10.3:1 compression. - 98 mm big bore. - 22x58 racing wrist pins - 70.4 stroke. - made in Germany by mahle gmbh. - piston rings installed directly on the pistons for ease of installation. - complete set with cylinders, pistons, rings, wrist pins and clips. - kit weighs 21.03 lbs. (9.54 kg). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resista...(choose a part on the right to read more)
$9,693.51
Make a selection 1002110221DA This is a high-quality replacement for original number, 911 211 022 10 manufactured by dansk. It is manufactured in stainless steel and includes the necessary brackets and tabs for a direct bolt on replacement. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911100 sold individually. 1 necessary per car.
$1,329.90
Make a selection 1002110212DA This is a high-quality replacement for original number, 911 211 021 14 manufactured by dansk. It is manufactured in stainless steel and includes the necessary brackets and tabs for a direct bolt on replacement. Dansk offers a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. For a proper installation, we recommend heat exchanger installation kit, part # FVDmk911101 sold individually. 1 necessary per car. Please note: the corresponding right side i...(choose a part on the right to read more)
$1,603.80
Make a selection 10021102900 This heat exchanger is engineered for the discerning Porsche 911 3.2 l owner looking for more performance. These are manufactured in stainless steel. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Features: gains of +10 hp and +10-15 tq stainless steel 1.5" pipe diameter for backpressure reduction 21.5 mm thick flange with "fire ring" connects "early style" dual inlet mufflers bolt on replacement for the left side reduces the ...(choose a part on the right to read more)
$1,361.80
Make a selection 100555222MKSG FVD Brombacherrs door hardware kits are perfect reproductions made in Germany. Features: high-strength aluminum door handles that secure to the door durable, triple stitched door pulls genuine handle and pull trim / bezels genuine hardware includes everything necessary for installation made in Germany sold as a set. 1 necessary per car. Please note: if you have electric windows we recommend ordering the switch frames, part # 91161363520 a total of 3 are needed. General Fitment911 1994-98911 1989-94 911 1970-73
From $335.59
Make a selection 12637025CSL Power slot front left cryogenic slotted rotors Porsche 964 Carrera 2 2s 4 4s 90-94 General Fitment911 1989-94
$402.37
Make a selection 100555222MKIR FVD Brombacherrs door hardware kits are perfect reproductions made in Germany. Features: high-strength aluminum door handles that secure to the door durable, triple stitched door pulls genuine handle and pull trim / bezels genuine hardware includes everything necessary for installation made in Germany sold as a set. 1 necessary per car. Please note: if you have electric windows we recommend ordering the switch frames, part # 91161363520 a total of 3 are needed. General Fitment911 1994-98911 1989-94 911 1970-73
From $335.59
Make a selection 10021103000 This heat exchanger is engineered for the discerning Porsche 911 3.2 l owner looking for more performance. These are manufactured in stainless steel by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment suppliers to the Porsche in Germany. Features: gains of +10 hp and +10-15 tq stainless steel 1.5" pipe diameter for backpressure reduction 21.5 mm thick flange with "fire ring" connects "early style" dual inlet mufflers bolt on replacement for the right side re...(choose a part on the right to read more)
$1,733.60
Make a selection 106084 There are not many warning signs of an impending ims failure short of a “death rattle” that occurs as the bearing fails and comes apart. These kits replace the factory sealed bearing with a new, severe duty custom ceramic hybrid roller ball bearing for reduced friction and superior performance in poorly lubricated operating conditions and replaces the factory ims flange hub, bearing support, and fastener with a stronger, revised billet chromoly assembly. The center bearing support also receives an increase in size and no longer is cut for the o-ring that keep engine oil from leaking out of the engine - we have relocated the o-ring to the ims hub flange for added strength to the center stud & bearing support...(choose a part on the right to read more) General FitmentBOXSTER 2005-08BOXSTER 1997-04 911 1998-05 911 1987-89
$899.99
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |